Texas Instruments BOOSTXL-TPS652170 User manual

SLVUBH6–November 2018

BOOSTXL-TPS652170 EVM User's Guide

User's Guide

SLVUBH6–November 2018

BOOSTXL-TPS652170 EVM User's Guide

The BOOSTXL-TPS652170 is a BoosterPack evaluation module (EVM) for programming samples of the

TPS652170 power management IC (PMIC) with user-defined values for output voltage, sequence timing,

and other critical parameters. Modifying these parameters using the BOOSTXL-TPS652170 allows for

rapid prototyping and quick time to market when using the TPS652170 PMIC to provide power to a variety

of processors and FPGAs.

This document provides a description of how to setup the EVM and re-program the EEPROM memory of

the TPS652170 devices using the BOOSTXL-TPS652170 BoosterPack, an MSP430F5529 LaunchPad,

and the IPG-UI software. The steps in this document describe the procedure for programming samples of

the TPS652170 installed in the socket of the BOOSTXL-TPS652170 printed circuit board (PCB).

Contents

1 Introduction .................................................................................................................. 2

2 Getting Started .............................................................................................................. 4

3 EVM Operation .............................................................................................................. 7

Appendix A Software Instructions............................................................................................... 9

Appendix B EVM Documentation.............................................................................................. 25

List of Figures

1 BOOSTXL-TPS652170 Printed Circuit Board (Top View).............................................................. 3

2 BOOSTXL-TPS652170 and MSP430F5529 LaunchPad Connected................................................. 4

3 BOOSTXL-TPS652170 BoosterPack and MSP430F5529 LaunchPad Block Diagram ........................... 5

4 BOOSTXL-TPS652170 with Socket Open ............................................................................... 8

5 Run the IPG-UI Software .................................................................................................. 9

6 Successful Connection Between Computer and USB2ANY (MSP430F5529 LaunchPad)........................ 9

7 Creating New IPG-UI Project for the TPS652170 ..................................................................... 10

8 TPS652170 Project Introduction Tab in IPG-UI........................................................................ 11

9 Successful Write Access to TPS652170 Notification.................................................................. 12

10 Failed GUI Communication to TPS652170 Notification .............................................................. 13

11 Auto Password Write Enabled............................................................................................ 13

12 DEFDCDC1 Register, Default Value .................................................................................... 13

13 Disable GO Bit in SLEW Register ....................................................................................... 14

14 Modifying DEFDCDC1 Register Value.................................................................................. 14

15 EEPROM-Backed Registers of the TPS652170 (1 of 2).............................................................. 16

16 EEPROM-Backed Registers of the TPS652170 (2 of 2).............................................................. 17

17 TPS652170 Re-Programming Example Block Diagram .............................................................. 18

18 Modifying DCDC2-3, LDOx, and LSx Register Values ............................................................... 19

19 Modifying Sequence (SEQ3-4, SEQ6) Registers...................................................................... 20

20 Manually Writing EE_PROG_BIT to Re-Program EEPROM......................................................... 21

21 Automatically Writing EE_PROG_BIT to Re-Program EEPROM.................................................... 21

22 Registers After Successful Re-Programming (1 of 2) ................................................................. 22

23 Registers After Successful Re-Programming (2 of 2) ................................................................. 23

24 Component Placement—Top Assembly ................................................................................ 25

25 Component Placement—Bottom Assembly ............................................................................ 25

Introduction

www.ti.com

2SLVUBH6–November 2018

Submit Documentation Feedback

BOOSTXL-TPS652170 EVM User's Guide

26 Layout—Top Composite .................................................................................................. 25

27 Layout—Bottom Composite .............................................................................................. 25

28 Top Layer ................................................................................................................... 26

29 Inner Layer 1 (GND Plane) ............................................................................................... 26

30 Inner Layer 2 (Signal) ..................................................................................................... 27

31 Bottom Layer (Top View).................................................................................................. 27

32 BOOSTXL-TPS652170 Schematic ...................................................................................... 29

List of Tables

1 Electrical Connections of Headers ........................................................................................ 6

2 BOOSTXL-TPS652170 Test Point List ................................................................................... 6

3 BOOSTXL-TPS652170 Jumper List ...................................................................................... 7

4 Bill of Materials ............................................................................................................. 30

Trademarks

All trademarks are the property of their respective owners.

1 Introduction

The BOOSTXL-TPS652170 allows designers to program samples of the TPS652170 and verify the values

in the EEPROM match the power-up and power-down sequence requirements of the targeted processor

that will be powered by the PMIC in the final application. The BOOSTXL-TPS652170 BoosterPack EVM is

simple to test, requiring only an MSP430F5529 LaunchPad and USB A-to-micro B cable. With no load or a

light load on the BoosterPack EVM, the power provided by the LaunchPad is sufficient to power the

TPS652170 device, re-program the EEPROM, and perform all of the measurements described in this

document. The 5 V provided by the VBUS wire of the USB cable is the only power input to the

LaunchPad.

The TPS652170 device consists of three step-down converters (DCDC1, DCDC2, DCDC3), one WLED

boost converter (DCDC4), two general-purpose LDO regulators (LDO1, LDO2), and two load switches that

can be purposed as LDO regulators (LS1/LDO3, LS2/LDO4). The output voltage of all the DC/DC

converters and the LDO regulators is programmable. Configuring the load switches as additional LDO

regulators is programmable. The sequence order of all DC/DC converters, the LDOs, and the load

switches can also be programmed and assigned to integer values relative to each other. The sequence

timing and supervisor thresholds are global parameters that can be programmed. The integrated battery

charger of the TPS652170 can also be programmed but the BAT, BAT_SENSE, and TS pins are not

routed out to test points on the BOOSTXL-TPS65218.

Modifying some or all of these register map values and re-programming the EEPROM of the TPS652170

device with the IPG-UI software creates new reset values for the PMIC, which allows the PMIC to power-

on and power-off with the required timing for a variety of processors or FPGAs.

Figure 1 shows the top-side of the BOOSTXL-TPS652170 PCB, on which a socket is placed to install

TPS652170 samples and re-program the samples. The samples can then be removed from the socket

and soldered down on a TPS65217xEVM or prototype PCB to evaluate the power delivery capabilities of

the TPS652170 newly programmed for a specific processor or FPGA. If the output voltages or sequencing

are not ideal for the processor or FPGA on the first attempt, the process can be repeated until the ideal

programming of the TPS652170 device is determined.

www.ti.com

Introduction

SLVUBH6–November 2018

BOOSTXL-TPS652170 EVM User's Guide

Figure 1. BOOSTXL-TPS652170 Printed Circuit Board (Top View)

This procedure requires:

1. An MSP430F5529 LaunchPad development kit, MSP-EXP430F5529LP

2. A USB A to micro B cable (included with the LaunchPad development kit)

3. A BOOSTXL-TPS652170 BoosterPack plug-in module

4. TPS652170 devices (TPS652170RSL)

5. An internet connection

Specific instructions on how to program the TPS652170 using the BOOSTXL-TPS652170 with the IPG-UI

software are provided in Appendix A, while the EVM documentation related to the design of the

BOOSTXL-TPS652170 hardware is provided in Appendix B.

NOTE: All re-programmed EEPROM settings must be validated during prototyping phase to ensure

desired functionality because parts cannot be returned in case of incorrect programming. Any

issues should be reported to the e2e forum.

Introduction

www.ti.com

4SLVUBH6–November 2018

Submit Documentation Feedback

BOOSTXL-TPS652170 EVM User's Guide

1.1 Related Documentation

Texas Instruments, TPS65217x Single-Chip PMIC for Battery-Powered Systems Data Sheet

Texas Instruments, IPG-UI User's Guide

Texas Instruments, TPS65217CEVM User's Guide

Texas Instruments, MSP430F5529 LaunchPad Development Kit (MSP-EXP430F5529LP) User's Guide

1.2 Required Hardware

1.2.1 MSP430F5529 LaunchPad

The MSP430F5529 LaunchPad will serve as a communication interface between the IPG-UI software and

the TPS652170 device. The firmware on the MSP430F5529 needs to be updated before it can

communicate with the TPS652170. Figure 2 shows the BOOSTXL-TP652170 connected on top of the

MSP430F5529 LaunchPad with a micro-USB cable inserted in the LaunchPad.

