TeeJet Technologies 70 Series User manual
www.teejet.com
User GUide
Connections Table and Assembly
Contact Color Description Contact Color Description
1 9 Brown +12v Speed Sensor
2 Wht/Grn SPEED signal 10 Green GND for speed sensor
3 Green Boom Sense input (+12v = work) 11 Yellow ALARM 2 output
4 12
5 Gray ALARM 1 output
6
7
8
Note: Boom Sense +12v supply MUST share the same ground as the console.
Boom Sense - GREEN
Alarm 2 - YELLOW
Alarm 1 - GRAY
SPEED
P
ro
CLR
70 Series
001-US
V1.11
Power Cable
45-05268
To Battery
71 Speed Area Monitor
75-30010
Main Harness
45-05429
Proximity
Sensor
16-40004
Pos Color Function
A Brown (+V)
B Wht/Grn Signal
C Green Ground
Speed
3 pos. Deutsch Skt.
Pos Color Function
A Red (+12V)
B Black Ground
Power Supply
Functionality
Function Key Description
1. Power on Pro The unit will power on and show the Info screen.
Software name and Version are displayed. 001-US
V1.12
2. Power off and The unit will power off
3. Selection of working
screen or
The rst line on display shows Speed (MPH)
Second line is user selectable (Distance, Area, or Total Area)
Example:000
Shows Upper line Speed (MPH / KPH) and Lower line
Distance (FT / M)
US Units
7.5MPH
105.7FT
Metric Units
12.0KPH
32.2M
4. Master On Pro
The Pro key will act as the master switch and when pressed the console will begin to accumulate
area and distance.
NOTES: The master switch must be off to enter into setup
An external switch can be connected to the green boom sense wire to signal to the console
to start accumulating.
70 series
speed AreA Monitor
98-05072 R3 EN-US English
© TeeJet Technologies 2013
TeeJet Technologies
1801 Business Park Drive
Springeld, Illinois 62703 USA
www.teejet.com
User GUide
Program
Function Display Possible Actions Comments
Access or Exit Push Pro for 3 seconds Master must be off
Width Setup width
setup Pro to access Width setup
to modify the width value
Master must be off
Speed Setup speed
setup
Pro to access Speed setup
Manual Calibration
to modify speed sensor calibration number
Auto Calibration
CLR to access auto calibration
Mark off a known distance of 300ft / 100m
Pro to Start auto calibration
Drive the 300ft / 100m course
Pro to End auto calibration
Pro to Save calibration number
Master must be off
When using the Auto calibration procedure it
is best to mark a course on a surface that best
matches real-time operations. For the best
results repeat the Auto calibration procedure
3 times and take an average. Each run should
produce a similar calibration number.
Alarms
Function Display Possible Actions Comments
Alarm 1
Speed Distance Area Alarm
1
Pro to access Alarm 1
to select alarm options (None, Distance, Speed,
or Area)
Pro to access Distance, Speed, or Area
to adjust alarm value of Distance, Speed, or
Area.
CLR to clear alarm message during operation.
CLR for 3 seconds to clear alarm value and
reset Alarm.
NO audible alarm.
Alarm 1 output (gray wire) is +12v when Alarm 1
is active.
During real-time operation the alarm value must
be exceeded for at least 3 consecutive seconds
to activate alarm.
Displayed Speed, Distance, or Area must be
cleared or reduced below Alarm value to reset
alarm.
Alarm 2
Speed Distance Area Alarm
2
Pro to access Alarm 2
to select alarm options (None, Distance, Speed,
or Area)
Pro to access Distance, Speed, or Area.
to adjust alarm value of Distance, Speed, or
Area.
CLR to clear alarm message during operation.
CLR for 3 seconds to clear alarm value and
reset Alarm.
Audible alarm.
Alarm 2 output (yellow wire) is +12v when
alarm 2 is active.
During real-time operation the alarm value
must be exceeded for at least 3 consecutive
seconds to activate alarm.
Displayed Speed, Distance, or Area must
be cleared or reduced below Alarm value to
disable alarm.
Other TeeJet Technologies Monitor manuals
