Tektronix TG700 User manual

TG700 TV Signal Generator Platform

Module Installation

ZZZ

Instructions

www.tektronix.com

*P075098602*

075-0986-02

or suppliers, and are protected by national copyright laws and international treaty provisions.

Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication

supersedes that in all previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Table of Contents

Introduction ......................................................................................................... 1

Standard Accessories.......................................................................................... 1

Firmware Upgrade.................................................................................................. 2

Equipment Required........................................................................................... 2

Mainframe Memory Requirements .......................................................................... 3

Upgrade Procedures ........................................................................................... 4

Firmware Version Check...................................................................................... 9

Installation Instructions........................................................................................... 10

Preventing Component Damage ............................................................................ 10

Installing a Module ........................................................................................... 11

Entering the Option Key (SDI7 Option 3G only) ......................................................... 13

Removing a Module.......................................................................................... 15

はじめに.................................................................................................. 17

スタンダード・アクセサリ ............................................................................ 17

ファームウェアのアップグレード ........................................................................ 18

必要な機器.......................................................................................... 18

メインフレームのメモリ要件......................................................................... 19

メモリ増設方法 ...................................................................................... 20

ファームウェア・バージョンの確認 ................................................................. 25

取り付け方法 ............................................................................................ 26

コンポーネントの損傷を避けるには ............................................................... 26

モジュールの取り付け .............................................................................. 27

オプション・キーの入力（SDI7 型モジュール、オプション 3G 型のみ）.......................... 30

モジュールの取り外し .............................................................................. 32

TG700 Module Installation i

Table of Contents

ii TG700 Module Installation

Introduction

These instructions provide the installation procedure for the generator and special

function modules for the TG700 mainframe. These instructions also provide the

ﬁrmware upgrade procedure for the TG700 mainframe.

These instructions are composed of the following sections:

Firmware Upgrade describes how to upgrade the ﬁrmware of the TG700

mainframe.

Installation Instructions describes how to install and remove modules from

the TG700 mainframe.

Entering the Option Key (SDI7 OPtion 3G only) describes how to enter the

option key that is required to enable Option 3G on the SDI7 module.

For detailed information about module features and speciﬁcations, refer to the

TG700 TV Signal Generator Platform User Manual and the TG700 TV Signal

Generator Platform Speciﬁcations and Performance Veriﬁcation Technical

Reference included on the TG700 CD-ROM.

Standard Accessories

The following accessories are shipped with each module:

TG700 TV Signal Generator Platform Module Installation Instructions,

Tektronix part number: 075-0986-XX

TG700 Signal Generator Platform Software Library CD-ROM, Tektronix

part number: 020-2721-XX

TG700 Module Installation 1

Firmware Upgrade

This section describes how to upgrade the ﬁrmware of the TG700 mainframe.

You do not need to upgrade the instrument ﬁrmware if the ﬁrmware version

ontheCD-ROMprovidedwiththiskitisthesameastheﬁrmware version

already installed on your TG700 mainframe. In this case, proceed to Installation

Instructions. (Seepage10.)

CAUTION. If the ﬁrmware version of the CD-ROM provided with this kit is later

than the ﬁrmware version installed on your TG700 mainframe, be sure to upgrade

the ﬁrmware of the mainframe before installing the module.

Equipment Required

The following equipment is required to upgrade the ﬁrmware:

PC with Windows 2000/Vista/XP/7 and Ethernet interface installed

10 BASE-T Ethernet cable (crossover or straight)

TG700 Signal Generator Platform Software Library CD-ROM provided with

the new module

2TG700 Module Installation

Firmware Upgrade

Mainframe Memory Requirements

With software version 5.6, the TG700 mainframe must have at least 32 MB of

memory installed. If you intend to install frame picture ﬁles (*.pic), created by the

Frame Picture Generator application for the DVG7, HDVG7, AVG7, or AWVG7

modules, or if you intend to install bitmap frame picture ﬁles (*.bmp) for the SDI7

module, then the mainframe must have 64 MB of memory installed.

Software Upgrades If your existing mainframe has 32 MB of memory and you have loaded the TG700

memory with frame picture ﬁles, you may not be able to upgrade the instrument to

software version 5.6.

If you receive a memory error while attempting to upgrade the software version,

you need to either delete some of the frame picture ﬁles or upgrade your

instrument to 64 MB of memory.

Memory Upgrades Option FP provided extra memory, which allowed the TG700 mainframe to

support the Frame Picture Generator application. This option is no longer

necessary for new TG700 mainframes.

If you have an older mainframe with less than 64 MB of memory, you can increase

the memory in your mainframe to 64 MB by ordering the following upgrade kit:

040-1698-xx. Contact your local Tektronix representative for more information.

TG700 Module Installation 3

Firmware Upgrade

Upgrade Procedures

NOTE. Refer to Mainframe Memory Requirements before you perform the

upgrade procedures. (See page 3.)

Perform the following procedure to upgrade the ﬁrmware. It is not necessary to

uninstall the earlier version.

1. If you are connecting the TG700 directly to a PC:

a. Using a crossover Ethernet cable, connect between the 10 BASE-T port

on the TG700 and the Ethernet port or NIC on the PC.

b. Power on the TG700 and the PC.

c. Identify the PC’s IP address and subnet mask.

NOTE. You can ﬁnd the PC’s IP address and subnet mask by bringing up the

“Command Prompt”, using the “Startup” menu under “Accessories” and

typing “ipconﬁg” at the prompt.

d. Set the IP address of the TG700 such that all the digits are the same except

for the last digit, which should be changed by 1.

e. Set the subnet mask of the TG700 to the same subnet as the PC.

f. Proceedtostep4.

4TG700 Module Installation

Firmware Upgrade

2. If you are connecting the TG700 to your local Ethernet network using a

static IP address:

CAUTION. Using an IP address that is already in use can cause network conﬂicts,

resulting in system instability and/or the system locking up. Ensure that the IP

address is not already in use before connecting to the network. Contact the

network administrator for assistance.

a. Power on the TG700.

b. Set the IP address of the TG700 as speciﬁed by the network administrator.

c. Set the subnet mask of the TG700 as speciﬁed by the network

administrator.

d. Using a straight Ethernet cable, connect between the 10 BASE-T port

on the TG700 and the Ethernet hub port of your local network. By

connecting to an Ethernet network, you can access the TG700 using any

PC on the network.

e. PoweronaPCconnectedtothenetworkandproceedtostep4.

3. If you are connecting the TG700 to your local Ethernet network using a

DHCP server (dynamically allocated IP addresses):

a. Power on the TG700.

b. Set the NET SETUP:DHCP setting to Enable on the TG700.

c. Power off the TG700.

d. Using a straight Ethernet cable, connect the 10 BASE-T port on the

TG700 to the Ethernet hub port of your local network. By connecting to

an Ethernet network, you can access the TG700 using any PC on the

network.

e. Power on the TG700 and a PC connected to the network.

f. Identify the IP address assigned to the TG700 by the DHCP server.

g. Proceed to step 4.

TG700 Module Installation 5

Firmware Upgrade

4. Insert the TG700 Signal Generator Platform SW Library and Documentation

CD−ROM provided with the new module into the CD drive on your PC.

5. When the Product Software and Documentation Browser window appears,

select the Mainframe and Module Software link.

6. Select one of the following upgrade options:

SelectUpgrade to V5.X if your mainframe has 32 MB or more of memory.

Select Upgrade to V4.1 if your mainframe has 16 MB of memory.

The PC will open a Windows Explorer window displaying the contents of

the selected upgrade folder.

NOTE. With software version 5.6 and later, it is strongly recommended that

the TG700 mainframe have 64 MB of memory if you intend to install logo

and/or frame picture ﬁles into a DVG7, HDVG7, or SDI7 module. (See page 3,

MainframeMemoryRequirements.)

6TG700 Module Installation

Other manuals for TG700

Table of contents

Other Tektronix Inverter manuals

Tektronix

Tektronix TG700 Use and care manual

Tektronix

Tektronix PPG3000 Series Installation and maintenance instructions

Tektronix

Tektronix AFG1022 Manual

Tektronix

Tektronix AWG710 User manual

Tektronix

Tektronix PFG 5505 User manual

Tektronix

Tektronix AFG1000 Series User manual

Tektronix

Tektronix SG 503 User manual

Tektronix

Tektronix 2707 User manual

Tektronix

Tektronix AFG3011C User manual

Tektronix

Tektronix B020000 User manual

Tektronix

Tektronix Tektronix SPG8000 Use and care manual

Tektronix

Tektronix CFG250 User manual

Tektronix

Tektronix PG 506 User manual

Tektronix

Tektronix AFG31000 Series Installation and maintenance instructions

Tektronix

Tektronix SPG 422 User manual

Tektronix

Tektronix AFG2021 Use and care manual

Tektronix

Tektronix TG700 Owner's manual

Tektronix

Tektronix MTS4SAV3 User manual

Tektronix

Tektronix AWG 2040 User manual

Tektronix

Tektronix AWG5200 Series Manual

Tektronix

Tektronix RTX100A User manual

Tektronix

Tektronix SPG700 User manual

Tektronix

Tektronix MTG100, MTG300 User manual

Tektronix

Tektronix AFG31000 Series Use and care manual

Popular Inverter manuals by other brands

Fourgroup

Fourgroup Easy use and Programming Handbook

Velleman

Velleman PI300M user manual

Sungrow

Sungrow SG350HX-US user manual

WilTec

WilTec 61897 Operation manual

SMA

SMA SUNNY BOY STORAGE 2.5 Quick reference guide

Simplicity

Simplicity LANDLORD 316 product manual

Santak

Santak SMAX 3000 user manual

ATON

ATON RA.Store-3 user manual

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ operating instructions

Champion

Champion 200989 Operator's manual

Vanner

Vanner 20-500 Series owner's manual

GE GEP user manual

Astrel Group

Astrel Group Power Reducer Installation and instruction manual

MULTIQUIP

MULTIQUIP GDP-5H Operation and parts manual

GoWISE

GoWISE PS1007 user manual

Promate

Promate PM13500D ES Operator's manual

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM user manual

Mitsubishi Electric

Mitsubishi Electric FR-A7AZ instruction manual