Toro 44527 User manual
1 67-005-0152 Mounting Frame 1
2 67-005-0141 Mounting Pin 2
3 67-004-1161 Lower Mounting Pin 1
4 01-282-0600 PTO Assembly 1
5 67-005-0241 Belt Guard 1
6 67-005-2151 Pulley Shaft 1
7 67-005-0251 Bearing Mount 1
* 67-002-0051 Bearing Mount Assembly
(Incl. Ref. #6,7,13,17,38,39) 1
8 67-005-0131 Lower Support Arm 1
9 67-005-0121 Upper Support Arm 1
10 67-004-1371 Upper Support Arm Brace 1
11 321-6 Capscrew - Hex Hd. 2
12 67-004-0401 Upper Support Hinge Rod 1
13 3253-3 Lock Washer 3
14 01-264-0350 Belt 1
15 01-260-0060 Sheave 1
16 01-260-0150 Sheave 1
17 3256-2 Flat Washer 5
18 01-159-0010 Presto Pin 4
19 01-650-0110 All Thread 1
20 3217-9 Hex Nut 4
21 3253-7 Lock Washer 2
22 3256-6 Flat Washer 1
23 82-004-1171 Key 3
24 3296-39 Lock Nut 1
25 325-6 Capscrew - Hex Hd. 1
26 01-506-0040 Decal - Danger 1
27 01-260-0240 Bushing 2
28 01-163-0030 Socket Head Set Screw 1
29 323-13 Capscrew - Hex Hd. 1
30 3217-7 Hex Nut 6
31 3256-4 Flat Washer 3
32 3272-11 Cotter Pin 2
33 3217-5 Hex Nut 2
34 01-506-0130 Decal - Danger 1
35 323-8 Capscrew - Hex Hd. 2
36 3253-5 Lock Washer 2
37 01-506-0550 Decal - Grease 1
38 01-100-0340 Bearing (see note) 1
39 321-4 Capscrew - Hex Hd. 1
67-002
©The TORO Company - 1994
All Rights Reserved
PARTS LIST &
ASSEMBLY
INSTRUCTIONS
MODEL NO. 44527
67 BLOWER MOUNTING KIT
for 200 SERIES GROUNDSMASTER®(Prior ’89)
FORM NO. 01-502-1300.1
Note: When installing bearing,
apply #609 Loctite to bearing be-
fore pressing into collar.
Ref.
No. Part No. Description No.
Used Ref.
No. Part No.
Description
No.
Used
PARTS LIST
ASSEMBLY INSTRUCTIONS
67 BLOWER MOUNTING KIT
1. Mount the bearing mount assembly (A) to the
rearhousingasshowninFig.1. Fastenthebottom
bolt with a 1/2" lock washer nut. Tighten but leave
nutlooseenoughtopivot. Fastenthe top boltwith
a flat washer, lock washer and a nut. Leave nut
loose.
2. Attach the smaller sheave (3.65") to the pulley
shaft using a 1-1/4" bushing.
3. Attach the larger sheave (5") to the fan shaft
using a 1-1/4" bushing. Line up the fan sheave
with the pulley shaft using a straight edge.
4. Slide the belt onto the sheaves.
5. Pivot the bearing mount assembly (A) on the
bottom slot until proper tension is achieved. The
belt has a 3/16" deflection with5 lbs. offorce when
properly adjusted. Tighten both 1/2" nuts on the
bearing mount.
6. Attach the 3/8" x 5" all thread to the nut on the
housing.
7. Mount the belt guard as shown in Fig. 1. Fasten
securely.
8. Connect the PTO to the pulley shaft using a 3/8
x 2 3/4" capscrew.
12. Install the mounting frame to the lower tube on
the blower using the lower mounting pin to attach.
Secure on both ends with presto pins.
A
5" Sheave
3.65"
Sheave
Pulley Shaft
Pivot Point
Figure 1
Belt Guard
3/8" x 5"
all thread
3/8" x 2-3/4" Capscrew
P.T.O.
Other Toro Blower manuals
Toro
Toro PowerJet F700 User manual
Toro
Toro Pro Force 44552TE User manual
Toro
Toro 850 Super Blower/Vac User manual
Toro
Toro 319000001 User manual
Toro
Toro Flex-Force Power System 51824 User manual
Toro
Toro Air Rake User manual
Toro
Toro 62925 User manual
Toro
Toro Powervac 51988 User manual
Toro
Toro Flex-Force Power System 60V MAX User manual
Toro
Toro Versa Vac 07053 User manual
Toro
Toro Sand Pro Cyclone 1000 User manual
Toro
Toro POWERVAC 51984 User manual
Toro
Toro QuieTech 51589 User manual
Toro
Toro Pro Force 44553 User manual
Toro
Toro ProLine BP6900 User manual
Toro
Toro Versa Vac User manual
Toro
Toro 51702A User manual
Toro
Toro 30855 User manual
Toro
Toro UltraPlus 51621 User manual
Toro
Toro 51557 User manual
