TKS R2 Guide
TKS
1
988732R2 Reservoir EN, issue 1, 2010-08
Operator’s manual -
Spare parts list
R2
Reservoir
TKSTKS
2
CE - Certicate of conformity
We,
T. Kverneland & Sønner AS,
Kvernelandsvegen 100
N-4355 Kverneland
Norge
declare that the product:
TKS - R2 Reservoir
has been built in conformity with the Machine Directive 2006/42/EC and meets the
relevant fundamental health and safety requirements.
Kverneland, 20 August 2010
Tønnes Helge Kverneland
General manager
Enter the serial number
of the machine here:
T. Kverneland & Sønner AS, manufacturer of agricultural products, reserves the right
to change the design and/ or specication of its products without prior warning.
This does not imply any obligation to modify previously supplied machines.
TKS
3
Guarantee
This TKS product is guaranteed against manufacturing and material defects for one year.
If the owner wishes a defect to be covered by the product guarantee, he or his representative must
inform the dealer of this when ordering parts and/ or repairs.
Claims must be reported within the guarantee period.
The dealer must complete a claims form for each case covered by a guarantee and send it to TKS
or TKS’s distributor/ importer within the 10th of the month following the one in which the defect was
reported.
The defective parts shall be marked with the claim number and be kept for up to 6 months so that
TKS or TKS’s distributor/ importer can inspect them.
Since TKS products are used outside the manufacturer’s control, we can only guarantee the
product quality, and not that it will perform its function, nor are we liable for any consequential
damage.
The guarantee is not valid if:
a) third party spare parts are used, or the product is repaired or altered without the
approval of TKS.
b) the operating and servicing instructions have not been followed.
c) the machine has been used for other purposes than those for which it is designed.
The guarantee does not cover damage due to normal wear and tear.
Ofcial safety regulations specify requirements that apply to the users/ owners and manufacturers
of this machine, relating to the careful review of safety hazards that may arise when this type of
machine is used correctly.
Therefore, TKS and our importer/ distributor are not responsible for the functioning of components
that are not shown in the spare parts catalogue for this product. TKS reserves the right to change
the design of the product without this implying any obligations in relation to previously supplied
machines.
NB! It must be possible to identify all enquiries relating to this product by the product’s serial
number; see page 7 on Machine identication.
TKSTKS
4
Content
CE - Certicate of conformity . . . . 2
Guarantee................... 3
Introduction.................. 6
Machine identication.......... 7
Dimensions R2 Reservoir....... 8
Technical data............... 17
Model description ............ 18
Safety ..................... 19
1 Installing the rails................25
1.1 Recommended rail sizes on .........
1-rail suspension ................26
1.2 Recommended rail sizes on .........
2-rails suspension . . . . . . . . . . . . . . . 26
2 Installation and use of Reservoir R2 27
2.1 Installing the Reservoir in conjunction
with stationary cutter . . . . . . . . . . . . 28
2.2 Use of stationary Reservoir in .......
conjunction with stationary cutter ..28
2.3 Installing the Reservoir on rails in . . . .
conjunction with cutter...........29
2.4 Use of Reservoir on rails in ........
conjunction with cutter ..........29
2.5 Installing stationary Reservoir in . . . . .
conjunction with ceiling-mounted . . . . .
cutter.........................30
2.6 Use of stationary Reservoir in .......
conjunction with ceiling-mounted.....
cutter . . . . . . . . . . . . . . . . . . . . . . . . 30
3 Installing the power supply ........32
3.1 Check list before starting the ........
machine ......................32
4 Controls K2/R2...................33
5 Circuit diagram ..................34
6 Controls R2/K2 FeedRobot ........40
7 Model description and use of ........
spreader unit ....................43
8 Using the machine with spreader .....
unit............................45
9 Main measurements for machine . . . . .
with spreader ....................46
10 Width adjustment on spreader unit . 47
11 Remote control ..................48
12 ECS Electrical documentation .......
for R2 ..........................49
13 Circuit diagram ..................50
13.1 Circuit diagram for input and .......
distribution ....................50
13.2 Circuit diagram for PLS module....51
13.3 Circuit diagram for photocell ......52
TKS
5
14 Maintenance and care ............53
Recycling - waste to resource -.....56
Notes .............................57
Spare parts list R2 Reservoir .........58
TKSTKS
6
Introduction
Congratulations on buying your new TKS product. You have chosen a functional, high quality
product. A network of helpful dealers will be able to advise you on its use, as well as provide
servicing and spare parts.
All TKS products are designed, tested and built in close cooperation with farmers and machine
workshops to ensure optimal efciency and reliability.
Please read this instruction manual carefully and familiarise yourself with the machine‘s manner
of operation before starting to use it. There are many conditions and variables that can affect the
machine’s functionality and manner of operation. It is therefore vital that you consider all known
conditions and adapt usage according to these. A good understanding of the machine‘s manner of
operation and performance, together with a high degree of knowledge with regard to feeding and
feed types/consistencies will ensure the best possible result. The machine is a highly advanced
feed robot that operates without the need for supervision and must be used in accordance with the
applicable instructions from the manufacturer and other regulations in force at any given time.
By being thorough and making the necessary adaptations to local conditions, you will ensure the
best possible results.
Yours faithfully
T. Kverneland & Sønner AS
MEKANISKE
T. Kverneland & Sønner AS,
Kvernelandsvegen 100
N-4355 Kverneland
Norway
www.tks-as.no
Phone : + 47 51 77 05 00
Fax : + 47 51 48 72 28
TKS
7
Machine identication
The machine’s serial number and the address of the manufacturer are written on the machine.
See the illustration on this page.
Please use the information on the name plate when making any enquiries about spare parts or
servicing.
This product is CE marked. This mark, along with the associated written EU conrmation, means
that the product fulls current health and safety requirements, and complies with the following
directives: Machine Directive 2006/42/EC
IR2_02
TKS
3430
2470
530
1060 300
Kan justeres 400 mm i høyde,
og settes for hver 50 mm
Laveste høyde
1490
1490
3430
2470
2960
TKS
8
Dimensions R2 Reservoir
All measurements are in mm
R2 Reservoir autolling 3m
R2 Reservoir stationary 3m
IR2_13
IR2_06
TKS
1490
4550
4080
3590
1490 29702090
5360
6320
5850
9
R2 Reservoir 3m + 1m
R2 Reservoir 3m + 3m
IR2_07
IR2_08
TKS
500
TKS
10
IR2_24
IR2_25
K2/R2 with frame, side dispenser with weight
R2 Reservoir stationary lling
This manual suits for next models
1
Table of contents
Other TKS Farm Equipment manuals