Figure 2. BOOSTXL-TPS652170 and MSP430F5529 LaunchPad Connected

NOTE: Do not plug the BOOSTXL-TPS652170 BoosterPack into the MSP430F5529 LaunchPad

before the firmware is updated, as described in Section 2.5.

2 Getting Started

Figure 3 shows the high-level block diagram of the BOOSTXL-TPS652170 as it is wired to the

MSP430F5529 LaunchPad through the two 20-pin headers connecting the two PCBs. It also shows the

LaunchPad connected to a computer through a USB cable, which is required for programming the

TPS652170 device.

XU1

Socket

MSP-EXP430F5529LP

MSP430F5529 LaunchPad

J1/J3

20-Pin

Header

MSP430F5529

with

USB2ANY_2.7.0.0_LP.txt

Firmware

P4.1

P4.2

I2C_SDA

I2C_SCL

VBUS

PU.0

PU.1

VSS

P1.6

P2.7

VBUS

D+

D-

GND

3V3

USB_5V

AVCC

DVCC

BOOSTXL-TPS652170

Programming Board

J2/J4

20-Pin

Header

GND

TPS652170

PMIC

DCDC1

DCDC2

DCDC3

LDO1

LS1

USB

LS2

SCL

SDA

nRESET

BAT

Dynamic Power Path

VIN_DCDCx

VINLDO

SYS

DCDC4

Regulators

LS1_IN

LS2_IN

Load Switches

Digital

GPIO(!)

3V3

DCDC1

3V3

LDOPGOOD

P1.5 PWM Out

BOOST_EN

PGOOD_BU

3V3

SW2

SW1

DCDC2

SYS

LDO2

www.ti.com

Getting Started

SLVUBH6–November 2018

BOOSTXL-TPS652170 EVM User's Guide

Figure 3. BOOSTXL-TPS652170 BoosterPack and MSP430F5529 LaunchPad Block Diagram

2.1 Connecting Headers

This section describes the headers on the BOOSTXL-TPS652170 used to connect the BoosterPack EVM

to the MSP430F5529 LaunchPad. There are two sets of headers numbered J1-J4, each set having two

rows of 10 pins, for a total of 40 pins. The outside headers, closest to the board edge, are J1 (left) and J2

(right). The inside headers, closest to the socket on BOOSTXL-TPS652170 and closest to the

MSP430F5529 device on the LaunchPad, are J3 (left) and J4 (right). When connected correctly, all 40

pins of the headers make a physical connection from board to board and the headers numbers line up (in

other words, J1 connects to J1, J2 connects to J2, and so forth.). However, all 40 pins do not make an

electrical connection from the LaunchPad to the BOOSTXL-TPS652170 design.

Getting Started

www.ti.com

6SLVUBH6–November 2018

Submit Documentation Feedback

BOOSTXL-TPS652170 EVM User's Guide

Table 1 lists all of the electrical connections made when the headers of the BOOSTXL-TPS652170 and

MSP430F5529 LaunchPad are connected correctly.

(1) The net named 3V3LP is re-named 3V3SW after the current-limiting switch controlled by S1 and provides a pull-up reference

voltage for SCL, SDA, INT, nWAKEUP, and LED D7 driven by the PGOOD pin of the TPS652170 device.

(2) The BOOST_EN signal is for the TPS61093 and does not connect to the TPS652170. Enabling the boost provides 8 V to the

PWR_EN pin, which is sufficiently high to allow re-programming of the EEPROM.

(3) The net named USBLP is re-named USBSW after the current-limiting switch controlled by S1 and provides power (5 V) to the

USB pin of the TPS652170 device directly from VBUS of the USB cable. USBSW is the only supply available and generates

SYS, which provides power to all VIN_DCDCx pins, VINLDO, and LSx_IN.

Table 1. Electrical Connections of Headers

BOOSTXL-TPS652170 Connecting Headers MSP430F5529 LaunchPad

Device Pin Net Name Pin Number Header Number Pin Number Header Pin Info Net and/or

Device Pin

Name

18 (VIO)(1) 3V3LP 1 J1 1 +3V3 +3V3

9 PWR_EN 2 J1 2 Analog In (A5) P6.5

N/A(2) BOOST_EN 8 J1 8 GPIO(!) P2.7

28 SCL 9 J1 9 I2C SCL P4.2

27 SDA 10 J1 10 I2C SDA P4.1

PAD GND 20 J2 20 GND GND

12(3) USBLP 21 J3 21 +5 V +5 V

PAD GND 22 J3 22 GND GND

46 LDOPGOOD 39 J4 39 PWM Out P2.4

2.2 Test Points

Table 2 lists the test points located on the BOOSTXL-TPS652170. The test points are required to

measure the output voltage and sequence timing of the power rails generated by the TPS652170 device.

Table 2. BOOSTXL-TPS652170 Test Point List

PCB Reference Designator Net Name Type

TP1, TP2, TP3, TP4 GND, PAD (thermal pad) Ground

TP5 PWR_EN Digital input

TP6 LS2_OUT Power output

TP7 LS1_OUT Power output

TP8 VLDO2 Power output

TP9 SYS Power output

TP10 VLDO2 Power output

TP11 VDCDC3 Power output (feedback input)

TP12 AC Power input

TP13 USB Power input

TP14 VDCDC1 Power output (feedback input)

TP15 VDCDC2 Power output (feedback input)

TP16 SCL Digital input

TP17 SDA Digital input/output

2.3 Jumpers

Table 3 lists and describes the jumper headers located on the BOOSTXL-TPS652170 for connecting or

disconnecting nets of the PCB.

www.ti.com

Getting Started

SLVUBH6–November 2018

BOOSTXL-TPS652170 EVM User's Guide

Table 3. BOOSTXL-TPS652170 Jumper List

PCB Reference

Designator Pin Net Name Default Shunt Connection Description

J5 1 DCDC1 - Connect to pin 2 when LS1 is re-

programmed as a load switch

2 LS1_IN Installed LS1 configured as LDO3

3 SYS

1 SYS Installed LS2 configured as LDO4

2 LS2_IN

3 DCDC2 - Connect to pin 2 when LS2 is re-

programmed as a load switch

2.4 Software

The software to be used with the BOOSTXL-TPS652170 EVM is the IPG-UI. Download the following files

to ensure that all of the required software is available on the computer used for testing:

1. The latest revision of the IPG-UI EVM GUI.

2. The latest revision of the TPS652170 IPG-UI device file (TPS652170-1.x.json) and script file

(TPS652170-programming.js) from here.

3. The latest MSP430F5529 LaunchPad USB2ANY firmware (USB2ANY_2.7.0.0_LP.txt) from here.

4. The MSP430_USB_Firmware_Upgrade_Example-1.3.1.1-Setup.exe from the

MSP430_USB_Developers_Package 5_20_06_02.

A detailed set of instructions for using the software, with examples, is provided in Appendix A.

2.5 Update MSP430F5529 Firmware

Update the MSP430F5529 LaunchPad development to the USB2ANY_2.7.0.0_LP.txt file before putting

the BOOSTXL-TPS652170 on the LaunchPad development kit.

1. Press the S5 button while connecting the Micro USB cable.

2. Run the Firmware Upgrade Example.

3. Choose "Select Firmware".

4. Choose "Browse" and select the USB2ANY_2.7.0.0_LP.txt file downloaded previously.

5. Choose "Upgrade Firmware".

6. When complete, disconnect the USB cable.

3 EVM Operation

3.1 Power-On Procedure

Figure 4 shows the BOOSTXL-TPS652170 board with socket XU1 open and a TPS652170 samples

installed correctly. After the socket is closed, the SW1 PWR switch can be moved from the OFF position

to the ON position.

