Tohnichi CTA2-G User manual

CTA2-G,Torque & Angle Wrench

Quick Start

1) Install and charge battery using Tohnichi charger until green light goes on.

2) Set on stable surface (do not move), Power ON ,wait for GOOD

3) Using arrow keys set counter to “000”

4) Press “MD” key for 2 seconds to enter set up menu

5) Setup Menu Select using arrow keys and save by pressing MEM key

SEL Mode-S (Single) or Mode-P (Production)

USEL Select Unit N*m, Kg*fm/Kg*fcm,Ft*lbs/In*lbs

Sng Set snug torque value

An Set angle value

AN-H Set angle upper limit

tUrn Set measurement direction CW or CCW

Ar Auto Reset set time 0.00 = OFF or0.1~5.0 seconds

bU Keypad beeping On/Off

PoFF Auto Power Off, 3min.or 10, 30 or None

do Data Output:, PC, or PRN (printer),

bpS Baud Rate: 9600 or 2400, 4800, 19200

dL Data length 8bit or 7 bit

Prt Parity Even or Odd

dFLt DFT-N donot reset or DFT-Y reset defaults

rtC1 Set Clock (Hour/Month/Second)

Single Tightening Mode

•Move counter off of “000” onto count

•Tighten to snug torque value, buzzer sounds

•Shifts into angle mode; intermittent buzzer warns when approaching set angle (within 20 degrees)

•Target angle alert with solid buzzer and blue LED light

•Release load and press MEM to judge within set range (in Auto reset mode judgment is made

automatically)

Production Tightening Mode (Once in P-Mode, need to reset mode using PC software)

•Set up through PC or on Keypad

•After following basic menu set up and selecting Mode-P

•Select Snug torque, 1st, 2nd, 3rd angle and upper limits for each

•Choose “n”= # of fasteners in the process

•Select: NG setting:

NG_RES=NG data then MEM & move to next

AL_RES= NG data then MEM to save tightening data and restart form beginning

•Press MEM key to start P-Mode, T screen appears to start. Complete process: D-OUT shows

•Press MD key or MEM to return to repeat process,

MD 2X=ALLOUT (go to PC software connect cable & select Data Upload)

MD 3X= D-CLR=delete 1 data, MD 4X=ALLCLR=delete all,

Press MD & C at same time to active

Download Data: Move to highest count included press MD key , STT is lower starting point, N= # data,

Press MEM to download

Deleting Data: Move count to select data, press C to delete one data. Move to highest count press MD

key, STT is lower starting point,

N= #data Press MD & C at same time to delete entire range.

Other manuals for CTA2-G

1

This manual suits for next models

6

Table of contents

Other Tohnichi Power Tools manuals

Tohnichi

Tohnichi FH256MC User manual

Tohnichi

Tohnichi QLLS User manual

Tohnichi

Tohnichi QRSP-SP2-N Series User manual

Tohnichi

Tohnichi PQLZ User manual

Tohnichi

Tohnichi CLE2 User manual

Tohnichi

Tohnichi CEM3-P User manual

Tohnichi

Tohnichi TiQL User manual

Tohnichi

Tohnichi QSP Series User manual

Tohnichi

Tohnichi CMQSP User manual

Tohnichi

Tohnichi DB SERIES User manual

Tohnichi

Tohnichi MTQL User manual

Tohnichi

Tohnichi QL2N User manual

Tohnichi

Tohnichi TW750N2 User manual

Tohnichi

Tohnichi CTB10N2X8D-G User manual

Tohnichi

Tohnichi CSPFHW User manual

Tohnichi

Tohnichi DATA TORK CEM3-G-WF User manual

Tohnichi

Tohnichi WQL Series User manual

Tohnichi

Tohnichi YCL2 User manual

Tohnichi

Tohnichi PHL User manual

Tohnichi

Tohnichi CTA2-G User manual

Tohnichi

Tohnichi QSPCA Series User manual

Tohnichi

Tohnichi PQL User manual

Tohnichi

Tohnichi DATA TORK CEM3-G User manual

Tohnichi

Tohnichi CL2Nx8D-MH User manual

Popular Power Tools manuals by other brands

AEG

AEG OMNI-JS Original instructions

SIP

SIP 01533 manual

Ribimex

Ribimex PRS499 quick start guide

3M

3M Fiber Optic Connector Crimp Tool instructions

Ryobi

Ryobi P524 Operator's manual

ROJEK

ROJEK FSN 300A manual

Kemper

Kemper 1740PRO manual

WABCO

WABCO OptiTire installation manual

EINHELL

EINHELL TE-MS 18/210 Li Original operating instructions

Orgapack

Orgapack OR-T 85 Operating and safety instructions

TOUGHCUT

TOUGHCUT Diamond 400 instruction manual

Yaros

Yaros PB-3603 user manual

Fein

Fein BSS 2.0 E Repair instructions

Baileigh Industrial

Baileigh Industrial SS-2725 Operator's manual

Milwaukee

Milwaukee 2674-20 Operator's manual

Fein

Fein BLs 1.6 parts list

Princess

Princess Electric Multi Sharpener user manual

FOREDOM

FOREDOM K.1050 Operation & maintenance manual