Teleco FlatSat Elegance User manual
UK Installation manual
Flat Sat Elegance
TABLE OF CONTENTS Page
Information ...............................................................................................................................................1
List of accessories........................................................................................................................................2
Important notice..........................................................................................................................................3
Assembly instructions..................................................................................................................................5
Installation with cables coming out sideways............................................................................................6
Installation with cables through the centre of the base plate....................................................................8
Flat Sat Elegance – Front view....................................................................................................................9
Flat Sat Elegance – Rear view....................................................................................................................9
Flat Sat Elegance Kits...............................................................................................................................10
How to identify your Flat Sat Elegance Kit.................................................................................................10
Complete Kit with Black Box, Sat Decoder and TV.................................................................................11
Connecting the complete Kit with a Sat FORCE HD CI+ receiver and a 19" Teleco United TV......................12
Connecting the complete Kit with a TivuSat DS510M receiver and a 19" Teleco United TV (Italy only)........13
Connecting the complete Kit with a TNT SD M6000 receiver and a 19" Teleco United TV (France only)...14
Connecting the complete Kit with a TNT HD M5200/M7000 receiver and a
19" Teleco United TV (France only)..........................................................................................................15
Kit with Black Box, Sat Decoder without TV...............................................................................................16
Connecting the Kit with a Sat FORCE HD CI+ receiver .........................................................................17
Connecting the Kit with a TivuSat DS510M receiver (Italy only)..................................................................18
Connecting the Kit with a TNT SD M6000 receiver (France only)...........................................................19
Connecting the Kit with a TNTHD M5200/M7000 receiver (France only)...........................................................20
Configuration without Kit – connection diagram........................................................................................21
LNB rotation for ideal signal reception in extreme areas in Europe........................................................22
Installation tips...........................................................................................................................................23
Technical specifications..............................................................................................................................23
Spare parts tables.....................................................................................................................................24
Kit labels.................................................................................................................................................34
Information
Congratulations on your purchase! Flat Sat Elegance is among the most technologically
advanced products in the field of satellite TV reception. This handbook has been prepared
to provide information on the technical specifications and how to install, use and maintain
your Flat Sat Elegance system:
For additional information, please contact your local dealer or directly the manufacturer:
TELECO s.p.a.
Via E. Majorana 49
48022 LUGO (RA)
Web site: www.telecogroup.com
After-sales service: 899.899.856
TELECO s.p.a. declines all responsibility for any errors contained in this manual.All information
contained herein is up to the date of printing and the above-mentioned revisions. TELECO
s.p.a. reserves the right to make any changes made necessary by the development of its
products.
1
List of accessories
Flat Sat Elegance is delivered inside a cardboard case that has been specially made to
protect it from knocks and pressure. The following accessories are supplied:
1 External motor-driven unit
2 65-85 cm dish
3 Universal LNB
3 SKEW (OPTIONAL)
4 Black Box
5 MIR remote control expander
6 Motor Connection Cable
7 Antenna/Black Box Connection Lead
8 Power Supply Cable
9 Remote Control
10 Waterproof box to pass leads through
11 Heat-shrinking sheaths
12 Roof attachment plate
13 No. 4 Locknuts M6
14 No. 4 Screws and Locknuts - M6
15 User’s manual and installation manual
16 Jack-Jack lead 0.5 m
16 Jack-Jack lead 2.0 m
2
Important notice
Flat Sat Elegance is packaged in two separate cartons for transport reasons:
a) the first package contains the driving unit with all the cables, and the Black Box;
b) the second package only contains the dish.
• It is important to check that the dish has not been damaged during transport when
the package is opened. In particular, check the following carefully:
• By resting the dish edge against a flat surface (e.g. the floor or a wall) check that it makes
contact to the surface all around. If it is not so, try and make the edge level, without denting
the dish, or call our After-Sales Service.
• After checking that everything is in order, install the dish on the driving unit as follows:
1) Temporarily connect the Black Box to the Driving unit via the grey motor cable.
2) Connect the Mir remote control expander to the "IR BLACK BOX" connector in the
Black Box.
3) Power the Black Box using a battery.
4) Press the System ON-OFF button on the remote control and wait (about 30 seconds)
for the dish support mast to rise.
5) Once you have reached the desired position, disconnect the power supply cable to
switch off the Flat Sat Elegance.
6) Secure the dish to the mast and screw down the four supplied screws.
7) Turn the unit on again and wait for the antenna to close.
8) Disconnect the Black Box, the battery and install the driving unit on the vehicle.
Recycling: with a view to reducing disposal of waste electrical and electronic
equipment as much as possible, do not throw out this appliance, once it has
reached the end of its life, together with other unsorted municipal waste, but make
use of a recycling centre.
YES NO
3
Assembly instructions
1) Position the Black Box in an easy accessible, ventilated compartment.
2) On the roof of the vehicle, choose a free area large enough to allow the antenna to
revolve (Fig. 2).
3) Install the connection cables (Grey and White) until you reach the powered OUTSIDE
UNIT installation area.
4) Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in.
5) Remembering that the OUTSIDE UNIT must be fastened as shown on Fig. 3, remove
the BASE PLATE from the outside unit, unscrewing all 4 nuts.
6) Position the base plate as shown on Fig. 4, with the short side towards the driving
direction of the vehicle.
2
1
Flat Sat Elegance
650 - 140 cm
Flat Sat Elegance 850
- 160 cm
Driving direction
of the vehicle
4
5
When they are present, remove the transparent films from the BASE PLATE (Fig. 5).
7) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the
whole surface (e.g. SIKAFLEX).
8) Fasten the BASE PLATE to the roof (short side towards the vehicle driving direction),
now fasten the external powered unit to the four stud bolts of the plate, using the four
nuts supplied with the equipment.
Caution: to ensure ideal nut tightening and prevent possible pin breaks, tighten
the nut with a torque wrench set to 8 Newtons/metre
Driving direction
of the vehicle
9) Apply a layer of silicone all around the BASE PLATE in order to make it completely
waterproof (Fig. 5A)
5 5A
4
3
Driving direction
of the vehicle
8
6
12)Accomodate the cables into a protection raceway up to the point where the cables go
into the vehicle, using the suitable supplied fairlead.
9) Seal the fairlead
carefully so as to
prevent any
infiltration by water
Installation with cables coming out sideways
10) Fasten the OUTSIDE UNIT on the base plate and lead the two cables through any of the 4
existing grooves, according to the position as shown on Fig. 6.
WARNING: When performing this operation, do not draw the two cables forcefully, as this might pull
them out.
6
Connection with extension
11) Connect the two cables coming from the centre of the OUTSIDE UNIT to the two supplied
extensions, waterproofing the connectors using the two pieces of heat-shrinking tube.
7
WARNING The Grey and White cables coming
out of the Outside Unit are generally long enough
to allow for connection to the Black Box. If it is
not so, use the extension cables and perform
the following operations:
Installation with cables through the centre of the base plate
WARNING The Grey and White cables coming out of the Outside Unit are generally long
enough to allow for connection to the Black Box. If it is not so, use the extension cables and
perform the following operations:
Connection with extension
13)Connect the Grey and White extension cables, coming from inside the vehicle (Fig. 10)
to the two cables of the outside unit, waterproofing them using two pieces
of HEAT-SHRINKING TUBE (Fig. 11).
WARNING When performing this operation, do not draw the cables coming from the centre
of the outside unit forcefully, as this might pull them out.
7
10
12
11
14)Install the OUTSIDE UNIT on the base plate, remembering that:
a) The right position is the one shown on (Fig. 13)..
b) Apply an abundant layer of silicone on both the base plate and the bottom of the driving
unit so as to prevent any infiltration by water. Screw down the 4 supplied nuts
by the screws and tighten properly (Fig. 15).
15
13
14
8
9
Flat Sat Elegance – Rear Black Box View
1) F type connector – input from LNB converter of the driving unit
2) F type connector – signal output to be connected to any satellite receiver
3) B type USB connector – connection to a PC for updating purpose
4) Connector for connection to the driving unit
5) Diagnostics button (for technical staff only)
6) Connector for power supply input from battery and safety cable
7) 5 A blade fuse
8) SCART connector – TV output
9) SCART connector – Decoder input
10) Jack Connector - Decoder (for Kit configuration only)
11) Jack Connector - TV (for Kit configuration only)
12) Connector for MIR Remote Control Expander
1
2
3 4 5
7
8
910
6
11
12
1) Power-on indication LED
1
Flat Sat Elegance – Front Black Box View
Table of contents
Other Teleco Satellite TV System manuals
