Tektronix WFM6100 Opt. MB User manual

Instructions

WFM61UP FP, WFM70UP FP, and WFM71UP FP

Front Panel Upgrade

WFM6100, WFM7000, and WFM7100

Waveform Monitors

075-0948-00

*P075094800*

075094800

Warning

The servicing instructions are for use by qualified

personnel only. To avoid personal injury, do not

perform any servicing unless you are qualified to

do so. Refer to all safety summaries prior to

performing service.

www.tektronix.com

suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes

that in all previously published material. Specifications and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

HIn North America, call 1-800-833-9200.

HWorldwide, visit www.tektronix.com to find contacts in your area.

WFM61UP FP, WFM70UP FP, and WFM71UP 1

Service Safety Summary

Only qualified personnel should perform service procedures. Read this Service

Safety Summary before performing any service procedures.

Do Not Service Alone. Do not perform internal service or adjustments of this

product unless another person capable of rendering first aid and resuscitation is

present.

Disconnect Power. To avoid electric shock, switch off the instrument power, then

disconnect the power cord from the mains power.

Use Care When Servicing With Power On. Dangerous voltages or currents may

exist in this product. Disconnect power, remove battery (if applicable), and

disconnect test leads before removing protective panels, soldering, or replacing

components.

To avoid electric shock, do not touch exposed connections.

Service Safety Summary

2WFM61UP FP, WFM70UP FP, and WFM71UP

WFM61UP FP, WFM70UP FP, and WFM71UP 3

Kit Description

This document describes replacing the waveform monitor front panel with the

new, upgraded front panel. One very obvious change is the number of buttons on

the front panel; there are many more buttons on the new front panel. This is

necessary because the new front panel does not employ a touch-screen interface;

all control is through the front panel buttons. Among other things, this change

provides a noticeable improvement in instrument front panel response.

Products

WFM6100 All

WFM7000 All

WFM7100 All

Minimum Tool and Equipment List

Required tools and equipment Part number

PC with USB port -- -- -- -- -- -- -- -- -- --

Network connection ---------- ----------

Torque screwdriver handle Standard tool

T-10 TORX bit Standard tool

Kit Parts List

Quantity Part number Description

1Each 614--1044--xx FRONT PANEL ASSY

1 Each 063--4072--xx USB FLASH DRIVE, PROGRAMMED

1Each NS OPTION KEY LABEL

1 Each 075--0948--00 UPGRADE KIT INSTRUCTIONS (THIS DOCUMENT)

1Each NS IMPORTANT DOCUMENTS ENVELOPE

1Each 071-2191-01 MANUAL, TECH; SVCPT--UPG; TEKTRONIX SUPPLE-

MENTAL INFORMATION SHEET FOR THE PEOPLES

REPUBLIC OF CHINA; CHINA ROHS

NS - Not Saleable

Kit Description

4WFM61UP FP, WFM70UP FP, and WFM71UP

WFM61UP FP, WFM70UP FP, and WFM71UP 5

Installation Instructions

These instructions are for personnel who are familiar with servicing the product.

If you need further details for disassembling or reassembling the product, refer to

the appropriate product manual. Contact your nearest Tektronix, Inc., Service

Center or Tektronix Factory Service for installation assistance.

CAUTION. To prevent static discharge damage, service the product only in a

static-free environment. Observe standard handling precautions for static-sensi-

tive devices while installing this kit. Always wear a grounded wrist strap,

grounded foot strap, and static resistant apparel while installing this kit.

These instructions will guide you through the following steps:

HUpdate the software

HConnect the waveform monitor to the network, if not already connected

HObtain the waveform monitor IP address

HVerify the network connection

HObtain the waveform monitor software version

HUpdate the software

HReplace the front panel

HRemove the top cover

HRemove the fan bracket (optional)

HRemove the front panel/LCD assembly

HInstall the new front panel/LCD assembly

HReplace the fan bracket

HReplace the top cover

HApply the instrument model label

HVerify Operation

HCheck waveform monitor IP address; it may have changed

HUpdate the Installed Options

Installation Instructions

6WFM61UP FP, WFM70UP FP, and WFM71UP

Update the Software

Before installing the new front panel assembly, you must first update the

instrument software, located on the USB Flash Drive included in this kit.

These instructions are written for a PC running Windows XP.

NOTE. If a notebook computer is used, make sure it has a full battery charge or

is connected to an AC power source.

If the PC and the waveform monitor are already network connected, go to

Obtain waveform monitor IP address,onpage7.

NOTE. Do not reboot the instrument after updating the software. Disconnect the

power cord and proceed with the front panel replacement.

To allow network access to the instrument, you need to set the IP address.

Network addresses can be assigned either automatically or manually. If your

network does not use DHCP, you will have to manually enter the address for the

instrument. To get an address, talk to your LAN administrator.

1. Verify that the waveform monitor is connected to the network.

2. Power on the waveform monitor.

3. Press the MAIN button to display the Main menu, and then touch the

Config soft key to display the Configuration submenu.

4. Touch the Utilities soft key, and then the Communications soft key.

5. Touch the Config Mode soft key, and then set the Config Mode to Manual

or DHCP, depending on your network setup.

Selecting the configuration mode will close the Config Mode submenu.

6. Touch the Network Setup soft key.

a. Select Enabled under Remote Control Port.

b. Select Enabled under Remote Web Interface.

7. If you can’t use DHCP you will have to set the IP Address, subnet mask, and

gateway address network parameters in the Network setup menu; see your

LAN administrator for the required values. (Be sure to use compatible

addresses between the PC and the monitor.)

8. Press the Close soft keys to close the submenus.

Network Connection and

IP Settings

Installation Instructions

WFM61UP FP, WFM70UP FP, and WFM71UP 7

These steps assume the instrument has already been configured for network

connection as described previously, and guided by a network administrator.

1. Press the MAIN button, then touch the Config softkey.

2. Touch the Utilities, then the Communications, and the Network Setup

softkeys.

3. Make a note of the waveform monitor’s IP address. You will need that in the

next procedure.

NOTE. If you are using DHCP and the waveform monitor did not receive an IP

address, go back through steps 3 through 5 of the Network Connection and IP

Settings procedure, change the waveform monitor to Manual, and then change it

back to DHCP.

If the waveform monitor still does not receive an IP address, cycle the power

while in DHCP mode.

4. Touch OK to close the network setup window.

1. On the PC, select Start >All Programs >Accessories >Command

Prompt.

2. Change to drive C:\ by typing cd c:\ in the command window, and then press

the Enter key.

3. In the command window, type ping, followed by the waveform monitor’s IP

address, and then press the Enter key. For example: ping 192.168.1.2.

4. Check that the replies that appear on the PC resemble the following:

Pinging 192.168.1.2 with 32 bytes of data:

Reply from 192.168.1.2: bytes=32 time=2ms TT =63

Reply from 192.168.1.2: bytes=32 time=1ms TT =63

Ping statistics for 192.168.1.2:

Packets: Sent = 4, Received = 4, ost = 0 (0% loss),

Approximate round trip times in milli-seconds:

Minimum = 1ms, Maximum = 2ms, Average = 1ms

If there are no replies, check your network connections and verify that the

waveform monitor settings and PC settings are correct.

Obtain waveform monitor

IP address

Verify the network

connection

Installation Instructions

8WFM61UP FP, WFM70UP FP, and WFM71UP

In this procedure, you load the Upgrade Assistant file into the PC, check the

waveform monitor software version, and run the Upgrade Assistant.

1. Find the plastic bag in the upgrade kit that contains the USB Flash Drive and

the Option Key label, and plug the Flash Drive into a USB port on the PC.

2. Create a folder on your PC. Name the folder something easy to remember,

like “c:\wfmupgrade”.

3. Copy the file WfmUpgrade.exe from the USB Flash Drive into the directory

created in step 2.

CAUTION. DO NOT just unplug the USB Flash Drive from the PC. This can

erase the files and/or damage the USB Flash Drive.

4. Unmount the USB Flash Drive, using one of the following methods:

HYou can use the Safely remove hardware icon, on the taskbar:

Left-click the icon and select the Safely remove USB Mass Storage

Device -- Drive (x) button that appears. Wait until the Safe To Remove

Hardware message appears before removing the USB Flash Drive from

the USB port.

HOr, you can open My Computer, right-click on the drive with the USB

Flash Drive, and select Eject. Wait for the light to go out on the Flash

Drive before removing it from the USB port.

5. On the waveform monitor, press the MAIN button, then touch the Config

--Utilities andthentheView Hw/Sw Version softkeys. Make a note of the

software version (1.1, 1.23, or 1.25).

6. Touch OK to close the HW/SW version display.

NOTE. You will need to identify whether your software is Version 1.1 or if it’s a

later version, in step 12.

7. Plug the same USB Flash Drive, included in the upgrade kit, into the

waveform monitor USB port.

8. On the PC, select Start >All Programs >Accessories >Command

Prompt to open the Command Prompt window.

9. On the PC, change the directory to the directory created in step 2. For

example, type cd c:\wfmupgrade in the Command Prompt window and

press the Enter key to change to the c:\wfmupgrade directory.

Update the software

Other manuals for WFM6100 Opt. MB

This manual suits for next models

Table of contents

Other Tektronix Monitor manuals

Tektronix

Tektronix WFM2300 How to use

Tektronix

Tektronix WFM2200 Use and care manual

Tektronix

Tektronix MTM400A Use and care manual

Tektronix

Tektronix WFM2200 How to use

Tektronix

Tektronix WFM601 User manual

Tektronix

Tektronix WFM6100 Opt. MB Manual

Tektronix

Tektronix 4112 User manual

Tektronix

Tektronix RFM300 Installation and maintenance instructions

Tektronix

Tektronix WFM7200 User manual

Tektronix

Tektronix 1730 Series User manual

Tektronix

Tektronix WFM90D User manual

Tektronix

Tektronix WFM5200 series How to use

Tektronix

Tektronix WFM2200 Installation and operating manual

Tektronix

Tektronix 1741C Use and care manual

Tektronix

Tektronix WFM700 Series User manual

Tektronix

Tektronix DF 1 Assembly instructions

Tektronix

Tektronix 608 User manual

Tektronix

Tektronix WFM6100 Opt. MB Manual

Tektronix

Tektronix WFM6120 How to use

Tektronix

Tektronix WFM6100 Opt. MB Use and care manual

Tektronix

Tektronix QAM400A Use and care manual

Tektronix

Tektronix WFM7020 Manual

Tektronix

Tektronix WFM6120 Use and care manual

Tektronix

Tektronix AMM768 User manual

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual