Tek Division Minion 2.0 User manual

TEKDIVISION S.R.O.

MinioN 2.0

Personal vaporizer

User manual

Let’s get started.

1. Insert battery

Remove top cap whit negative contact screw. Insert battery. !!! Mind the polarity!!! Positive

facing down.

Put everything back together. Don’t over stress the thread on negative contact screw.. It’s not

necessary. Insert atomizer in 510 connection. 510connection has adjusting screw for 360°

adjusting capability . You can adjust airflow holes of the atomizer in any direction you want.

You need a hex key to unfasten the screw.

Press few times the Fire button to turn the chip on.

2. Maintenance

The body of the Minion box mod is made of non-corrosive aluminium alloy. Doesn’t need special

treatment, however avoid contact whit aggressive liquids like: corrosive house hold cleaners

(anticalc) , long exposure with acids ( juice from citrus type or pineapple fruit).

To clean use humid and dry cloth.

The 510 connection contact pin and negative contact screw are made of brass so they can

corrode after time. For cleaning just use metal cleaner.

3. Charging

For fast charging you will need micro USB cable and USB charger whit 5.5V 1Amp output.

Thank you purchasing our product. If you have any question or you need technical

help, or for resolving problems, please contact us on: tek-divi[email protected]

2. NEGATIVE BATTERY CONTACT SCREW (unfasten the screw till you will be able

to pull the top cap)

3. ATOMIZER 510 CONECTION

4. FIRE BUTTON

5. HEX SCREW FOR 510 CONECTION ROTATING ADJUSTMENT

6. DOWN BUTTON

1. microUSB CHARGING PORT

2. DNA40 DISPLAY

3. WARRANTY SEALING

4. CHARGING INDICATORS: RED charging in progress

BLUE charging completed

Chip specifications / Evolv Dna 40

Temperature Protection

The Dna 40 is the first power supply for electronic cigarettes to directly measure

and limit the temperature of the heating coil during operation. By preventing the

coil from becoming too hot regardless of fluid, wicking or airflow, a variety of

undesirable situations can be prevented. For example, appropriate temperature

settings will prevent the wicking material from charring, which compromise taste

and introduces unintended chemicals into the vapor. Appropriate temperature

settings will also reduce the breakdown of flavoring and base liquid components,

which could impact taste or safety.

Evolv’s Temperature Protection Technology requires a heating coil made from

Nickel 200 alloy, rather than Nickel Chromium or Kanthal alloys. Nickel 200 is

commercially pure nickel. It is often sold in vapor shops and online as

”non-resistance wire”. If the temperature reaches the maximum value, the wattage

applied to the atomizer coil is reduced to prevent overheating. Please note that the

temperature reading is the average temperature of the atomizer coil, and care

should taken to construct the heating coil so that the temperature is uniform,

without hot or cold spots. Ensure that the coil does not short to itself.

Minimum

Typical

Maximum

Output Power

1 Watt

40 Watt

Output Voltage

1 Volt

9.0 Volts

Output Current, continous

16.0 Amps

Output Current, instantaneous peak

23.0 Amps

Atomizer Resistance, standard wire

0.16 Ohm

0.7 Ohm

2.0 Ohms

Atomizer Resistance, temp. sensing wire

0.10 Ohm

0.4 Ohm

1.0 Ohm

Input Voltage

3.1 Volts

3.7 Volts

4.3Volts

Temperature limit

200°F

450°F

600°F

Input Current

0.5 Amps

8.0 Amps

16.0 Amps

Efficiency

92%

Charging USB current 5.5V

1 Amp

Because wattage, not temperature controls vapor volume, large vapor volumes

can be produced without unnecessarily high temperatures. Temperature Protection

is most helpful if the atomizer begins to dry out, the user pauses during a puff, the

beginning or end of the puff, or if the wattage setting is inappropriate for the

attached atomizer.

In normal operation, when the device is not firing the maximum temperature

setting is displayed on the screen. When device is firing, the actual average

temperature of the coil is displayed on the screen.

By default, the Temperature Protection setting is 450°F. To change the limit

1. Lock the device by pressing the Fire button five times.

2. Hold down the Up and Down adjust buttons for two seconds.

3. After two seconds, the maximum temperature will be displayed, and the

UP and Down buttons should be released.

4. Use the UP and Down buttons to adjust the maximum temperature

5. When the display shows the desired maximum temperature, press the Fire

button to exit temperature adjust mode.

The maximum temperature is adjustable between 200°F and 600°F. To disable

the temperature protection entirely, adjust the limit up to 600°F, then press the

UP button on additional time. The temperature limit will read OFF. This will also

disable the prompt when a new atomizer is attached.

Preheat

When the Dna 40 is used with a temperature sensing atomizer, an additional

feature called Preheat is activated. No vapor is produced when the temperature

is below the boiling point of the liquid. Preheat applies extra power until the

heating coil is up to operating temperature to shorten the delay between

pressing the fire button and generating vapor. Because the preheat is

temperature based, it will not overheat or burn the vapor.

Attaching a New Atomizer

The Dna 40 uses the resistance of the atomizer to calculate the temperature of

the heating coil.

It continually looks to see whether a new or changed atomizer has been

connected. If you are using temperature protection, be careful to only attach new

atomizers that have cooled to room temperature to the device. If a new atomizer

is attached to the Dna 40 before it has cooled down, the temperature may read

and protect incorrectly until the new atomizer cools.