EVM Operation

www.ti.com

8SLVUBH6–November 2018

Submit Documentation Feedback

BOOSTXL-TPS652170 EVM User's Guide

Figure 4. BOOSTXL-TPS652170 with Socket Open

In order for the configurable load switches/LDO regulators (LS1/LDO3, LS2/LDO4) to receive power from

the correct source, shunts must be installed in the correct position on both 3-pin headers (J5 and J6) as

described in Table 3.

SLVUBH6–November 2018

Software Instructions

Appendix A

SLVUBH6–November 2018

Software Instructions

A.1 IPG-UI Software Installation

The following instructions explain how to install the IPG-UI software on a computer. If this software is

already installed, this section may be skipped.

To install the IPG-UI software, first download the IPG-UI software installation package from www.ti.com.

Then unzip and install the IPG-UI software tool onto the computer.

A.2 IPG-UI Setup for BOOSTXL-TPS652170

The following instructions explain how to run, setup, and operate the IPG-UI software on a computer and

connect it to the BOOSTXL-TPS652170.

• Run the IPG-UI software by using the Windows Start Menu and navigating to the Texas Instruments

folder, or by double-clicking the desktop icon, as shown in Figure 5.

Figure 5. Run the IPG-UI Software

• Wait for the program to load.

• Plug in the micro-USB cable to the USB port of the MSP430F5529 LaunchPad and connect the other

end of the USB cable to an open USB2/3 port on the computer.

• Verify that the software is connected to the USB2ANY (MSP430F5529 LaunchPad) as shown in

Figure 6.

Figure 6. Successful Connection Between Computer and USB2ANY (MSP430F5529 LaunchPad)

• Click the drop-down menu in the Create New Project section and select TPS652170-1.x as shown in

Figure 7.

IPG-UI Setup for BOOSTXL-TPS652170

www.ti.com

10 SLVUBH6–November 2018

Submit Documentation Feedback

Software Instructions

Figure 7. Creating New IPG-UI Project for the TPS652170

• Click the Create Project button.

NOTE: After a project is initially created, it is available in the Create Projects from Recent Devices

menu. When a project is saved, it is available in the Open Recent Projects menu.

• The TPS652170 Introduction tab is now displayed, as shown in Figure 8. Click the Get Started button

or the Register Map tab to begin communicating with TPS652170 device.

Table of contents

Other Texas Instruments Control Unit manuals

Texas Instruments

Texas Instruments DRV8846 User manual

Texas Instruments

Texas Instruments TPA6017A2 User manual

Texas Instruments

Texas Instruments TPS25200EVM-618 User manual

Texas Instruments

Texas Instruments ADC12DJ3200 User manual

Texas Instruments

Texas Instruments AFE881H1 User manual

Texas Instruments

Texas Instruments XDS110 User manual

Texas Instruments

Texas Instruments TRF7970A BoosterPack User manual

Texas Instruments

Texas Instruments TRF2443 User manual

Texas Instruments

Texas Instruments TPS54335AEVM-010 User manual

Texas Instruments

Texas Instruments BQ76905 User manual

Texas Instruments

Texas Instruments TUSB564RNQ User manual

Texas Instruments

Texas Instruments TAS6424R-Q1 User manual

Texas Instruments

Texas Instruments DRV10974 EVM User manual

Texas Instruments

Texas Instruments BoosterPack IWR1642 User manual

Texas Instruments

Texas Instruments TPS65313-EVM User manual

Texas Instruments

Texas Instruments 2000 series User manual

Texas Instruments

Texas Instruments LM5123EVM-BST User manual

Texas Instruments

Texas Instruments INA901EVM-CVAL User manual

Texas Instruments

Texas Instruments TAS5755MEVM User manual

Texas Instruments

Texas Instruments bq2427 Series User manual

Texas Instruments

Texas Instruments bq20z65EVM-001 User manual

Texas Instruments

Texas Instruments TPA152 User manual

Texas Instruments

Texas Instruments ADS1 7 EVM-PDK Series User manual

Texas Instruments

Texas Instruments LMK04832EVM-CVAL User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual