Temco TF36 Mounting instructions

7461

TF/TL

cover

2/04

TF/TL Series

Woodburning Fireplace

For Models:

TF36

TF36i

TF42

TF42i

TL36

TL36i

TL42

TL42i

For use in U.S./Canada

Underwriter's Laboratories Report No. MH6018

DO NOT DISCARD THIS MANUAL: Retain for future use.

Homeowner's Installation and Operating Manual

20007461 6/05 Rev. 2

410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7777

www.temcoﬁreplaces.com

CFM Specialty Home Products

TF/TL Series Woodburning Fireplaces

20007461

Safety Information

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING FIREPLACE.

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to

follow these instructions may result in a possible ﬁre hazard and will void the warranty.

Description

The TF/TL Series ﬁreplaces are solid fuel, woodburning

ﬁreplaces. The TF36/42 is a clean-face ﬁreplace and the

TL36/42 unit has ﬁxed grilles.

Precautions

TEMCO Fireplace Products ﬁreplaces and component

parts have been highly tested and will operate safely

when installed in accordance with instructions provided

in this manual. Carefully read and understand all instruc-

tions before beginning installation.

If you notice any damage to ﬁreplace or component parts,

immediately report damage to your TEMCO dealer.

Only use CFM Corporation components or the warranty

will be voided and a ﬁre hazard may be created.

CFM Specialty Home Products warranty will be voided

by and CFM Speciatly Home Products disclaims any

responsibility for the following actions:

• Installation of any damaged ﬁreplace or chim-

ney component;

• Modiﬁcation of ﬁreplace, chimney assembly or

any component parts thereof; (except for chase

ﬂashings as detailed in the Chimney Top installa-

tion instructions).

• Installation other than as instructed by CFM

Specialty Home Products; or

• Installation and/or use of any component part

not manufactured or approved by CFM Special-

ty Home Products in combination or assembly

with a TEMCO ﬁreplace system, notwithstand-

ing any independent testing laboratory or other

third party approval of such component parts

or accessory.

Any such action may possibly cause a ﬁre hazard.

Consult local building codes to ensure that you are in

compliance before installing the ﬁreplace.

Fireplaces must be vented to the out-of-doors.

Do not obstruct or modify air inlets/outlets in any

manner.

Do not install combustible materials on any of the

black ﬁreplace surround.

Burn only solid wood fuel or gas logs.

Do not install a solid fuel burning insert or other

products not speciﬁed for use with this ﬁreplace.

These ﬁreplaces are not approved for installation in

mobile homes.

Proposition 65 Warning: Fuels used in gas, wood-

burning or oil ﬁred appliances, and the products of

combustion of such fuels, contain chemicals known to

the State of California to cause cancer, birth defects

and other reproductive harm.

California Health & Safety Code Sec. 25249.6

Drafts

The ﬁreplace should not be located in areas that create

drafts (ie: frequently opened doors and central heating air

inlets/outlets) that hamper the normal ﬂow of air into the

ﬁre.

Gas Logs

If you plan to install a gas log, the gas line should be

installed before framing the ﬁreplace. The gas line must

be installed by a certiﬁed gas line installer.

Safety Information . . . . . . . . . . . . . . . . . . 2

Speciﬁcations and Framing . . . . . . . . . . 3

Parts Identiﬁcation . . . . . . . . . . . . . . . . . 5

Chimney Requirements . . . . . . . . . . . . . 6

Planning Information . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . 8

Replacement Parts . . . . . . . . . . . . . . . . 19

Accessories . . . . . . . . . . . . . . . . . . . . . 20

Warranty . . . . . . . . . . . . . . . . . . . . . . . . 23

Table of Contents

TF36, TF36i, TF42, TF42i

TL36, TL36i, TL42, TL42i

Listed

UL127 / ULC-S610

Standard for Factory Built Fireplaces

Units:

WF1C02, WF1CI2, WF1R02, WF1RI2, WF2CO2,

WF2CI2, WF2R02, WF2RI2, WF1C04, WF1CI4,

WF1R04, WF1RI4, WF2C04, WF2CI4, WF2R04,

WF2RI4

TF/TL Series Woodburning Fireplaces

20007461

Fig. 2 TL36 Series speciﬁcations and framing.

