ThePondguy SuperFlo 9000 User manual
SuperFlo™ 9,000
High Volume
Pump
Product Manual
TM
Important Information........................2
Technical Specs ............................. 3-4
Installing Your SuperFlo™ Pump .............. 4-5
Cleaning Your SuperFlo™Pump.................6
Replacement Parts & Warranty Information.....7
Additional Notes..............................8
Table of Contents:
For Model:
• SuperFlo™ 9,000
(Item #120225)
ADDITIONAL NOTES:
IMPORTANT INFORMATION:
Please read these instructions thoroughly before use. Failure to follow instructions may result in
equipment damage or failure, losses, injury or death.
DANGER:
To avoid possible electric shock:
• If the power cord has been damaged, DO NOT operate, SuperFlo™ Pump should be replaced.
• If the power cord lead has been damaged, DO NOT operate, SuperFlo™ Pump should be replaced.
• Close supervision is necessary when the unit is used near children.
WARNING:
To reduce the risk of electric shock:
• Connect only to a properly grounded receptacle, which is serviced by a Ground Fault Circuit
Interrupter and never remove the ground pin from the plug.
• Provide a “drip loop”for the power cord. This is a loop in the cord below the level of the receptacle or
plug that prevents water from traveling along the cord in the direction of the receptacle.
• ALWAYS unplug the SuperFlo™ Pump from power source when it is not in use, and before installing,
removing or servicing the SuperFlo™ Pump components.
• DO NOT immerse the SuperFlo™ Pump plug in water or attempt to use a wet plug.
• The SuperFlo™ Pump is NOT suitable for use in swimming pools, swimming ponds, or other
situations where bodily contact is made with the water.
CAUTION:
To reduce the risk of equipment damage or failure:
• DO NOT place SuperFlo™ Pump near ammable or other dangerous materials or objects.
• DO NOT use the SuperFlo™ Pump for uids other than water.
• ALWAYS unplug the unit if there is no water running through it to prevent over heating.
• ALWAYS operate the pump completely submerged for proper cooling.
• DO NOT operate during freezing conditions. Drain SuperFlo™ Pump and store in a protected
location.
IMPORTANT:
The Pond Guy® is not responsible for equipment damage or failure, losses, injury or death resulting
from failure to follow safety precautions, misuse or abuse of equipment.
thepondguy.com | 866-POND-HELP (766-3435)
2
CLEANING YOUR SUPERFLO™PUMP:
SuperFlo™ 9,000
High Volume Pump
A4”Slip Discharge Accommodates 4” Flex PVC Tubing
BSuperFlo™ 9,000 With Stainless Steel Motor Lead &
Quick Release Intake Screen
C50’Power Cord Includes Underwater Quick Disconnect
D3”Slip Adapter Nut Accommodates 3” Flex PVC Tubing
B
D
A
C
Getting to Know Your
SUPERFLO™PUMP
TECHNICALSPECS :
MODEL POWER AMPS MAX FLOW MAX HEAD
HEIGHT PLUMBING SIZE POWER CORD
LENGTH
SuperFlo™ 9000 120V / 60 Hz 5.8 Amps 9,900 GPH 20’
3”or 4” Flexible PVC, Slip
Adaptor Required for 3”
Plumbing (Included). Check
Valve and Rubber Coupler
Recommended (Not Included)
50’Standard
Longer Power
Cords are
Available.
15425 Chets Way | Armada, MI 48005 3
Watch a video of the SuperFlo™ Pump installation
online @ www.thepondguy.com/supero
INSTALLING YOUR SUPERFLO™PUMP:
For Best Results
• Ideally the SuperFlo™ Pump should be
placed in a skimmer or vault, but may
be placed on any at surface away from
sludge or algae mats.
• Keep SuperFlo™ Pump pre-lter free
of debris.
• DO NOT operate during freezing
conditions. Drain the SuperFlo™ Pump
and store in a protected area.
Tools Required: PVC Glue & Primer
TECHNICALSPECSCON’T :
Step 1
Remove End Caps
REMOVE the protective power cord end caps and connect
the power cord to the power lead.
Step 2
Attach Plumbing & Submerge
ATTACH plumbing to the pump discharge using PVC glue and primer. The pump discharge
is set up for 4”plumbing, however 3” may be used with the included reducer tting.
SUBMERGE the SuperFlo™ Pump in a at area in your pond, pump vault or pond skimmer.
Ideally this should be at the opposite end of the pond from where the water will discharge.
thepondguy.com | 866-POND-HELP (766-3435)
4
INSTALLING YOUR SUPERFLO™PUMP:
Step 2 CON’T
If installing in a pump vault or pond skimmer we
recommend connecting a 90 degree elbow, a check
valve* as well as a rubber coupler for easy removal during
maintenance (not included). See image for reference.
*To ensure proper function please reference arrows on your
check valve during installation.
Rubber Coupler
Check Valve PVC Elbow
Step 3
Waterfall
CONNECT the plumbing to your waterfall lter or
spillway. Reference waterfall lter or spillway manual
for proper installation.
Step 4
Plug In
PLUG the power cord into a standard 120-volt GFCI
protected outlet.
INSTALLING YOUR SUPERFLO™PUMP:
15425 Chets Way | Armada, MI 48005 5
WARNING:
Before performing any maintenance, always unplug the SuperFlo™ pump
from the power source.
CLEANINGTHEPREFILTER:
Perform anytime there is a reduction in water ow.
REMOVE large debris from the intake screen and discard. The use of a small brush or cloth may
be helpful. If needed, remove the intake screen nut to clear the inside of the intake screen.
TROUBLESHOOTING :
Pump does not turn on:
• Check that the power cord is connected.
• Check to see if the circuit breaker is tripped.
• GFCI may be faulty.
• Check power cord for damage.
Pump turns on and then shuts o:
• Verify pump is completely submerged for
proper cooling.
• Check for debris clogging the pump intake.
Reduced water ow:
• Check for debris clogging the pump pre-lter
• Verify that the water level is not low.
• Check plumbing for clogs.
• If using a check valve be sure it is installed
correctly.
CLEANING YOUR SUPERFLO™PUMP:
thepondguy.com | 866-POND-HELP (766-3435)
6
DIAGRAM DESCRIPTION PART #
AStainless Housing 651206
BRotor Mounting Plate 651207
CRotor & Impeller Assembly 651204
DRotor Locking Ring 651205
ELower Intake Housing 651202
FLower Intake Screw 651209
GStainless Suction Screen 651201
HSuction Screen Nut 651203
IBearing Holder with Screen 651208
A
B
C
D
E
G
H
F
I
REPLACEMENT PARTS: SUPERFLO™PUMP
PRODUCT WARRANTY:
All SuperFlo™ Pumps carry a 2-year warranty. The Pond Guy® will repair or replace
any units found to be defective. This limited warranty is extended exclusively to the
original purchaser and begins from the date of original purchase receipt. Abuse or
misuse of this product or power cord alterations void all warranty. Please call for a
Return Authorization Number prior to returning product by calling our Customer Care
Department at 866-766-3435. Failure to request an RMA number may result in delay or
dismissal of your warranty claim
15425 Chets Way | Armada, MI 48005 7
View other great products on-line at www.thepondguy.com
THANK YOU FOR CHOOSING:
The Pond Guy®Inc.
We Know Ponds™
15425 Chets Way
Armada, MI 48005
866-POND-HELP (766-3435)
thepondguy.com
ADDITIONAL NOTES:
510467 V2
Table of contents
Other ThePondguy Water Pump manuals
ThePondguy
ThePondguy UtilityFlo Series Maintenance and service guide
ThePondguy
ThePondguy SolidFlo G2 User manual
ThePondguy
ThePondguy RapidFlo 3000 User manual
ThePondguy
ThePondguy MagFlo Series User manual
ThePondguy
ThePondguy MagFlo Series User manual
ThePondguy
ThePondguy MagFlo Mini 210 Instruction Manual
ThePondguy
ThePondguy SolidFlo Series Maintenance and service guide
ThePondguy
ThePondguy Water Garden Aeration Kit User manual
ThePondguy
ThePondguy MagFlo Series User manual
ThePondguy
ThePondguy SolidFlo 1200 User manual
Popular Water Pump manuals by other brands
Sykes AmeriPumps
Sykes AmeriPumps GP100M Operation and maintenance instructions
DUROMAX
DUROMAX XP WX Series user manual
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 operating instructions
Franklin Electric
Franklin Electric IPS Installation & operation manual
Xylem
Xylem e-1532 Series instruction manual
Milton Roy
Milton Roy PRIMEROYAL instruction manual