When you connect a new atomizer or disconnect a reconnect your existing

atomizer, the Dna 40 will prompt you to confirm this change. When you fire the

first time, before activating the Dna 40 will prompt “ New Coil? UP YES/DOWN

NO”. When you see this prompt, if you have attached a new atomizer, press the

UP button. If you have disconnected and reconnected the same atomizer, press

the DOWN button.

Operation

Basic operation of the Dna 40 is as follows. To wake the device from power off

state, tap the Fire button. To generate vapor, press the Fire button. To change

the wattage setting for more or less vapor, click or hold the UP and DOWN

buttons.

Display

The normal and special operating modes shown on display are discussed

below. The Dna 40 will automatically detect whether a temperature sensing

(Nickel 200) or standard Kanthal etc) coil is attached.

Temperature Protected

Watt setting: The power level currently set on the Dna 40

Battery indicator: The current state of charge of the battery.

Temperature display: When not firing, the maximum heating coil temperature

setting. While firing, the actual temperature of the heating coil is displayed.

Ohms display: The resistance of atomizer attached to the device. This is measured

only when the unit is supplying power to the atomizer. At other times, it shows

the most recent measurement.

Non-temperature Protected

Watt setting: The power level currently set on the Dna 40.

Battery indicator: The current state of charge of the battery.

Volts display: The output voltage being supplied to the atomizer.

Ohms display: The resistance of atomizer attached to the device. This is

measured only when the unit is supplying power to the atomizer. At other times,

it shows the most recent measurement.

Modes

Locked mode: Pressing the Fire button five times with less then0.7 seconds

between presses will cause the device to enter Locked mode. In locked mode, the

device will not fire and the output power will not adjust accidentally. While in

Locked mode, the screen will be off, except that pressing a button will show

“Locked, Click 5x”. To exit locked mode, press the fire button 5 times.

Stealth mode: While locked, holding the Fire and DOWN buttons simultaneously

for 5 seconds will switch to stealth mode. In this mode the display is off. It will still

exit power locked mode the Fire and DOWN buttons simultaneously for 5

seconds. This setting is stored to internal flash memory, and remains if power is

removed.

Right mode and Left mode: While locked, holding the Fire and UP buttons

simultaneously for 5 seconds flips the display. This allows for accommodating to

left or right handed use. This setting is stored to internal flash memory, and

remains if power is removed.

Power Locked mode: Holding down both the UP and DOWN buttons for 2 seconds

will place the device in Power Locked mode. In this mode, the mod will operate

normally, but you will not be able to change to power setting. This mode prevents

accidental power level change due to the buttons being pressed while in a pocket.

To exit Power Locked mode, hold UP and DOWN buttons for 2 seconds.

Maximum Temperature Adjust: From Locked mode, holding down both the UP

and DOWN buttons for 2 seconds will place the device in Max Temperature

Adjust mode. Once this mode is entered, the max temperature will be displayed.

The UP and DOWN buttons are used to adjust the max temperature. To save the

new temperature setting and exit, press the Fire button.

Error Messages:

The Dna 40 will indicate a variety of error states.

Check Atomizer: The Dna 40 does not detect an atomizer, the atomizer has

shorted out, or the atomizer resistance is incorrect for the power setting.

Shorted: The atomizer or wiring are shorted circuited.

Weak Battery: The battery needs to be charged, or a higher rate battery needs to

be used. If this happens, the Dna 40 will continue to fire the atomizer, but will not

be able to provide the desired wattage. The Weak Battery message will continue

to flash for few seconds after end of puff.

Temperature protection: The heating coil reached the maximum allowed

temperature during the puff. If this happens, the Dna 40 will continue to fire, but

will not be able to provide the desired wattage.

Ohms Too High: The resistance of the atomizer coil is too high for the current

wattage setting. If this happens, the Dna 40 will continue to fire, but will not be

able to provide the desired wattage. The Ohms Too High message will continue to

flash for a few seconds after the end of puff.

Ohms Too Low: The resistance of the atomizer coil is too low for the current

wattage setting. If this happens, the Dna 40 will continue to fire, but will not be

able to provide the desired wattage. The Ohms Too Low message will continue to

flash for a few seconds after the end of puff.

Too Hot: The Dna 40 has onboard temperature sensing. It will shut down and

display this message if the internal board temperature becomes excessive.

Auto power down:

The screen will be at full brightness while firing. After 10 seconds with no button

presses, the screen will dim. 30seconds after the last button press, the screen will

fade out and the device will go into sleep mode. To wake the device, press the

Fire button.

Table of contents

Other Tek Division Vaporizer manuals

Tek Division

Tek Division Minion User manual

Popular Vaporizer manuals by other brands

Vivant

Vivant Dabox Pro user manual

Pulsar

Pulsar Triad user manual

Smok

Smok MAG user guide

Puzhen

Puzhen Bamboo quick guide

XVAPE

XVAPE FOG PRO instruction manual

DaVinci

DaVinci MIQRO user manual

iQOS

iQOS lil SOLID 2.0 user guide

CHART

CHART VaporMan 125 product manual

InnoCigs

InnoCigs EGRIP 2 LIGHT user manual

OOZE

OOZE Movez instruction manual

STORZ & BICKEL

STORZ & BICKEL Volcano Hybrid Quick start manual

STEAMAX

STEAMAX STICK X8 user manual

Storz & Bickel GMBH

Storz & Bickel GMBH Crafty Instructions for use

Joyfect

Joyfect Freaky One user guide

SIGELEI

SIGELEI 213 FOG user manual

Eleaf

Eleaf Lemo 2 user manual

Vapor Brothers

Vapor Brothers VB Eleven Pen quick start guide

STORZ & BICKEL

STORZ & BICKEL VOLCANO CLASSIC Instructions for use