Teleview TAV900A User manual
Professional Digital Television Receiver
TLV-300E™, TLV-300E/M™
HDTV Monitor TAV900A
ser’s Manual
Version 2.0 (For FW V2.1.9, FPGA V3.1)
May 11, 2010
Teleview
Corporate Headquarter Teleview, Inc. 355-1 Yatap, Bundang, Seongnam, yeonggi, 463-828, Republic of Korea
E-mail: sales@teleview.com http://www.teleview.com
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
Table of Contents
1. OVERVIEW 7
1.1 Introduction 7
1.2 Delivered Contents 8
1.3 Front Panel Overview 8
1.3.1 Alphanumeric Displa 10
1.3.2 Function Buttons 11
1.3.3 Numeric Buttons 12
1.4 Rear Panel Overview 13
1.4.1 Overview 13
1.4.2 Video Output 14
1.4.3 Audio Output 15
1.4.4 Digital Output BNC Connectors (AES3/DVB-ASI/SMPTE-310M) 15
1.4.5 DVB-ASI/SMPTE-310M Input BNC Connectors 16
1.4.6 RF Input Connectors 16
1.4.7 Communication Port 16
1.4.8 FAULT Output Port 16
1.4.9 Power Switch & Inlet 16
1.5 BNC Configuration 17
2. GETTING STARTED 18
2.1 Initial Hook-up 18
2.2 Verif ing YPbPr or RGB Component Video Output (Onl if applicable displa is attached) 19
2.3 Verif ing SDI Video Output (Onl if applicable displa is connected) 19
2.4 Verif ing Composite Video Output (Onl if applicable displa is connected) 22
2.5 Verif ing 8VSB Digital TV Signal Decoding thru RF Input (Onl if ou have 8VSB RF input available)
22
2.6 Verif ing Digital TV Signal Decoding thru DVB-ASI or SMPTE-310M Input (Onl if ou have this
source available) 23
2.7 Verif ing QAM Digital TV Signal Decoding thru Cable TV Input (Onl if ou have Digital Cable RF
input available) 24
2.8 Verif ing Analog Audio Output 25
2.9 Using DVB-ASI or SMPTE-310M TS Output 25
2.10 Using Digital Audio Output 25
Version 2.0 2
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
2.11 Using FAULT Output 26
2.12 SNMP Network Management 26
2.13 Saving Configuration 26
2.14 Menu Using OSD 26
3. MENU DICTIONARY 28
3.1 Overview 28
3.2 CONFIG Menu 29
3.2.1 CONFIG Menu Overview 29
3.2.2 CONFIG/MAIN sub-menu 30
3.2.3 CONFIG/SUB sub-menu 35
3.2.4 CONFIG/RF-IN1 sub-menu 36
3.2.5 CONFIG/RF-IN2 sub-menu 36
3.2.6 CONFIG/BNC OUT(AES/ASI/SMPTE310M) sub-menu 37
3.2.7 CONFIG/SYSTEM sub-menu 38
3.2.8 CONFIG/NETWORK 39
3.2.9 CONFIG/FAULT OUT sub-menu 40
3.2.10 CONFIG/PRIORITY 41
3.2.11 CONFIG/AUTO SELECTION DELAY: 42
3.2.12 CONFIG/SI MODE 42
3.3 STATUS Menu 42
3.3.1 STATUS/MAIN sub-menu 43
3.3.2 STATUS/SUB sub-menu 46
3.3.3 STATUS/RF-IN1 and STATUS/RF-IN2 sub-menu 47
3.3.4 STATUS/INPUT sub-menu 47
3.3.5 STATUS/VERSION sub-menu 48
3.3.6 STATUS/SERIAL NUMBER sub-menu 48
3.3.7 STATUS/MAC-ADDRESS sub-menu 48
3.3.8 STATUS/LICENSE LEVEL sub-menu 48
3.4 SAVE PROFILE Menu 49
3.5 RECALL PROFILE Menu 49
3.6 AUTO SEARCH Menu 49
3.7 DEFAULT Menu 49
3.8 DIAGNOSIS Menu 52
4. HOW TO UPGRADE FIRMWARE 54
Version 2.0 3
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
4.1 Firmware Upgrade from Teleview Web Site(TELEVIEW URL) 54
4.2 Firmware Upgrade with FTP(TLVFTPD) 54
4.3 Firmware Upgrade with USB Port(USB) 55
5. HELP 56
5.1 Trouble Shooting 56
6. SYSTEM STATUS LOG 57
7. SPECIFICATIONS1 58
8. INPUT AND OUTPUT SIGNAL SPECIFICATIONS2 60
8.1 Audio Output 60
8.2 Main Video Output – Component 61
8.3 Main Video Output – SDI 61
8.4 Sub Video Output –Composite 62
8.5 USB 62
8.6 Ethernet 62
8.7 SMPTE-310M Input 63
8.8 SMPTE-310M Output 63
8.9 DVB-ASI Input 63
8.10 DVB-ASI Output 64
8.11 RF Input 64
8.12 FAULT Output 64
8.13 Power Inlet 65
. FACTORY OPTION 66
9.1 TLV-300E/M option 66
9.2 DVB-T reception option 66
REFERENCES 67
Version 2.0 4
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
IMPORTANT SAFETY INSTR CTIONS:
Important safety instructions shall be provided with each apparatus. These instructions shall be in a
separate booklet or sheet, or be located before any operating instructions in an instruction for
installation or use and supplied with the apparatus. This information shall be given in a language
acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “IMPORTANT SAFETY INSTRUCTIONS”. The
following safety instructions shall be include where applicable, and, when used, shall be verbatim
as follows. Additional safety information is not prohibited from being included by adding statements
after the end of the following safety instruction list. At the manufacturer’s option, a picture or
drawing that illustrates the intent of a specific safety instruction is not prohibited from being placed
immediately adjacent to that safety instruction.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean onl with a dr cloth.
Do not block an of the ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near an heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safet purpose of the polarized or grounding t pe plug. A polarized plug has two blades
with one wider than the other. A grounding t pe plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for our safet . When the provided plug does not fit into our outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularl at plugs, convenience receptacles, and
the point where the exit from the apparatus.
Onl use the attachments/accessories specified b the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in an wa , such as power suppl cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normall , or
has been dropped.
The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
This equipment shall be connected to mains socket outlet with a protective earth connection.
Version 2.0 5
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
CAUTION : TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICIN TO
QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage" within
the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
License Notice:
“Dolby Pro Logic ΙΙ”, and the double-D Symbol are trademarks of Dolby Laboratories. Companies planning to use this
implementation in products must obtain a license from Dolby Laboratories Licensing Corporation before designing such
products.
Version 2.0 6
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
1. OVERVIEW
1.1 INTROD CTION
The Professional Digital Television Receiver TLV-300E/TAV-900A receives digital broadcasting
signal through various sources and supplies demodulated / decoded video and audio in various
industrial forms of signal.
Designed to be compliant with versatile industrial standard such as MPE -II MP@ML/HL[1][2], ATSC
[3] (Advanced Television Systems Committee) and DVB (Digital Video Broadcasting), the TLV-
300E/TAV-900A offers easy connection to various digital televisions and receivers.
The TLV-300E/TAV-900A comes with 8VSB (Vestigial Side Band) and 6MHz 64QAM/256QAM
(Quadrature Amplitude Modulation) reception module for America/Korea terrestrial/cable digital
broadcasting.
The digital broadcasting signal is supported in the forms of DVB-ASI [4], SMPTE-310M[5], or it can
be a radio frequency (RF). The video output is supplied through composite video signal, Y/Pb/Pr
analog video signal with embedded sync and R BHV analog video signal. In addition, it supports
the SDI (Serial Digital Interface) digital video (SMPTE-292M[6] and SMPTE-259M[7]) with embedded
audio (PCM audio) for standard definition and high definition. The audio output can be analog
stereo output and digital AES3-id (Audio Engineering Society Standard 3) output.
The receiver has two sets of video / audio decoder, MAIN channel and SUB channel, working
independently. MAIN channel video output is supplied through YpbPr/R BHV/SDI OUT BNC
connectors and SUB channel video output is supplied through CVBS (composite video baseband
signal) BNC connector. CVBS output works at only 720x480 (576) interlaced mode. The MAIN and
SUB audio output is supplied through L1, R1 and L2, R2 analog audio and AES3-id digital audio for
both channel as well as embedded audio in SDI output.
By supporting SNMP (Simple Network Management), the user can remotely monitor and control
the unit via Ethernet connection. The firmware could be updated easily to recent version via a USB
port and Ethernet. With its slim form factor 1U Rack mountable frame and easy maintenance
method the TLV-300E/TAV-900A can be easily installed and operated.
Version 2.0 7
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
1.2 DELIVERED CONTENTS
When you receive the TLV-300E/TAV-900A from a distributor, the package comes with following
contents:
Table 1 Content in the carton box
Description Quantity
TLV-300E 1RU frame or
TAV-900A 3RU frame
1
AC power cord 1 North America type (Type B) plug and an IEC C13 line socket
or
1 Power cord featuring a CEE 7/4 plug (Type F, Schuko) and an
IEC C13 line socket.
Audio Cable Converter 1 D-sub 9p to XLR cable
User’s manual 1
1.3 FRONT PANEL OVERVIEW
The Front panel of TLV-300E can be divided into 4 main parts:
Table 2 Content in the carton box
1 2 lines by 40 characters alphanumeric character display
2 Function buttons (Arrow, LOCK, ENTER, EXIT)
3 Numeric buttons
4 3 LEDs (POWER, STATUS, FAULT)
Version 2.0 8
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
TLV300E DIGITAL TV RECEIVER
ENTER
EXIT
POWER STAT S FA LT
LOCK
Figure 1 Front Panel View of the TLV-300E Receiver
The Front panel of TLV-900A can be divided into 6 main parts:
Table 3 Front panel components
1 7 inch color TFT-LCD display
2 Two speakers
3 Volume knob
4 Function buttons (Menu, Mute, SLCT(==ENTER), EXIT)
5 Arrow buttons
6 3 LEDs (POWER, STATUS, FAULT)
TAV9 00 A DTV MONITO R
POWER
M EN M TE
STAT S FA LT
SLCT EXIT
VOL M E M IN M AX
Figure 2 Front Panel View of the TAV-900A Receiver
Version 2.0 9
TLV-300E/TAV-900A Professional Digital TV Receiver ser’s Manual
1.3.1 Alphanumeric Display
The status display provides clear viewing of status and menu configuration with 2 lines by 40
characters. It is used to control the TLV-300E directly from the front panel.
.3 2 . 9IF
-
N 1-
B
d
: 4 B-
B 0
B
x
B1
0C 8L
- :
O 8K -10:
-B3:2:
BR V
- : 5
0S
>
< >R :L 2 -R 1 :
Figure 3 Alphanumeric Display
Table 4 Regions in the alphanumeric display
1. Lock State In this upper line of the display, R1:L shows that RF input-1 is in
LOCK state, and R2:- means RF input-2 is in UNLOCK state.
B1:-, B2:-, B3:-, B4:-, and B5:- means BNC input-1~5 is in
UNLOCK state.
In the bottom line of the display, RF-IN1:LOCK 8VSB 32.9dB
0.00x10-8 shows that lock state, modulation system, SNR and
BER value of RF input-1.
User can view the status information of RF-IN2, BNC1~5 by
scolling left/right using <,> arrow buttons.
User can change the INPUT STATUS format into MAIN STATUS
or SUB STATUS using the ^ arrow button.
In the MAIN STATUS, the upper line of the display-MAIN:RF-IN1
shows that MAIN channel is taking input signal from RF-IN1
2. Applicable Button It displays available function buttons for current menu
[ex: ENTER/SLCT (select button); <, >, ^, v (arrow button)]
3. Menu Entries / Status
Bar
It displays sub menus, parameter, or status
Version 2.0 10
1. Lock State 2. Applicable Button
Buttons
3. Menu Entries/ Status Bar
This manual suits for next models
3
Table of contents
Other Teleview TV Receiver manuals
