Toro 08860 User manual

Popular Blower manuals by other brands

Weed Eater

Weed Eater VS2000BV instruction manual

KRAUSMANN

KRAUSMANN U37020-00 Operation manual

Bosch

Bosch ALB 36 LI Original instructions

Cub Cadet

Cub Cadet HB425 Operator's manual

GreenWorks Pro

GreenWorks Pro BLB482 Operator's manual

ARIETE

ARIETE 2768 manual

NuTone

NuTone 331H user guide

GÜDE

GÜDE GLB 200 18 Li-Ion Translation of the original instructions

I.VA.CO.

I.VA.CO. SC Series Operating and maintenance manual

DeWalt

DeWalt DCE100 instruction manual

Becker

Becker SV 7.330 operating instructions

Metabo

Metabo AG 18 Pro instructions

Desa

Desa GA3650TB installation instructions

Echo

Echo Power Blower PB-230LN Operator's manual

Echo

Echo PB-413H Operator's manual

Black & Decker

Black & Decker BV3100 instruction manual

Ryobi

Ryobi RY08570 Operator's manual

Haaga

Haaga 355 user manual

1

All Rights Reserved

Printed in the USA

W2008 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Discharge Chute Kit

For Sand Pro, Grounds Pro and Groundsmaster Debris

Blowers

Model No. 08860

Form No. 3324–993 Rev. A

Installation Instructions

Note: If front discharge is desired, an optional Chute,

Toro Part No. 104–0329–01, is available.

1. Remove screws and washers securing deflector to

blower discharge opening (Fig. 1). Remove deflector

and retain for future installation.

Sand Pro Debris Blower Shown

1

2

Figure 1

1. Discharge opening

deflector

2. Deflector mounting screws

2. Mount pivot assembly to top of chute assembly with

(5) 3/8116 x 7/8” lg. carriage bolts, .406 x .813 flat

washers and 3/8–16 locknuts (Fig. 2).

Note: Chute assembly can be rotated 180 degrees for right

or left discharge on debris blower.

1

2

Figure 2

1. Pivot assembly 2. Chute assembly

3. Using (2) 3/8–16 x 7/8” carriage bolts, .406 x .813 flat

washers and 3/8–16 locknuts, mount a cover plate and

spring mount bracket to slot in front of blower

discharge chute (Fig. 3).

4. Using (2) 3/8–16 x 7/8” carriage bolts, .406 x .813 flat

washers and 3/8–16 locknuts, mount a cover plate to

slot in rear of blower discharge chute (Fig. 3).

12

Back

1

Front

Figure 3

1. Cover plate 2. Spring mount bracket

5. Mount a eye bolt to side of chute assembly with (2)

washers and jam nuts. Position eye bolt as shown in

(Fig. 4).

1

Figure 4

1. Eye bolt

6. Mount the deflector to chute assembly with screws and

washers previously removed (Fig. 5).

2

1

Figure 5

1. Deflector

7. Mount chute assembly to discharge opening with a

pivot rod, (2) flat washers and cotter pins. Position

components as shown in figure 6.

1

Figure 6

1. Pivot rod

8. Hook spring onto eye bolt and spring mount bracket

(Fig. 3 & 4).

9. Measure, mark and cut off handle tube to required

length for specific blower application.

Amount to cut off handle tube:

SandPro – 20 to 24 inches

Groundsmaster 200 Blower – 10 to 12 inches

Groundsmaster 300 Blower – 10 to 12 inches

GroundsPro 2000 Blower – None

Cut to length

1

Figure 7

1. Handle

10. Slide handle tube into handle support and loosely

secure with (2) U–bolts, washers and nut (Fig. 8).

1

2

Figure 8

1. Handle tube 2. Handle support

11. Mount handle assembly to blower mounting tabs with

a washer and cotter pin (Fig. 9).

1

2

Figure 9

1. Handle assembly 2. Linkage rod

12. Mount linkage rod to handle assembly with a washer

and cotter pin (Fig. 9).

13. Mount linkage rod to deflector assembly with a washer

and cotter pin (Fig. 10).

1

Figure 10

1. Linkage rod