TL36 Series Woodburning Fireplace — Circulating Model

" (16mm)

" (13mm)

"

36"

(914mm)

34"

(880mm)

40" (1016mm)

"

"

(502mm)

"

(64mm)

" (902mm)

"

(533mm)

"

(197mm)

"

(191mm)

Recessed

Nailing

Flange

FP527

BC36 SPECS

10/28/98

11" Dia.

(279mm)

Rough Opening Width 41"

Rough

Opening

Height

Rough

Opening

Depth

Gas Line

Access

45" (1162mm)

" (1645mm)

"

(187mm)

20"

(508mm)

"

(521mm)

" (559mm)

40"

(1035mm)

"

(372mm)

"

(337mm)

36"

(930mm)

(76mm)

"

(241mm)

"

(191mm)

Outside

Air

Gas Line

Access

Electrical Access

(1041mm)

8" Dia.

(203mm)

" (822mm)

*If elbows are offset to the back of the unit, chase depth will be 22⁵⁄₈" (575mm).

TF36 Series Woodburning Fireplace

Fig. 1 TF36 Series speciﬁcations and framing.

36"

(914mm)

"

(372mm)

"

(337mm)

40" (1016mm)

36"

(930mm)

"

" (16mm)

45" (1162mm)

45"(1162mm)

" (13mm)

"

" (1645mm)

"

(187mm)

20"

(508mm)

"

(521mm)

" (559mm)

"

(502mm)

"

(533mm)

40"

(1035mm)

"

(241mm)

"

(167mm)

"

(191mm)

"

(191mm)

Outside

Air

Gas Line

Access

Gas Line

Access

Electrical Access

Recessed

Nailing

Flange

FP526

BR36 SPECS

10/28/98

11" Dia.

(279mm)

Rough Opening Width 41"

Rough

Opening

Height

Rough

Opening

Depth

3" (76mm)

(1041mm)

8" Dia.

(203mm)

" (822mm)

*If elbows are offset to the back of the unit, chase depth will be 22⁵⁄₈" (575mm).

TF/TL Series Woodburning Fireplaces

20007461

Fig. 4 TL42 Series speciﬁcations and framing.

TL42 Series Woodburning Fireplace — Circulating Model

42"

(1067mm)

34"

(880mm)

46" (1168mm)

"

" (16mm)

" (13mm)

"

"

(502mm)

" (64mm)

" (965mm)

"

(533mm)

"

(197mm)

"

(191mm)

Recessed

Nailing

Flange

FP545

BC42 SPECS

10/28/98

11" Dia.

(279mm)

Rough Opening Width 47"

Rough

Opening

Height

Rough

Opening

Depth

Gas Line

Access

49" (1245mm)

" (1765mm)

"

(187mm)

20"

(508mm)

"

(521mm)

" (711mm)

40"

(1035mm)

"

(372mm)

"

(337mm)

36"

(930mm)

(76mm)

"

(241mm)

"

(191mm)

Outside

Air

Gas Line

Access

Electrical Access

(1194mm)

8" Dia.

(203mm)

" (895mm)

*If elbows are offset to the back of the unit, chase depth will be 22⁵⁄₈" (575mm).

TF42 Series Woodburning Fireplace

Fig. 3 TF42 Series speciﬁcations and framing.

42"

(1067mm)

46" (1168mm)

36"

(930mm)

"

" (16mm)

" (13mm)

"

"

(502mm)

"

(533mm)

"

(197mm)

"

(191mm)

Gas Line

Access

Recessed

Nailing

Flange

FP546

BR42 SPECS

10/28/98

11" Dia.

(279mm)

Rough Opening Width 47"

Rough

Opening

Height

Rough

Opening

Depth

49" (1245mm)

" (1765mm)

"

(187mm)

20"

(508mm)

"

(521mm)

" (711mm)

40"

(1035mm)

"

(372mm)

"

(337mm)

(76mm)

"

(241mm)

"

(191mm)

Outside

Air

Gas Line

Access

(1194mm)

Electrical Access

8" Dia.

