Tektronix PRISM MPI2-10 Programming manual
MPI2-10 Front Panel Assembly Installation Instructions
CAUTION. Replacement of the front-panel assembly should be performed only by
qualified personnel. The instrument hardware can be damaged performing this
procedure.
Servicesafetysummary
The Service safety summary section contains additional information required to
safely perform service on the product. Read this Service safety summary before
performing any service procedures.
To avoid electric shock. Do not touch exposed connections.
Do not service alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect power. To avoid electric shock, switch off the product power and
disconnect the power cord from the mains power before removing any covers or
panels, or opening the case for servicing.
Use care when servicing with power on. Dangerous voltages or currents may exist
in this product. Disconnect power, remove battery (if applicable), and disconnect
test leads before removing protective panels, soldering, or replacing components.
Verify safety after repair. Always recheck ground continuity and mains dielectric
strength after performing a repair.
Terms in this manual
These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
www.tek.com
Copyright © Tektronix
*P075110800*
075-1108-00
MPI2-10 Front Panel Assembly Installation Instructions
Kit parts list
The following table lists the parts that are supplied with the front panel assembly
installation kit.
Quantity Part Number Description
1 850-0336-XX FRONT PANEL ASSY
4 211-0734-XX SCREW, MACHINE; 6-32 X 0.250, FLH100, STEEL, ZINC
FINISH,T-10TORXDR
1 075-1108-XX PRISM FIELD UPGRADE INSTRUCTIONS
Recommended tool list
Table 1: Recommended tool list
Name Description
Screwdriver handle Accepts Torx-driver bits
T-10 TORX tip Used for removing instrument screws.
TORX-driver bit for T-10 size screw heads.
Torque driver Used to apply precisely a specific torque to
a fastener.
Remove and replace the front panel assembly
These instructions are for personnel who are familiar with servicing the product.
Contact your nearest Tektronix, Inc., Service Center or Tektronix Factory Service
for installation assistance.
WARNING. Dangerous voltages may be present. To prevent electrical shock,
disconnect the power cord from the unit before starting the upgrade procedure.
Failure to do so could cause serious injury or death.
CAUTION. Many components within the instrument are susceptible to static-static
discharge damage. To prevent static discharge damage, service the product
only in a static-free environment. Observe standard handling precautions for
static-sensitive devices while installing this kit. Always wear a grounded wrist
strap, grounded foot strap, and static resistant apparel while installing this kit.
2 MPI2-10 Front Panel Assembly Installation Instructions
MPI2-10 Front Panel Assembly Installation Instructions
1. Set the instrument so that the bottom is down on a static-free work surface.
CAUTION. Dislodging or cracking the bezel can cause damage to the display. To
prevent damage to the display, do not put excessive pressure on the bezel when
removing, replacing or installing modules.
2. Remove the top cover as follows:
a. Use a TORX-driver with a T-10 TORX tip to remove the twelve screws
securing the cover to the instrument.
b. Slide the cover back and then lift it from the back to remove it from the
instrument; set the cover aside.
3. UseaTORXdriverwithaT-10TORXtiptoremovethetwoscrewsoffeach
side of instrument.
MPI2-10 Front Panel Assembly Installation Instructions 3
MPI2-10 Front Panel Assembly Installation Instructions
4. Tip the instrument up on the back panel and pull the Display up until the
connector is disconnected.
5. To reinstall the display, reverse the steps.
CAUTION. The touch display will not operate correctly if connector is not lined
up. To avoid this issue, line up the connectors before engaging.
4 MPI2-10 Front Panel Assembly Installation Instructions
Other manuals for PRISM MPI2-10
1
Table of contents
Other Tektronix Test Equipment manuals
Tektronix
Tektronix 2465A User manual
Tektronix
Tektronix P6248 User manual
Tektronix
Tektronix TDS3000B Series User manual
Tektronix
Tektronix P6101B User manual
Tektronix
Tektronix TBS1000C Series User manual
Tektronix
Tektronix MSO2000B Series Manual
Tektronix
Tektronix 585 User manual
Tektronix
Tektronix 7B53A User manual
Tektronix
Tektronix 222 User manual
Tektronix
Tektronix 80A07 User manual
Tektronix
Tektronix 7854 User manual
Tektronix
Tektronix TDS5000B Series Use and care manual
Tektronix
Tektronix DSA8200 Series Operating and maintenance manual
Tektronix
Tektronix 2252 User manual
Tektronix
Tektronix TDS 310 User manual
Tektronix
Tektronix 323 User manual
Tektronix
Tektronix ths3000 series User guide
Tektronix
Tektronix TAS 465 User manual
Tektronix
Tektronix 7B70 User manual
Tektronix
Tektronix TDS 620 User manual
