Teko Astra-515 ver.A User manual

Other teko Security Sensor manuals

Popular Security Sensor manuals by other brands

THORLABS

THORLABS PDA10JT user guide

Waeco

Waeco UV-DETECT operating manual

Intermatic

Intermatic IOS-DSIMF manual

urmet domus

urmet domus 1083 manual

Siemens

Siemens AZL66 Series manual

BTI

BTI Profiline Multi Finder operating instructions

Challenger

Challenger SL01 instruction manual

DMP Electronics

DMP Electronics 1122INT installation guide

Rielta

Rielta Ladoga MK-RK installation guide

Mirion Technologies

Mirion Technologies ACCURAD PRD user manual

Bosch

Bosch DS835 installation instructions

DBI SALA

DBI SALA EZ Stop User instruction manual

Lamptime

Lamptime ST05C instructions

Ubiquiti

Ubiquiti MFI-MSC quick start guide

Subsite

Subsite 910R Support

Satel

Satel OPAL Pro manual

Aleph

Aleph XC-1XTEU manual

Pima

Pima LARIS QUAD installation instructions

Astra-515 ver. A

Optic-Electronic PIR Motion

Detector

(Volumetric Lens)

User Guide

Manufacturer:

ZAO NTC TEKO

420108 Kazan, Russia

Gafuri 71

+7 843 528-03-69

[email protected]

www.teko.biz

Made in Russia Rev. 515-av1_6_instr_en

1 FUNCTION

Detector is intended to detect unauthorized

access into enclosed protected area and

generate alarm notification by opening of

signaling relay contacts.

2 DETECTION ZONE

3 SPECIFICATION

Range of detectable

moving speed, m/sec .............from 0.3 up to 3.0

Power supply voltage, V.............from 8 up to 15

Current consumption, mA, max..................... 15

Overall dimensions, mm.................... 86×54×41

Operating Conditions

Temperature range, °С............... from 0 to + 50

Relative air humidity, % ......... up to 95 at + 35 °С

Withoutmoisture condensation

4 DELIVERY SET

Delivery set includes: bracket - 1 pcs., label –2

pcs.

5 MODES OF OPERATION

Plug

name

Jumper

position

High detectability

Normal

detectability

Sens

Indication OFF

Indication ON

Ind

6 INSTALLATION PLACE

1) Recommended installation height is 2.4-2.5 m.

2) Install detector on bearing walls and carri-

ers.

3) Alarm loop and power supply wires should

be located far from power cables.

To eliminate false alarm hazards

It is recommended to close all doors, air-vents,

switch off fans, air-conditioners and other

sources of intense air flows in the room during

protection period.

Not recommended installation locations

7 INSTALLATION PROCEDURE

1) Remove cover

2) Remove PCB

3) Select installation

method 4) or 5)

4)Installation on the

wall

5) Installation in the

corner using bracket

6) Insert PCB and

perform wiring (see

sec.8)

7) Perform TEST-pass (see sec.9)

8 WIRING

Perform wiring to detector`s terminals in

accordance with control panel operating manual.

RELAY –terminals for detector connection to

alarm loop;

+12V, GND –power supply terminals.

9 TEST-PASS

1) Remove jumper from Ind plug. Install jumper

on Sens plug.

2) Close detector.

3) Power detector ON. LED starts flash during

60 sec.

4) To detect sensitive zones carry out TEST-

pass in the secured zone

with the speed of 0,3 m/sec.

Stop upon detection

(indicator lights up for 2sec),

mark position, then make a

step back and continue

moving forward.

Repeat TEST-pass inversely.

10 WARRANTY

The operation warranty period is 5 years from

the date of operation start-up but no longer than

5 years 6 months from the date of manufactur-

ing subject to the requirements of Operating

Manual.