(203mm)

" (895mm)

*If elbows are offset to the back of the unit, chase depth will be 22⁵⁄₈" (575mm).

TF/TL Series Woodburning Fireplaces

20007461

WF554

BR/BC

Combo of IWF261 AND IWF265

11/10/97

Chase Installation

Insulation methods shown are optional

for cold climate, not a requirement for

unit operation.

FP554

Fig. 5 Fireplace and chase parts identiﬁcation.

Termination Cap

Storm Collar

Pan Flashing

Draftstop

Standoff

Surround

Damper Control

Gas Line Knockout

(both sides)

Screen

Grate

Firebox

Metal Safety Strips

(1,2 or 3 pieces)

Outside Air Cover Plate

Electrical Access

Gas Line Access

(both sides)

Nailing Flange

Ceiling Level

Firestop

Batt Insulation

(cut our around ﬁrestop)

FP1531

hearth dimensions

9/04 djt

Front Width Back Width Depth

A B C

TF/TL36 33¹⁄₄" 19⁵⁄₈" 15¹⁄₄"

(845 mm) (499 mm) (387 mm)

TF/TL42 39¹⁄₄" 25⁵⁄₈" 15¹⁄₄"

(997 mm) (651 mm) (387 mm)

FP1531

Fig. 4a Hearth dimensions.

TF/TL Series Woodburning Fireplaces

20007461

Chimney

Support

Chimney Requirements - Offset Installations

0 0 0 0 0 3" 11"

1 0 0 0 0 8¹⁄₄" 20"

0 1 0 0 0 11¹⁄₄" 25¹⁄₄"

2 0 0 0 0 13¹⁄₂" 29¹⁄₄"

1 1 0 0 0 16¹⁄₂" 34¹⁄₄"

0 0 1 0 0 20¹⁄₄" 40³⁄₄"

2 1 0 0 0 21³⁄₄" 43¹⁄₂"

0 0 0 1 0 26¹⁄₄" 51¹⁄₄"

0 1 1 0 0 28¹⁄₂" 55¹⁄₄"

1 0 0 1 0 31¹⁄₂" 60¹⁄₄”

0 1 0 1 0 34¹⁄₂" 65¹⁄₂"

0 0 2 0 0 37¹⁄₂" 70³⁄₄"

1 1 0 1 1 41¹⁄₂" 77³⁄₄"

0 0 1 1 1 45" 83³⁄₄"

0 1 2 0 1 47¹⁄₄" 87¹⁄₂"

0 0 0 2 1 51" 94"

0 1 1 1 1 53¹⁄₄" 98"

0 0 3 0 1 56¹⁄₄" 103¹⁄₄"

0 1 0 2 1 59¹⁄₄" 108¹⁄₂"

0 0 2 1 1 62¹⁄₄" 113¹⁄₂"

0 1 3 0 1 64¹⁄₂" 117¹⁄₂"

0 0 1 2 1 68¹⁄₄" 124"

0 1 2 1 1 70¹⁄₂" 128"

0 0 0 3 1 74¹⁄₄" 134¹⁄₂"

0 1 1 2 2 78" 140³⁄₄"

0 0 3 1 2 81" 146"

0 1 0 3 2 84" 151¹⁄₄"

0 0 2 2 2 87" 156¹⁄₂"

0 1 3 1 2 89¹⁄₄" 160¹⁄₄"

0 0 1 3 2 93" 166³⁄₄"

0 1 2 2 2 95¹⁄₄" 170³⁄₄"

0 0 0 4 2 99¹⁄₄" 177³⁄₄"

0 1 1 3 2 101¹⁄₄" 181³⁄₄"

0 0 3 2 2 104¹⁄₄" 186¹⁄₄"

0 1 0 4 2 107¹⁄₄" 191¹⁄₂"

0 0 2 3 2 110¹⁄₄" 196³⁄₄"

0 1 3 2 3 114" 203¹⁄₄"

0 0 1 4 3 117³⁄₄" 209³⁄₄"

0 1 2 3 3 120" 213¹⁄₂"

0 0 0 5 3 123³⁄₄" 220"

30˚ Elbow Offsets

1' 1¹⁄₂'3' 4' Offset Rise

Notes: G + H cannot exceed 20 feet.

Air Space Clearances: SK8 (2-wall) = 1¹⁄₂" and "S" Series (3-wall) = 2"

Illustration Key

The following safety rules apply to

offset installations (letters correspond

with illustration above):

A. Height of the chimney is measured

from the hearth to the chimney exit.

TF/TL36 TF/TL42

Maximum: 90'0" 90'0"

Minimum:

Without Elbows 12' 6" 12' 6"

With 2 Elbows* 14' 6" 14' 6"

With 4 Elbows* 21' 0" 21' 0"

B. Do not use more than 4 elbows per

chimney.

Attach the straps of the return (top)

elbow to a structural framing member.

The offset (ﬁrst) elbow of any pair does

not have straps.

IWF269

C. The chimney cannot be more than 30˚

(45˚ in Canada) from the vertical plane in

any installation*.

D. The maximum length of the angled run

of the total chimney system is 20 feet. (G

plus H cannot exceed 20 feet.)

E. A chimney support (Model SKCS8)

is required every 6 feet of angled run of

chimney. Chimney supports are required

for every 30 feet and 60 feet (SK8 pipe)

or 20 feet and 40 feet (3-wall pipe) of ver-

tical chimney height above the hearth.

Determine the offset distance of your

chimney arrangement from the centerline

of the ﬁreplace to the centerline of the

chimney where it is to pass through the

ﬁrst ceiling.

NOTE: This offset distance may not be

your full offset distance. See Examples 2

and 3.

FP282

MBUF

5/26/96

OFFSET

RISE

FP282

* In Canada, two (2) SK845 are allowed.

Fig. 6. Chimney system requirements.

RISE

OFFSET

E

6 FT.



HEARTH

FLOOR

CHIMNEY

SECTION

CHIMNEY FLUE EXIT

ELBOW

FP269

MBUF

5/16/96

rev. 5/25

30˚ 

OFFSET

ELBOW

30˚ 

OFFSET

ELBOW

30˚ 

RETURN

ELBOW

30˚ 

RETURN

ELBOW

SKCS8 

SUPPORT

Example 1 Example 2 Example 3

TF/TL Series Woodburning Fireplaces

20007461

Planning Information

The Ten Foot Rule

Major U.S. building codes specify a minimum chimney

height above the roof top. The “Ten Foot Rule” is a ﬁre

safety rule and not a draft rule. To ensure proper draft,

it is recommended that you always meet or exceed the

“Ten Foot Rule,” especially when installing a termina-

tion on a high pitch roof. (Fig. 8)

The key points of the "Ten Foot Rule" are:

1. If the horizontal distance from the chimney to the

peak of the roof is 10' (3m) or less, the top of the

chimney must be at least 2' (610mm) above the peak

of the roof, but never less than 3' (914mm) in height

above the highest point where it passes through the

roof.

2. If a horizontal distance from the chimney to the peak

of the roof is more than 10' (3m), a chimney height

reference point is established on the surface of the

roof a distance of 10' (3m) from the chimney in a

horizontal plane. The top of the chimney must be

at least 2' (610mm) above the reference point, but

never less than 3' (914mm) in height above the high-

est point where it passes through the roof.

Determine how the chimney will be run, length of run

and chimney components required to complete the

job. (Fig. 6) Never install a chimney below minimum

heights.

In planning a chimney system, it is important to know:

1. The height of a chimney is measured from the

hearth to the exit point on the termination.

2. A chimney cannot be offset more than 30° from a

vertical plane.

3. A chimney may run straight up or it may be neces-

sary to offset it to avoid obstructions.

4. The maximum length of an angled run (total chimney

system) is 20' (6m).

5. No more than 2 offsets (4 total 30° elbows in U.S./or

2 total 45° elbows in Canada) per ﬁreplace may be

used.

6. A guy wire stabilizer is required for chimneys extend-

ing more than 6' (1.8m) above a roof line.

LTMODEL SK

2 WALL CHIMNEY



TOTAL

LENGTH 

(LT)

INSTALLED

LENGTH 

(L1)

SK81

SK818

SK83

SK84

11¹⁄₂"

17¹⁄₂"

35¹⁄₂"

47¹⁄₂"

10¹⁄₂"

16¹⁄₂"

34¹⁄₂"

46¹⁄₂"

FP288

MBUF-INSTALLED LENGTH

6/17/96

Fig. 7 Installed lengths of chimney sections.

FP288

AC246

Fig. 8 Ten Foot Rule illustration.

2' Min.

Min.

0 To 10'

Min.

0 To 10'

AC246

4/1/96

Reference

Point

Preplanning an installation is very important to ensure

safety and to save time and money. An installer must

predetermine where a ﬁreplace will be set and how the

chimney system will be run.

Mounting the Fireplace

A ﬁreplace may only be mounted on the following sur-

faces:

1. A ﬂat combustible surface.

2. A raised wooden platform.

3. A concrete block or other solid object placed beneath

each of the four (4) corners of the ﬁreplace.

The ﬁreplace must be spaced 1/2" (13mm) from a com-

bustible back wall and 1/2" (13mm) from a combustible

side wall or support. (Page 14, Fig. 20)

Planning The Chimney Run

TF/TL Series Woodburning Fireplaces

20007461

Insulating Fireplace Enclosure

for Cold Climates

Installation

Chimney Supports

The chimney system is supported by the ﬁreplace for

vertical chimney heights less than 30' (9m) above the

hearth. Chimney supports are required if the vertical

height exceeds 30' (9m) with SK8 chimneys or 20'

(6m) with 3-wall chimneys. Locate chimney supports

at ceiling holes or other structural framing at 30' (9m)

(SK8) or 20' (6m) (3-wall) heights. Spacing between

chimney supports must not exceed 30' (9m) (SK8) or

20' (6m) (3-wall). Use Chimney Support Model SKCS8.

(NOTE: The SKCS8 can not be mounted directly

to the ﬁreplace.) Support provided by elbow straps

fulﬁlls the support requirement only if they are spaced

as previously described. (A chimney support is 2¹⁄₂"

(64mm) long when installed.)

Angled chimney runs require a support every 6' (1.8m)

in addition to the elbow straps. Chimney supports are

used for this function. (Fig. 9)

Chase Installation

A chase is a vertical box-like structure which encloses

the ﬁreplace and/or chimney. Chases are typically built

on the outside of the house with ﬁreplace opening cut

into the outer wall of a room. (Page 5, Fig. 5)

If you need help in determining ﬁreplace location or

how the chimney system should be run, contact your

TEMCO Fireplace Products dealer for assistance.

If you live in a cold climate, it is not required but

highly recommended that you insulate ﬁreplace

enclosure to eliminate cold air penetration as much as

possible.

Insulate base of ﬁreplace with a noncombustible

insulation rated for a minimum of 300°F. Insulating

is very important for outside wall installations over

a concrete slab. If ﬁreplace is installed on a platform,

insulation should be placed on top of the platform

before ﬁreplace is set. (Fig. 10)

When a ﬁreplace is installed in a chase or on a

outside wall, enclosure should be treated like any

outside wall in a home. Insulation should be installed

on the inside wall as well as the outside wall(s). In a

chase, it is also a good idea to install a ﬁrestop at the

ﬁrst ceiling level above the ﬁreplace and enclose the

chase with sheeting material. Insulation may then be

installed above sheeting material to assure the space

around the ﬁreplace is totally protected. (Fig. 5)

When installing the chimney, DO NOT caulk between

outer pipe and ﬁrestop. It is vital that some air be al-

lowed to ﬂow through this very thin gap.

CAUTION: WHEN INSTALLING A FIREPLACE

IN AN INSULATED ENCLOSURE, BE SURE ALL

REQUIRED AIR SPACES ARE MAINTAINED. (Page

14, Figure 20)

FP284

Fig. 9 Chimney support installation

IWF284

MBUF

5/25/96

Chimney Sup-

port Strap

SKCS8

TF/TL Series Woodburning Fireplaces

20007461

FP555

Platform, insulation

11/10/97

5/11/99 djt



Framing

Framing can be constructed before or after the ﬁre-

place is set in place, however, most installers build the

frame before setting the ﬁreplace.

Frame ﬁreplace with 2 x 4 lumber or heavier materials.

Refer to framing dimensions in Figures 1, 2, 3 or 4 for

basic ﬁreplace speciﬁcations.

NOTE: When using 2 x 6 framing construction,

the allowable air space between the front of the

SK8 outer pipe and 2 x 6 framing is reduced to 1"

(25mm) as tested and approved by U.L. for use in

both the United States and Canada.

NOTE: Framing should be positioned to accommodate

wall covering and ﬁreplace facing material.

Installing Electrical Wire

(for Circulator Models)

If a circulating ﬁreplace is to be installed, run the 120

VAC, 60 Hz wiring to the left side of installation. Wiring

must be completed before the ﬁreplace is secured and

ﬁnish material applied.

Remove the cover plate and electrical knock-out on the

lower left side of the ﬁreplace and set aside. Follow the

instructions on Page 10 for proper wiring and installa-

tion of the EB1.

If the fan kit is not being installed with the ﬁreplace, it

is highly recommended that 120 VAC supply be made

available since someone may elect to install a blower at

a later date.

Option For Circulating Models Only —

EB1 (Receptacle) Hook-Up:

• Wiring should be installed by a certiﬁed

electrician.

• Turn off circuit breaker before wiring models.

Once ﬁreplace is secured, complete wiring the fan

kit. Remove knockout in the center of the back of the

EB1 and install listed cable clamps. Feed electrical

wire through listed cable clamp leaving approximately

6" (159mm) of wire exposed through the EB1. Se-

cure listed cable clamp to the wire.

Attach white wire from power source to one (1) wire

of receptacle and secure with nut. Attach black wire

from power source to the other wire of receptacle and

secure with nut. Be sure nuts are secured tightly.

Secure EB1 assembly to inside of electrical box

coverplate using two screws. Attach cover to face of

the EB1 while being careful to position excess wire

completely within the EB1, then attach coverplate to

ﬁreplace.

Install Fan Kit Assembly

Refer to optional Model FK12 fan kit assembly instal-

lation instructions for ﬁeld installation.

Chimney Set-up

Since you have already preplanned the chimney run,

you should know exactly how the installation is to be

accomplished — how much pipe is required, the num-

ber of elbows, if any, and type of termination to be used.

CAUTION: REPORT TO YOUR DEALERS ANY

PARTS DAMAGED IN SHIPMENT, SPECIFICALLY

CHECK THE END CONNECTION OF CHIMNEY SEC-

TIONS AND ELBOWS.

NOTE: Fireplaces may use CFM Corporation Model

SK8, or Model S (three wall) chimney systems. The

TF/TL Series Fireplace will accept the SK8 chimney

system as is; but a TWABR adapter collar is required

when using the Model S (triple wall) chimney system.

The installation procedure described in this manual

applies only to the SK8 system. Either chimney system

may be used, but may not be mixed.

FP555

Fig. 10 Insulating between platform and ﬁreplace.

Hard Flat

Surface

Insulation

Platform

TF/TL Series Woodburning Fireplaces

20007461

Determine offset distance of your chimney arrangement

from centerline of ﬁreplace to centerline of chimney

where it is to pass through ceiling.

Locate center point of the chimney on ceiling as though

a straight up chimney arrangement is to be used. Mea-

sure your offset dimension from straight up chimney

center point on ceiling.

Ceiling Chimney Hole/

Possible Obstructions

The size of the hole in ceiling will vary with the angle at

which the chimney passes through ceiling.

Drive a nail up through ceiling at marked chimney

center point. Go to ﬂoor above and see where hole

will be cut. Check to see where existing ceiling joists

and other possible obstructions are located...i.e. wiring,

plumbing etc... If necessary, re-position chimney and/or

ﬁreplace to avoid obstructions.

Cutting the Hole

Cover ﬁreplace collar opening and cut proper sized

chimney hole in chimney. The SK8 pipe allows you to

run pipe through a typical 16” on center joist without

cutting joists.

Framing the Ceiling Hole

Frame the ceiling chimney hole as shown in Figure

12. It is good practice to use framing lumber that is the

same size as the ceiling joists; this is a requirement at

attic level.

Offset Installation

In order to clear an obstruction, it may be necessary

to offset chimney from vertical. This is accomplished

by using CFM Corporation elbows. Use the 30° Offset

Elbow table on Page 6 to determine proper offset and

parts required.

Each offset requires two (2) elbows. The second elbow

is equipped with support straps. It is very important to

install the second elbow in each offset as close to the

ceiling or support as possible so that the elbow straps

can be secured to framing members to help support the

weight of the chimney.

Straight-Up Chimney Installation

To mark the centerline of the ﬂue, put the ﬁreplace

in ﬁnal position and measure out from the wall: 8¹⁄₄"

(210mm)

Mark a spot on the ceiling directly above the ﬁreplace.

Draw a line parallel to the back wall through this mark.

(Fig. 11)

Using a plumb bob positioned directly over center point

of ﬁreplace ﬂue collar, mark the ceiling to establish the

chimney center point. (Fig. 11)

FP556

BR/BC

LOCATE CENTER LINE

11/10/97

8¹⁄₄"

(210mm)

FP556

Fig. 11 Locate centerline of chimney with plumb line.

Chimney Centerline

Actual Center-

point

Plumb Line

Plumb Bob

Imaginary

Centerpoint

Fig. 12 Typical frame for ceiling chimney hole.

FP551

BR/BC

9/29/97

AB AB

A "SK" Series framing = 14¹⁄₂" X 14¹⁄₂" (368 x 368mm)

B "S" Series framing = 17¹⁄₂" X 17¹⁄₂" (445 x 445mm)

Existing Ceiling

Joists

Ceiling

New Framing

Members

Chimney

Hole

This manual suits for next models

Table of contents

Other Temco Indoor Fireplace manuals

Temco

Temco 36CDVRRN Assembly instructions

Temco

Temco ADF3324N User manual

Temco

Temco TLC39-22 User manual

Temco

Temco ADF3310N-4 User manual

Temco

Temco DV5200N Mounting instructions

Temco

Temco 33TDVN Assembly instructions

Temco

Temco DV5200MB User manual

Temco

Temco ADF36-ST User manual

Temco

Temco DV5200DSN Mounting instructions

Temco

Temco TEF26 Assembly instructions

Temco

Temco DV1000DSN Mounting instructions

Temco

Temco 33 TDVDSN Installation instructions

Temco

Temco Builder Direct Vent 36CDVXRRN Assembly instructions

Temco

Temco 33RDVN Installation instructions

Temco

Temco 41DVDSN User manual

Temco

Temco VF36RN Mounting instructions

Temco

Temco 33RDVDSN Installation instructions

Temco

Temco PVF7400 Series User manual

Temco

Temco TLC42-4 User manual

Temco

Temco DV1000MBN Mounting instructions

Temco

Temco Builder Direct Vent 36CDVXRRN User manual

Temco

Temco DV1000N/P User manual

Temco

Temco TBREF36 Mounting instructions

Temco

Temco PRESTIGE Series User manual

Popular Indoor Fireplace manuals by other brands

Brigantia

Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual

Nordpeis

Nordpeis Bergen Installation and user manual

Superior

Superior BCT2536TMN Installation and operation instructions

Quadra-Fire

Quadra-Fire 5100I-GD-B owner's manual

Renaissance

Renaissance RUMFORD 1000 user manual

Lacunza

Lacunza IV-800 Instruction book

Baxi

Baxi 940 Installer and owner guide

Dru

Dru Maestro 60/2 Tall RCH installation manual

Diamond Fireglass

Diamond Fireglass SS-O22 General assembly, installation, and operation instructions

HearthStone

HearthStone Windsor Bay 8830 Owner's manual and installation guide

Napoleon

Napoleon ASCENT B42 quick start guide

Enviro

Enviro E33GI owner's manual

Smeg

Smeg L30 FABE Installation & user's instructions

KEDDY

KEDDY K700 Installation instructions care and firing instructions

Godin

Godin 3451 manual

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 operating manual

Desa

Desa CCFPDFT Owner's operating & installation manual