Texas Instruments TUSB320-LA-EVM User manual

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

User's Guide

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

This document describes how to use TUSB320-LA-EVM and TUSB320-HA-EVM evaluation modules.

Throughout this document, TUSB320-xA-EVM,evaluation modules, and EVM are used to identify the

TUSB320-LA-EVM and TUSB320-HA-EVM.

Contents

1 What is the TUSB320-LA-EVM and TUSB320-HA-EVM?.............................................................. 2

2 TUSB320-LA-EVM and TUSB320-HA-EVM Features.................................................................. 3

2.1 Power................................................................................................................. 3

2.2 VBUS................................................................................................................. 3

2.3 DIP Switch Setting.................................................................................................. 4

2.4 I2C..................................................................................................................... 4

2.5 LEDs.................................................................................................................. 4

3 TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples................................................ 5

3.1 UFP Operation ...................................................................................................... 5

3.2 DFP Operation ...................................................................................................... 6

3.3 DRP Operation...................................................................................................... 7

4 EVM Schematics............................................................................................................. 9

4.1 TUSB320-LA-EVM Schematics................................................................................... 9

4.2 TUSB320-HA-EVM Schematics................................................................................. 12

List of Figures

1 Example Configuration Using HD3SS2522 and TUSB320-xA-EVMs ................................................ 5

2 Example Configuration Using Two TUSB320-xA-EVMs................................................................ 6

3 Example Configuration Using HD3SS2522 and TUSB320-xA-EVMs ................................................ 7

4 Example Configuration Using Two TUSB320-xA-EVMs................................................................ 8

5 TUSB320-LA-EVM Schematic ............................................................................................. 9

6 TUSB320-LA-EVM Components......................................................................................... 10

7 TUSB320-LA-EVM Power................................................................................................. 11

8 TUSB320-HA-EVM Schematic ........................................................................................... 12

9 TUSB320-HA-EVM Components ........................................................................................ 13

10 TUSB320-HA-EVM Power ................................................................................................ 14

List of Tables

1 DIP Switch Modes of Operation ........................................................................................... 4

2 LEDs Debug Descriptions .................................................................................................. 4

3 TUSB320LA/HA UFP DIP Switch SW1 Settings ........................................................................ 5

4 TUSB320LA/HA DFP EVM DIP Switch SW1 Configuration ........................................................... 6

5 TUSB320LA/HA DRP EVM DIP Switch SW1............................................................................ 7

6 TUSB320LA/HA DRP DIP Switch SW1 Configuration.................................................................. 8

Trademarks

All trademarks are the property of their respective owners.

5 V DC IN

Type-C

Connector

uAB USB2

Connector

TUSB320-LA-EVM

TUSB320

What is the TUSB320-LA-EVM and TUSB320-HA-EVM?

www.ti.com

2SLLU235A–January 2016–Revised November 2018

Submit Documentation Feedback

TUSB320-LA-EVM and TUSB320-HA-EVM

1 What is the TUSB320-LA-EVM and TUSB320-HA-EVM?

The EVM is designed to evaluate TUSB320LA/HA devices. The EVM can be configured to operate in

DFP, UFP, or DRP mode via DIP switch selection and/or I2C control. All of the control inputs are also

selectable via DIP switch configuration. The TUSB320LA/HA devices can be used with legacy USB

systems or Type-C systems for evaluation purposes.

www.ti.com

TUSB320-LA-EVM and TUSB320-HA-EVM Features

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

2 TUSB320-LA-EVM and TUSB320-HA-EVM Features

The EVM can be configured for the evaluation of DFP, UFP, or DRP Type-C implementation. The EVM

can also be configured to operate in I2C or GPIO mode. Default configuration is I2C.

This section describes EVM features enabling users to evaluate Type-C implementations in different

modes of operation.

2.1 Power

The EVM can be powered by USB VBUS or 5-V to 5.5-V DC IN through a power jack J5 (2-mm positive

tip, 6.5-mm negative outer shield). The VBUS can be provided via a legacy connection or Type-C

connection. When the EVM operates in DFP mode, the VBUS is provided through micro-AB connector J6,

if the board is connected to a USB host or VBUS source. When the EVM operates in UFP mode, the

VBUS is provided through Type-C connector J1, if the board is connected to a USB host or VBUS source

through a Type-C cable. The 5-V DC IN (J5) can also be used to supply power if a stand-alone operation

is desired without connecting to a USB VBUS power source. Due to diode/IR drop in the test setup, the

VBUS on the connector may be below the desired level. The board is designed to take up to 5.5 V

through DC_5V IN or TP5 (PWRIN) header for test purposes.

If D9 is installed on the board, do not connect the EVM to a USB Host system through the micro AB

USB2 connector(J6) at the same time 5 V is supplied through 5 V DC IN J5 or Type-C Connector J7.

Test loops and headers to power rails and GND are provided for test purposes. Some power rails can be

isolated from the main power supply by removing ferrite beads or passive components. Refer to the

schematics for power rail connection details. Do not supply external power through the test headers/loops

unless the power rail has been isolated from other power sources. In normal operation, power must be

provided through the USB connectors or DC power barrel only: J7, J6, or J5.

2.2 VBUS

2.2.1 VBUSOff time

To meet the VBUSOff time of 650 ms, remove the 10-µF capacitor C1. Current limiting can be reduced to

3 A–3.5 A by changing the R30 value to 47 kΩ.

2.2.2 VBUS Min Level

VBUS, provided on J1 or J6 may be lower than 4.75 V. For bus-powered devices to be attached to the

EVM for test purposes, TI recommends using a 5.5-V external power supply through J5 or TP5.

TUSB320-LA-EVM and TUSB320-HA-EVM Features

www.ti.com

4SLLU235A–January 2016–Revised November 2018

Submit Documentation Feedback

TUSB320-LA-EVM and TUSB320-HA-EVM

2.3 DIP Switch Setting

The DIP switch (SW1) is provided to configure the EVM in different modes of operation.

Table 1. DIP Switch Modes of Operation

Reference

Designator SW Control

Function Default

Switch Setting Description

SW1.1 EN# for TUSB320LA

EN for TUSB320HA ON for TUSB320LA

OFF for TUSB320HA EN# or EN = High, if SW1.1 = OFF

EN# or EN = Low, if SW1.1 = ON

SW1.2 OUT2 OFF OUT2 = SCL with a pullup, if SW1.2 = OFF

OUT2 connected to LED, if SW1.2 = ON

SW1.3 OUT1 OFF OUT1 = SDA with a pullup, if SW1.2 = OFF

OUT2 connected to LED, if SW1.2 = ON

SW1.4 ADDR OFF For I2C mode of operation:

ADDR = High, if SW1.4 = OFF

ADDR = Low, if SW1.4 = ON

For GPIO mode of operation:

Remove R12 and SW1.4 = OFF

SW1.5 INT OFF INT = High, if SW1.5 = OFF

INT = OUT3, if SW1.5 = ON

SW1.6 320_VBUS OFF 320_VBUS = high/low or open if option resistors are

populated. Don’t care in normal operation.

SW1.7 PORT_H OFF PORT = Open, if SW1.7 = OFF

PORT = High, if SW1.7 = ON

SW1.8 PORT_L ON PORT = Open, if SW1.8 = OFF

PORT = Low, if SW1.8 = ON

2.4 I2C

The I2C bus can be accessed through a header: J1 or J2. 4.7-kΩpullups to 3.3 V are added on I2C SCL

and SDA. The ADDR pin can be pulled high or low through DIP SW configuration described in

Section 2.3,DIP Switch Setting. The ADDR pin determines the last bit of the TUSB320LA/HA I2C address

to be high or low. J1 is intended to match the Aardvark I2C programmer dongle pinout.

2.5 LEDs

Several LEDs are provided for easier debug purposes.

Table 2. LEDs Debug Descriptions

Reference Designator LED Name Description

D1 OUT1 Valid only in GPIO mode. Illuminates if OUT1 pin driven low.

D2 OUT2 Valid only in GPIO mode. Illuminates if OUT2 pin driven low.

D3 OUT3 Valid only in GPIO mode. Illuminates if OUT3 pin driven low.

D4 320 ID Illuminates if the ID pin of TUSB320LA/HA is driven low.

D10 POWER Illuminates if 5-V power is available.

Note that the OUT1, OUT2, OUT3 LEDs are used in GPIO mode of operation. The DIP SW must be

configured accordingly to configure the TUSB320-LA-EVM/TUSB320-HA-EVM in GPIO mode of operation.

The LED may light up dim even when OUT pins are not driven due to a pullup to 3.3 V.

USB Host

Type C

USB

Type C

Micro

USB

USB Hub/Device

Configured as

UFP

Type-A to

micro-B

Cable

Micro AB to

Type-A

Receptacle

HD3SS2522 EVM TUSB320-xA-EVM

www.ti.com

TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

3 TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples

This section provides different configuration examples of the TUSB320-LA-EVM and TUSB320-HA-EVM:

DRP, DFP, or UFP operation. The PORT pins and the I2C must be programmed for the corresponding

mode of operation. No external 5-V DC IN is needed unless the board is to operate standalone without

any connections to the USB upstream or downstream port.

3.1 UFP Operation

The board can be configured to operate in UFP mode using the PORT pin on the board or I2C register

setting. If the PORT pin is to be used, SW1.8 must be switched ON and the Mode_Select bits at addr0x0A

bit 5:4 must be set to 00b. The Mode_Select is 00b by default, so there is no need to re-program unless it

has been reconfigured for other modes of operation.

Figure 1 describes an example configuration using HD3SS2522 and TUSB320-xA-EVM. The HD3SS2522

is a TI DFP CC controller, compliant to USB Type-C spec v1.1.

Figure 1. Example Configuration Using HD3SS2522 and TUSB320-xA-EVMs

1. TUSB320LA/HA UFP: Configure the DIP switches as shown in Table 3.

Table 3. TUSB320LA/HA UFP DIP Switch SW1 Settings

Reference Designator SW Control Function Switch Setting

SW1.1 EN#/EN ON for TUSB320LA

OFF for TUSB320HA

SW1.2 OUT2 OFF

SW1.3 OUT1 OFF

SW1.4 ADDR OFF

SW1.5 INT OFF

SW1.6 320_VBUS Don’t care

SW1.7 PORT_H OFF

SW1.8 PORT_L ON

2. Connect the HD3SS2522 EVM to a USB host.

3. Connect TUSB320LA/HA to the HD3SS2522 using a Type-C Cable. VBUS should be provided over

the Type-C cable connection. LED D10 should illuminate on the TUSB320LA/HA board. D3 and D4

should illuminate on the HD3S2522 indicating an UFP connection. Refer to the HD3SS2522 users

manual (SLLU215) for the details of the HD3SS2522 EVM operation.

4. USB devices plugged into the Micro AB USB receptacle (J6) of the TUSB320LA/HA UFP EVM should

enumerate at USB2 speed: HS, FS, or LS.

Type-A to

micro-B

Cable

USB Host

Type C

TUSB320-xA-EVM

Micro

USB

Type C

TUSB320-xA-EVM

Micro

USB

USB Hub/Device

Configured as

UFP

Micro AB to

Type A

Receptacle

Configured as

DFP

TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples

www.ti.com

6SLLU235A–January 2016–Revised November 2018

Submit Documentation Feedback

TUSB320-LA-EVM and TUSB320-HA-EVM

3.2 DFP Operation

The board can be configured to operate in DFP mode using the PORT pin on the board or I2C register

setting. If the PORT pin is used, SW1.7 must be switched ON and the Mode_Select bits at addr0x0A bit

5:4 must be set to 00b. The Mode_Select is 00b by default, so there is no need to reprogram unless it has

been reconfigured for other modes of operation.

Figure 2 describes an example configuration using two TUSB320-xA-EVMs: one configured as DFP, the

other configured as UFP. Refer to Section 3.1 for TUSB320LA/HA UFP EVM configuration.

Figure 2. Example Configuration Using Two TUSB320-xA-EVMs

1. Configure TUSB320LA/HA DFP EVM DIP switch SW1 as shown in Table 4.

Table 4. TUSB320LA/HA DFP EVM DIP Switch SW1

Configuration

Reference

Designator SW Control Function Switch Setting

SW1.1 EN#/EN ON for TUSB320LA

OFF for TUSB320HA

SW1.2 OUT2 OFF

SW1.3 OUT1 OFF

SW1.4 ADDR OFF

SW1.5 INT OFF

SW1.6 320_VBUS Don’t care

SW1.7 PORT_H ON

SW1.8 PORT_L OFF

2. Connect TUSB320LA/HA DFP EVM to a legacy USB host using a Type-A to micro-B cable via micro-

AB connector (J5) provided on board. The LED D10 should illuminate by the VBUS provided by the

legacy USB host over the Type-A to micro-B cable connection.

3. Connect TUSB320LA/HA UFP EVM to the TUSB320LA/HA DFP EVM using a Type-C Cable. The

TUSB320LA/HA UFP EVM should be powered by VBUS provided over the Type-C cable connection.

The LED D10 on the TUSB320LA/HA UFP EVM should also light up. Upon the Type-C cable, attach to

the TUSB320LA/HA DFP EVM, D4 should light up indicating the ID pin has been driven low from the

TUSB320LA/HA.

4. The USB device plugged into the micro-AB USB receptacle (J6) of the TUSB320LA/HA UFP EVM

should enumerate at USB2 speed: HS, FS, or LS.

USB Host

Type C

USB

Type C

Micro

USB

USB Hub/Device

Configured as

DRP

Micro AB to

Type-A

Receptacle

HD3SS2522 EVM TUSB320-xA-EVM

www.ti.com

TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

3.3 DRP Operation

The board can be configured to operate in DFP mode using the PORT pin on the board or I2C register

setting. If the PORT pin is used, SW1.7 must be switched ON and the Mode_Select bits at addr0x0A bit

5:4 must be set to 00b. The Mode_Select is 00b by default, so there is no need to reprogram unless it has

been reconfigured for other modes of operation. It is important that both SW settings are in the OFF

position to have the PORT input to the TUSB320LA/HA open.

Figure 3 illustrates an example configuration using HD3SS2522 and TUSB320-xA-EVMs. The

HD3SS2522 is a TI DFP CC controller, compliant to USB Type-C spec v1.1.

Figure 3. Example Configuration Using HD3SS2522 and TUSB320-xA-EVMs

1. Configure the TUSB320LA/HA DRP EVM DIP switch SW1 as shown in Table 5.

Table 5. TUSB320LA/HA DRP EVM DIP Switch SW1

Reference

Designator SW Control Function Switch Setting

SW1.1 EN#/EN ON for TUSB320LA

OFF for TUSB320HA

SW1.2 OUT2 OFF

SW1.3 OUT1 OFF

SW1.4 ADDR OFF

SW1.5 INT OFF

SW1.6 320_VBUS Don’t care

SW1.7 PORT_H OFF

SW1.8 PORT_L OFF

2. Connect the HD3SS2522 EVM to a USB host.

3. Connect the TUSB320LA/HA to the HD3SS2522 using a Type-C cable. VBUS should be provided over

the Type-C cable connection. LED D10 should light up on the TUSB320LA/HA board. D3 and D4

should light up on the HD3S2522 indicating an UFP connection. Refer to the HD3SS2522 users

manual (SLLU215) for details on the HD3SS2522 EVM operation.

4. The USB devices plugged into the micro-AB USB receptacle (J6) of the TUSB320LA/HA UFP EVM

should enumerate at USB2 speed: HS, FS, or LS.

Type-A to

micro-B

Cable

USB Host

Type C

Micro

USB

Type C

Micro

USB

USB Hub/Device

Configured as

UFP

Micro AB

to Type-A

Receptacle

Configured as

DRP

TUSB320-xA-EVM TUSB320-xA-EVM

TUSB320-LA-EVM and TUSB320-HA-EVM Configuration Examples

www.ti.com

8SLLU235A–January 2016–Revised November 2018

Submit Documentation Feedback

TUSB320-LA-EVM and TUSB320-HA-EVM

Figure 4 describes an example configuration using two TUSB320-xA-EVMs: one configured as DRP, the

other configured as UFP. Refer to Section 3.1 for TUSB320LA/HA UFP EVM configuration.

Figure 4. Example Configuration Using Two TUSB320-xA-EVMs

1. Configure the TUSB320LA/HA DRP DIP switch SW1 as shown in Table 6.

Table 6. TUSB320LA/HA DRP DIP Switch SW1

Configuration

Reference

Designator SW Control Function Switch Setting

SW1.1 EN#/EN ON for TUSB320LA

OFF for TUSB320HA

SW1.2 OUT2 OFF

SW1.3 OUT1 OFF

SW1.4 ADDR OFF

SW1.5 INT OFF

SW1.6 320_VBUS Don’t care

SW1.7 PORT_H OFF

SW1.8 PORT_L OFF

2. Connect the TUSB320LA/HA DRP EVM to a legacy USB host using a Type-A to micro-B cable via

micro-AB connector (J5) provided on the board. The LEDs D1, D2, and D3 should be lit up by the

VBUS provided by the legacy USB host over the Type-A to micro-B cable connection.

3. Connect the TUSB320LA/HA UFP EVM to the TUSB320LA/HA DFP EVM using a Type-C cable. The

TUSB320LA/HA UFP EVM should be powered by VBUS provided over the Type-C cable connection.

The LED D10 on the TUSB320LA/HA UFP EVM should also light up. Upon the Type-C cable attached

to the TUSB320LA/HA DFP EVM, D4 should light up indicating the ID pin has been driven low from the

TUSB320LA/HA.

4. The USB device plugged into the micro-AB USB receptacle (J6) of the TUSB320LA/HA UFP EVM

should enumerate at USB2 speed: HS, FS, or LS.

NOTE: Two TUSB320-xA-EVMs can be used for DRP to DRP connection. In this configuration, it is

not recommended to connect the EVM to legacy USB systems as the role cannot be

predicted until both sides enter the attach state. This configuration can be used for

evaluation purposes with 5 V provided via DC IN (J5) on both boards. One of the

TUSB320HA EVMs can be configured to be a preferred SRC or SNK by enabling the

TRY.SRC or TRY.SNK feature via I2C access. Refer to the device datasheet for details on

how to enable this feature.

CC1

CC2

TypeC_VBUS

VBUS SW

VBUS_DET

CC1

CC2

Type C

Receptacle

micro AB

Receptacle

D+

D-

uAB_VBUS

DC_IN

DC IN

Test Header/

Switch

EN#

ADDR

PORT

OUT[1,2,3]

TUSB320LA

Vdd

VDD_320

PWR_IN

TPS63020

TPS25910

4.5V-5.5V

www.ti.com

EVM Schematics

SLLU235A–January 2016–Revised November 2018

TUSB320-LA-EVM and TUSB320-HA-EVM

4 EVM Schematics

4.1 TUSB320-LA-EVM Schematics

Figure 5,Figure 6, and Figure 7 illustrate the TUSB320-LA-EVM revision B schematics.

Figure 5. TUSB320-LA-EVM Schematic

SilkScreen: I2C

SILKSCREENGND

GND

SILKSCREEN

SilkScreen: TestPoint

SilkScreen:

GND

SilkScreen:

SDA/OUT1

SCL/OUT2

INT/OUT3

CC1

CC2

32xID

EN_DIR

OUT1

SilkScreen:

OUT2SilkScreen:

OUT3SilkScreen:

32xIDSilkScreen:

NOTE: ALL DIFF PAIRS ARE

ROUTED 85 TO 90 OHMS

DIFFERENTIAL AND 50 OHMS

COMMON MODE. ALL OTHER

TRACES ARE 50 OHM.

LEDs

Test Header

microAB Receptacle

SilkScreen:

EN#

ADDR

OUT1

OUT2

OUT3

PORTH

PORTL

DIP Switches

Type C Connector

SilkScreen: CSBU1

CSBU2

SilkScreen:

TypeC Connector Pin Mapping

DN2

VBUS

GND

SBU2

B12

B11

CC1

B10

DP1

GND

DN1

SSTXP1

VBUS

SBU1

SSTXN2

SSTXN1

SSTXP2

SSRXP1

SSRXP2

SSRXN1

SSRXN2

SSTXP1

SSTXP2

DP2

SSTXN1

SSTXN2

CC2

VBUS

GND

VBUS

A10

A11

SSRXP1

A12

SSRXN1

SSRXP2

SSRXN1

STUB on DP or DN

no greater than

3.5mm

Test

Purposes

Only

TUSB320HA

Max Value 220uF

SilkScreen:

VDD VDD32x

SilkScreen:

CC1

SilkScreen:

CC2

NOTE: Place LP1, LP2, LP3, LP4 and LP5 5mm away from U1 socket outline

32xVBUS

SilkScreen:

GND

SilkScreen:

I2C

Recommended for ESD protection.

ADDR=L: DNI R10, Install R176

ADDR=H: Install R10, DNI R176

TUSB320HA Default

32xVBUS

VBUS detection option for EN

SCL_OUT2

SDA_OUT1

USB2_P0

USB2_N0

CC1

CC2

SDA_OUT1

SCL_OUT2

OUT1

OUT1_RED

OUT2

OUT2_RED

OUT3

OUT3_RED

ID_RED 320_ID320_ID_D

PORT

PORT_L

PORT_H

SCL_OUT2

EN#_SW EN#_PD

SDA_OUT1

ADDR

INT_OUT3

OUT1

OUT3

320_VBUS_L

CC1

CC2

CSBU1

CSBU2

USB2_P0

USB2_N0

CSBU1

CSBU2

INT_OUT3

CC1

CC2

CC1_R

CC2_R

ADDR

SCL_OUT2

SDA_OUT1

PORT

320_VBUS

OUT2

GPIO_MD

320_ID

INT_OUT3

microAB_ID

320_ID

USB2_P0

USB2_N0

CC2

CC1

CC2

CC1

USB2_P0

USB2_N0

320_VBUS

EN#_SW

EN#

microAB_ID

EN#

micAB_VBUS

VDD_320

TypeC_VBUS

VDD320_LPVDD_320 TypeC_VBUS

VDD_3P3V

TypeC_VBUS

320_ID pg3

R8 500R

200K

HEADER 7X2 0.1" thru-hole

D12

NC, RB751V-40

1 2

C14

NC, 10uF

LED Red 0805

C15

NC, 10uF

R38

NC, 100K

R13

4.7K

R178

R176

10uF J6

USB2_micAB_Recept

VBUS

D-

D+

GND

Shield1 6

Shield2 7

Shield3 8

Shield4 9

Shield5 10

Shield6 11

TP3

15-mil TEST PAD

R12

100K

R37

NC, 1M +/-1%

NC, 10uF

C12

NC, 1nF

C11

0.1uF

R182 1M +/-1%

TP4

15-mil TEST PAD

R14

NC, 100K

R181 0

R11

4.7K

R23 500R

R16 500R

SW1

8-POS 50-MIL SMT

TDA08H0SK1R

C&K (ITT-CANNON)

LP5

TP7

0.1" Test Post

R5 NC, 0

LP6

R20

4.7K

TUSB320HA

CC1

CC2

PORT 3

VBUS_DET 4

ADDR

INT#/OUT3

SDA/OUT1

SCL/OUT2

8ID 9

GND

EN 11

VDD 12

R18

TPD4E05U06

D1+

D1-

GND

D2+

D2-

5NC6 6

NC7 7

GND1 8

NC9 9

NC10 10

R10

100K

R6 1M +/-1%

FB1

220 @ 100MHZ

R40 0

TP8

0.1" Test Post

LP2

TP1

0.1" Test Post

Header 5x2 0.1" thru-hole

R35 0

USB_TypeC_Receptacle_Topmount

GND0 A1

SSTXP1 A2

SSTXN1 A3

VBUS1 A4

CC1 A5

DP1 A6

DN1 A7

SBU1 A8

VBUS2 A9

SSRXN2 A10

SSRXP2 A11

GND1 A12

GND2 B1

SSTXP2 B2

SSTXN2 B3

VBUS3 B4

CC2 B5

DP2 B6

DN2 B7

SBU2 B8

VBUS4 B9

SSRXN1 B10

SSRXP1 B11

GND3 B12

Shield1

G1 Shield2

G2 Shield3

G3 Shield4

G4 Shield5

G5 Shield6

LED Red 0805

LP3

R179

100K

TP2

0.1" Test Post

LP1

LP4

R36 0

R21 500R

R17

R177

LED Red 0805

EVM Schematics

www.ti.com

10 SLLU235A–January 2016–Revised November 2018

Submit Documentation Feedback

TUSB320-LA-EVM and TUSB320-HA-EVM

Figure 6. TUSB320-LA-EVM Components

This manual suits for next models

Table of contents

Other Texas Instruments Control Unit manuals

Texas Instruments

Texas Instruments BoosterPack IWR1642 User manual

Texas Instruments

Texas Instruments MCT8316AEVM User manual

Texas Instruments

Texas Instruments TRF7962A User manual

Texas Instruments

Texas Instruments INA190EVM User manual

Texas Instruments

Texas Instruments TPA6047A4 User manual

Texas Instruments

Texas Instruments TMS320 Series User manual

Texas Instruments

Texas Instruments TCA8424 User manual

Texas Instruments

Texas Instruments TAS5514B User manual

Texas Instruments

Texas Instruments FPC401 User manual

Texas Instruments

Texas Instruments DAC90 EVM Series User manual

Texas Instruments

Texas Instruments DRV2625 Haptics BoosterPack User manual

Texas Instruments

Texas Instruments TPS630702EVM User manual

Texas Instruments

Texas Instruments TMUXBQB-DYYEVM User manual

Texas Instruments

Texas Instruments TLC5540 User manual

Texas Instruments

Texas Instruments SimpleLink BoosterPack BOOSTXL-CC3120MOD User manual

Texas Instruments

Texas Instruments TPA4411 User manual

Texas Instruments

Texas Instruments SimpleLink CC3235MODS User manual

Texas Instruments

Texas Instruments TPS1213Q1EVM User manual

Texas Instruments

Texas Instruments DRV591 User manual

Texas Instruments

Texas Instruments TCA7408EVM User manual

Texas Instruments

Texas Instruments LED171596AEVM User manual

Texas Instruments

Texas Instruments TPS7A78EVM-011 User manual

Texas Instruments

Texas Instruments TLV320DAC26EVM User manual

Texas Instruments

Texas Instruments bq20z65EVM-001 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual