Timan 3330 User manual

www.timan.dk

”Comfortably Better”

Timan 3330

Type-serialnumber: 712000x00xAAAA

OPERATION MANUAL

CONTENTS

1. MACHINE IDENTIFICATION DATA .........................................................................................2

2. INTENDED USE OF THE MACHINE..........................................................................................4

2.1 WEIGHT TABLE FOR USING TOOLS AND ACCESSORIES............................................................4

2.2 THE PERMISSIBLE LOAD ON THE FRONT OF THE MACHINE......................................................5

2.3 PERMISSIBLE LOAD ON THE REAR END OF THE MACHINE .......................................................6

2.4 MAXIMUM PERMISSIBLE SIDE LOAD OF THE MACHINE ...........................................................7

3. NOISE (SOUND PRESSURE) AND VIBRATIONS ....................................................................8

3.1 SOUND PRESSURE MEASUREMENT ..........................................................................................8

3.2 MEASURING VIBRATIONS........................................................................................................8

4. MACHINE CONSTRUCTION.......................................................................................................9

5. STEERING COLUMN, OPERATOR'S GRIP, CABINET AND AIR SWITCHES....................10

5.1 SIDE PANEL ...........................................................................................................................11

5.2 DISPLAY ................................................................................................................................13

5.3 IGNITION ...............................................................................................................................14

5.4 FOOT PEDALS ........................................................................................................................14

5.5 STEERING COLUMN MULTI-SWITCH ......................................................................................15

5.6 CEILING.................................................................................................................................16

6. MAIN CIRCUIT-BREAKER, FUSES AND RELAYS, ERROR CODES ..................................17

6.1 MAIN CIRCUIT-BREAKER.......................................................................................................17

6.2 MAIN FUSES AND RELAYS REAR. ..........................................................................................18

6.3 FUSES IN THE CABINET ROOF ................................................................................................19

6.4 FUSES IN THE CABIN..............................................................................................................20

6.5 RELAYS FRONT......................................................................................................................21

6.6 13 POLE TRAILER SOCKET REAR............................................................................................22

6.7 ERROR CODES .......................................................................................................................22

7. USE OF THE MACHINE - QR CODE ........................................................................................23

7.1 THE STRUCTURE OF THE MACHINE........................................................................................23

7.2 DRIVING ................................................................................................................................23

7.3 MAINTENANCE......................................................................................................................23

7.4 ADDITIONAL EQUIPMENT ......................................................................................................24

8. MAINTENANCE DATA..............................................................................................................25

8.1 HYDRAULIC OIL ....................................................................................................................25

8.2 COOLANT ..............................................................................................................................25

8.3 LUBRICATION........................................................................................................................25

8.4 ENGINE OIL ...........................................................................................................................25

8.5 AIR CONDITIONING ...............................................................................................................25

8.6 WHEELS ................................................................................................................................25

9. TECHNICAL DATA ....................................................................................................................26

10. CE DECLARATION OF CONFORMITY...............................................................................27

Congratulations on your new Timan 3330

This operator's manual will assist you in the proper use, adjustment and maintenance of your

new machine.

Before you start to drive or work with the new machine, read this operator's manual

thoroughly, in particular the section on safety rules.

The indications right and left in the manual and in spare parts lists is the machine seen from

behind in the driving direction.

1. MACHINE IDENTIFICATION DATA

Manufacturer: Timan A/S

Fabriksvej 13

6980 Tim

Tel.: +45 97 330 360

timan@timan.dk

Seller (to be completed by the seller)

Title / Name

Address

Zip code

State/country

Telephone

MACHINE IDENTIFICATION DATA

Type label

Identification number

712000X00X1001

Type

Serial

Machine number

712000

1001

INTENDED USE OF THE MACHINE

2. INTENDED USE OF THE MACHINE

Timan 3330 is a universal tool carrier that can perform many tasks depending on the type of

equipment attached to it. It could, for example, cut grass, sweep, cut live fences, remove

snow, salt roads etc.

