TMG 1260 User manual
Page 0of 12
Page 1of 12
Main specifications
Overall assembled size : L18.2 x W3.66 x H2.2 (m) / L60 x W12 x H7.2 (ft)
Shoulder height : H1.2 (m) / 4ft
Door : W1.2 x H1.8 (m) / 4 x 6 (ft)
Prior to assembly
Please read the instructions carefully before installation. It is important to follow your
local safety regulations and industry standards during installation. Regulations may
include but are not limited to :
Safety helmets, protective eyewear, and clothing
Safety harnesses for all elevated workers
Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not
make any alterations to the structure. Do not hang any weights on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and
where it touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all
parts are included prior to setup.
Page 2of 12
TMG-GH126007 Part List
Parts
code
Graphical
Description
Qty
BOX
1
Peak arch tube
15
1/1
2
Upper rafter tube
30
1/1
3
Shoulder tube
30
1/1
4
Sidewall tube
30
1/1
5
Roof purlin
(horizontal tube)
70
1/1
6
Base plate
31
1/1
6A
Door column base plate
2
1/1
6B
Expansion bolt M10x100mm
66
1/1
7
Front door cross tubes
2
1/1
8
Rear door cross tubes
2
1/1
9
Upper vertical tubes for rear truss
1
1/1
10
Lower vertical tubes for rear truss
1
1/1
11
Door frame cross pull tube
(front truss)
1
1/1
12
Door frame left tube
(front truss)
1
1/1
13
Door frame right tube
(front truss)
1
1/1
14
Door frame column left tube
1
1/1
15
Door frame column right tube
1
1/1
16
Door horizontal tube
4
1/1
17
Film rolling machine guide tube
2
1/1
Page 3of 12
18
Roll film tube
2 group
1/1
19
Tube clamp
6
1/1
20
Door buckle
1
1/1
21
Film rolling machine
2
1/1
22
Reed groove
56
1/1
22A
Clip spring
56
1/1
23
Eight clip spring
30
1/1
24
Pressure film carrier
30
1/1
25
Half round head bolt M6x50
85
1/1
26
Hex bolt M6x45
132
1/1
27
Hex bolt M6x80
2
1/1
28
Self tapping screw #12x25
316
1/1
28A
Self tapping screw #12x35
4
1/1
29
Self tapping screw #12x35
134
1/1
30
Socket wrench
1
1/1
Page 4of 12
30A
Hex wrench
1
1/1
31
Square plug
6
1/1
32
Round plug
6
1/1
33
Braided rope
1 bundle
1/1
34
Adhesive tape
1 volume
1/1
35
Film
1
1/1
36
Board
(not included)
80 metres
Installation steps
Step 1 : Review the whole structure and choose the proper installation site
Choose a solid flat level ground area to set up the building. Do not install the
building on soft ground, wetland, uneven surfaces, sloped surfaces.
We strongly recommend that you build the structure on a solid foundation such as
cement and use anchor bolts on all base plates.
Be aware of the surrounding area. Do not set up the building near snowdrifts, open
flames or exposed electrical wires. Do not keep heat sources near the fabric cover.
Keep the building surroundings clear at all times
Mark the ground in the final building location with a line showing the positions of
base plates, front doors. All lines should be drawn from center to center of all base
plate tubes. Diagonal line X must be equal to Y.
Base plates: all base plates must be installed firmly with expansion bolts (6B) on
this step (refer to figure 1).
Parts used in this step :
Page 5of 12
-
(31) Base plate (#6)
-
(2) Door column base plate (6A)
-
(66) Expansion bolts (6B)
Figure 1
Step 2 : Assemble all trusses
The building includes 15 trusses , Connect all pipes with hex bolt (#26).
Parts used in this step (refer to figure 2) :
-
(1x15) Peak arch tube (#1)
-
(2x15) Upper rafter tube (#2)
-
(2x15) Shoulder tube (#3)
-
(2x15) Sidewall tube (#4)
-
(6x15) Hex bolt (#26)
Page 6of 12
Figure 2
Lay down all (15) trusses on the ground as figure 3 when the assembly is all
completed and before moving to next step.
Figure 3
Step 3 : Put up all trusses (refer to figure 4)
Put up the front truss, use hex bolt (#26) to secure the truss to the base plates.
Parts used in this step :
-
(2) Hex bolt (#26)
Page 7of 12
Figure 4
Repeat above step to put up all other trusses (from 2th to 15th truss), and
connect all purl ins. Now the whole structure is completely up. (refer to figure
5)
Parts used in this step :
-
(70) Roof purlin (#5)
-
(5x15) Half round head bolt (#25)
Figure 5
Page 8of 12
Step 4 : Installation of front and rear trusses
Installation of the front truss. (refer to figure 6)
-
(2) Front door cross tubes (#7)
-
(1) Door frame cross pull tube (#11)
-
(1) Door frame left tube (#12)
-
(1) Door frame right tube (#13)
-
(1) Door frame column left tube (#14)
-
(1) Door frame column right tube (#15)
-
(4) Door horizontal tube (#16)
-
(4) Tube clamp (#19)
-
(10) Half round head bolt (#25)
-
(8) Hex bolt (#26)
-
(6) Square plug (#31)
Figure 6
Installation of the rear truss. (refer to figure 7)
-
(2) Rear door cross tubes (#8)
-
(1) Upper vertical tubes for rear truss (#9)
-
(1) Lower vertical tubes for rear truss (#10)
-
(2) Tube clamp (#19)
-
(4) Hex bolt (#26)
Page 9of 12
Figure 7
The whole structure inspection: check all components and trusses to make
sure the whole structure is squared to the base line drawn at the step 1. All
trusses must be set up righted at 90 degree. All purl ins must be straight in line.
If any purl ins are not in line with they will need to be corrected before moving
to the next step.
Now it is the time to secure all bolts and nuts firmed on the structure. But do
not over-tight the bolts, otherwise the tubes might be damaged.
Step 5 : Installing boards (#36) and reed groove (#22) (refer to figure 8, figure 9)
Fix the board (# 36) with self tapping screw (# 29).
Fix the reed groove (# 22) with the self tapping screw (# 28).
Parts used in this step :
-
(56) Reed groove (#22)
-
(280) Self tapping screw (#28)
-
(134) Self tapping screw (#29)
This manual suits for next models
1
Table of contents
Other TMG Greenhouse Kit manuals
TMG
TMG INDUSTRIAL 25100 User manual
TMG
TMG TMG-GH813 User manual
TMG
TMG TMG-GH1030R User manual
TMG
TMG TMG-GH1020R User manual
TMG
TMG TMG-GH1010R User manual
TMG
TMG TMG-GH1020P User manual
TMG
TMG TMG-GH826 User manual
TMG
TMG TMG-GHD3060 User manual
TMG
TMG TMG-GH2060 User manual
TMG
TMG TMG-GH2030BL User manual
Popular Greenhouse Kit manuals by other brands
ACD PRESTIGE
ACD PRESTIGE MR3 H manual
Vitavia
Vitavia VA0040-TRP Assembly instructions
VegTrug
VegTrug Nursery manual
Riverstone Networks
Riverstone Networks Monticello 041315V Assembly instructions
STC
STC Easy Grow 6x12 Greenhouse Assembly instructions
CLIMA POD
CLIMA POD Spirit V7 Series Assembly instructions