The respective tools may be attached to the machine on the front and at the rear. Furthermore,

a combination of a fork and ball joint for towing tools and carts can be attached to the

machine.

Timan 3330 may drive on public roads, and it is intended for professional operators.

The use of the machine depends on its tasks.

However, you must ensure that the loads and weights specified below will never be exceeded.

Using accessories which exceed the maximum specifications specified below can lead to

malfunctions, machine failure, damage to someone else's property and injury to the driver

and/or other persons. The Timan guarantee does not cover any malfunctions or machine

failures caused by using non-corresponding accessories.

2.1 Weight table for using tools and accessories

Front axle Rear axle Maximum permissible

Maximum permissible Maximum permissible

1300 kg 1300 kg 1860 kg

Important: Only towbars approved by Timan A / S may be fitted.

The maximum permissible load of the towing pole is specified

on the picture. It is important to ensure that the vertical load of

the towing pole is never greater than 120 kg (up/down). This rule

applies even if the vehicle is connected with a coupling head

and in the towing pole.

If the vehicle is connected with a coupling head (see Fig no. 1 and 2), the maximum

permissible weight (total weight) of the vehicle must be 1500 kg if it is

equipped with overrun brakes and 600 kg if it is not.

Alternatively, the towing pole may be loaded with the vehicle,

which is connected in the towing pole (see Fig no. 3). This may

be done with the maximum permissible weight (total weight)

of 1850 kg if the vehicle is equipped with overrun brakes.

If the vehicle is connected with a towing pole, it must be a four-wheel

vehicle (four-wheel drive) with a turntable steering axle

(see Fig. no. 4 and 5) which has a maximum permissible mass

(total mass) of 1850kg if it is equipped with overrun brakes

and 600 kg if it is not.

INTENDED USE OF THE MACHINE

2.2 The permissible load on the front of the machine

The maximum permissible load on the lifting arms is shown in the diagram below

The load must be positioned in the middle between the front wheels.

In the load table, point 0 is shown on the lifting arm handle if it is in a vertical (upright)

position. It is measured from the handle on the lifting arms where the quick coupler is

connected (quick coupler device).

For example, the arms may lift 150 kg with a load placed 800 mm away from handle without

loading the rear end. When minimal load amounting to 200 kg is on the rear end, the arms

may lift 300 kg at the same distance.

100

150

200

250

300

350

400

450

500

-800 -400 0400 800 1200 1600 2000 2400 2800

Till. vægt front -Perm. load front Ingen bagvægt - Without rear weight

Min 200kg bagvægt - Min 200kg rear weight

INTENDED USE OF THE MACHINE

2.3 Permissible load on the rear end of the machine

The maximum permissible load on the rear end of the machine and load platform is specified

in the diagram below.

Caption: Permissible load on the rear end of the machine

The load must be positioned in the middle between the rear wheels.

The maximum permissible load on the load platform is 600 kg above the centre of the rear

wheels.

The distance from centre of the rear wheels to the rear end of the machine is 600 mm.

For example, the rear end may carry a load weighing 400 kg with the centre of gravity

positioned 900 mm away from the centre of the rear wheels - 300 mm if the measurement is

taken from the rear end of the machine.

Important: It is necessary to use the original Timan A/S tool frame when loading the rear

end.

100

200

300

400

500

600

700

0200 400 600 800 1000 1200 1400 1600 1800

Till. vægt bag -Perm. load rear

INTENDED USE OF THE MACHINE

2.4 Maximum permissible side load of the machine

The maximum permissible side load of the machine is specified in the diagram below.

Caption: Maximum permissible side load of the machine

The mass table shows point 0 between the lifting arms and on the ball joint at the rear end of

the machine (if it is attached).

Equipment for side loading may either be fixed to the front on the lifting arms or to the rear.

The stated load is on the lifting arm holder or the rear end of the machine. If the tool is fixed

further away than the holder, on the rear end of the machine, the weight that can be suspended

from the machine decreases.

Important:

Only one side load may be suspended from the machine at a time.

For example, the machine may carry a load weighing 200 kg with the centre of gravity

positioned 1700 mm away from the centre of the lifting arms.

100

150

200

250

300

350

400

0400 800 1200 1600 2000 2400 2800 3200 3600

Till. side vægt -perm. side load

NOISE (SOUND PRESSURE) AND VIBRATIONS

3. NOISE (SOUND PRESSURE) AND VIBRATIONS

3.1 Sound pressure measurement

5 sound pressure measurements were taken on the machine.

Driving noise from the EU 985/2018 Annex II: 74 dB

Standing noise based on EU 985/2018 Annex II: 71 dB

Source strength measurement without equipment LWA based on ISO 6395: 2008 105 dB

Source strength measurement with sweeping n equipment LWA based on ISO 6395: 2008

102 dB

Sound level cabin EU1322 / 2014 method B: 79 dB

3.2 Measuring vibrations

Two vibration measurements were taken

-The vibration of the body on the seat was

measured.

-Vibration of the hands/arms on the steering

wheel was measured.

The measurements were taken with VibroControl.

A test procedure according to DS/EN 1032 was used.

Measurements were taken in 2 various operating situations

-Driving on a road at a speed of 27 km/h.

Motor speed (revolutions) 3600 rpm

-Mowing grass with a Timan 1,35 m mowing conditioner

Driving speed: 6 km/h

Motor speed (revolutions) 3000 rpm

Body vibration when driving on a road: aw max = 0.48 m/s2

Body vibration when mowing grass: aw max = 0.69 m/s2

Vibration of hands and arms when driving on a road:

ahv = 0.60 m/s2

Vibration of hands and arms when mowing grass:

ahv = 1.08 m/s2

Vibration measurement uncertainty: ± 10 %

MACHINE CONSTRUCTION

4. MACHINE CONSTRUCTION

It is an articulated machine which thus has a very small turning radius. The joint is located

midway between the front and rear wheels, thus the rear wheels follow the route of the front

wheels. The joint is firmly attached from the side in order to ensure greater stability when

loads are being lifted. The machine also drives more smoothly on uneven surfaces. The

machine is controlled by a control cylinder and Orbitrol connected to the hydraulic pump,

which facilitates rotation of the steering wheel and machine even in difficult conditions.

The gasoline motor is located in the rear. The driver's cab and lifting arms are located in the

front.

Driving forward is enabled by a hydrostatic device with a pump and 4 hydraulic wheel

motors. The four-wheel drive is always connected in order to ensure optimal tractive force/

pulling force.

The respective tools (attachments) may be attached to the machine on the front and on the

back. The tools may also be lifted with the lifting arms. Furthermore, a combination of a fork

and ball joint for towing tools and carts may be attached to the machine.

Table of contents

Other Timan Farm Equipment manuals

Timan

Timan Comfortably better CS 200 User manual

Popular Farm Equipment manuals by other brands

GSi

GSi PNEG-2314 installation manual

Checchi & Magli

Checchi & Magli TEXDRIVE owner's manual

Amazone

Amazone Cenius 4003-2TX operating manual

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Operator's manual

Cima

Cima BLITZ Maintenance Instruction

Amazone

Amazone CombiDisc 3000 Original operating manual

HE-VA

HE-VA Disc-Roller XL Contour Operating instructions/spare parts list

AGT

AGT AGT-SSFM product manual

Milestone

Milestone 72-84 manual

KUHN

KUHN Hector 3000 Complementary instructions

Krone

Krone X-Disc 6200 operating instructions

Eliet

Eliet DZC450 manual

Taarup

Taarup BIO+ B4000 Operator's manual

Garland

Garland SHAKER 310 DPG instruction manual

stable comfort

stable comfort StableWall System installation guide

Raven

Raven AccuBoom installation manual

International

International 710 Operator's manual

Ashland

Ashland HDW-3217-14 parts manual