TECPEL OS-81B User manual
TECPEL CO.，LTD.
OS-81B
Chapter Title Page
6
6
7
8
8
10
11
11
12
13
15
15
15
17
19
19
20
20
22
27
29
31
33
1
Table of Contents
1 Before You Start
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
2 Using The Testing Tool
Reading the screen
The Meter Structure
Functional Buttons
3 Making Measurements
A. Scope Mode
i. Setting up the Sleep Mode, Contrast, Beep
ii. ACV, DCV, Hz, ACV and DCA Range
iii. Trigger function
iv. Waveform data save and recall
B. Digital Multimeter Mode
i. Measuring Voltages
ii. Measuring Currents
iii. Measuring Resistance
iv. Testing Diodes
v. Testing for Continuity
vi. Measuring Frequency / Duty Cycle
2
35
37
38
38
39
40
41
41
42
43
43
44
44
45
45
46
46
47
48
49
49
50
Chapter Title Page
Table of Contents
A.
B.
C.
D.
E.
F.
G.
DC Voltage
AC Voltage
DC Current
AC Current
Resistance
Diode Test
Continuity Test
vii. Measuring Capacitance
4 Using Software
5 Maintenance The Test Tool
A. General Service
B. Replacing the Fuses
C. Replacing the Battery
6 Specifications
Safety and Compliances
Physical Specifications
General Specifications (Digital Multimeter)
General Specifications (Scope)
Feature Summary
Basic Specifications (Digital Multimeter)
Basic Specifications (Scope)
Detailed Accuracy Specifications
OS-81B Oscilloscope multimeter
3
50
51
Chapter Title Page
Table of Contents
H. Frequency and Duty Cycle %
I. Capacitance
4
7
10
11
13
Table Title Page
List of Tables
1-1 Unpacking Inspection
1-2 International Electrical Symbols
2-1 Reading the Screen
2-2 Functional Buttons
OS-81B Oscilloscope multimeter
5
12
13
17
21
23
24
25
27
29
31
33
35
39
40
Figure Title Page
List of Tables
2-1 Meter Structure
2-2 Functional Buttons
3-1 Waveform Display
3-2 Voltages Measurement
3-3 µA Range Measurement
3-4 mA Range Measurement
3-5 10A Range Measurement
3-6 Resistance Measurement
3-7 Diode Test
3-8 Continuity Test
3-9 Frequency / Duty Cycle Measurement
3-10 Capacitance Measurement
5-1 Fuse Replacement
5-2 Battery Replacement
6
Overview
This Operating Manual covers information on safety
and cautions. Please read the relevant information
carefully and observe all the Warningsand Notes
strictly.
Warning
To avoid electric shock or personal injury, read the
“Safety Information” and “Rules for Safe Operation”
carefully before using the Meter.
Scope Digital Multimeter OS-81B (hereafter referred
to as “the Meter”) is a 3999 counts and 3 3/4 digits
adopting digital control techique with both waveform
and multimeter all in one.
Scope mode is a complete intelligent measurement
system including signal input, sampling, data process,
auto search and waveform save and recall. It has
Chapter 1
Before You Start
bandwidth TECPEL OS-81B : 8MHz, real-time sample
rate 40MS/s with peak rate sampling process can catch
up pulse industrial signal.It can measure AC/DC engine,
transducer, circuit, control, UPS and industrial
equipments. It is an ideal tools in professional repairing
industries.
Digital Multimeter mode can measure AC voltage and
current, DC voltage and current, Resistance,
Capacitance, Frequency, Duty Cycle, Diodes and
Continuity.
OS-81B Oscilloscope multimeter
7
Item Description Qty
Unpacking Inspection
Open the package case and take out the Meter. Check the items shown on Table 1-1 carefully to see any missing
or damaged part:
In the event you find any missing or damage, please contact your dealer immediately.
1
2
3
4
5
6
7
8
9
10
English Operating Manual
USB interface cable
CD-ROM (Installation Guide & Computer Interface Software)
Test Lead
Alligator Clip
Power Adaptor
1.5V Batteries (R6)
Carrying bag
Scope Probe (available at extra cost)
BNC probe (available at extra cost)
1 piece
1 piece
1 piece
1 pair
1 piece
1 piece
4 pieces
1 piece
1 piece
Table 1-1. Unpacking Inspection
8
Safety Information
This Meter complies with the standards IEC61010 safety
measurement requirement: in pollution degree 2,
overvoltage category (CAT. II 1000V, CAT.III 600V) and
double insulation.
CAT.II: Local level, appliance, PORTABLE EQUIPMENT
etc., with smaller transient overvoltages than CAT. III
CAT. III: Distribution level, fixed installation, with smaller
transient overvoltage than CAT. IV
Use the Meter only as specified in this operating manual,
otherwise the protection provided by the Meter may be
impaired.
In this manual, a Warningidentifies conditions and
actions that may pose hazards to the user, or may
damage the Meter or the equipment under test.
A Note identifies the information that user should pay
attention to.
Warning
International electrical symbols used on the Meter and
in this Operating Manual are explained on page 10.
Rules For Safe Operation
To avoid possible electric shock or personal injury,
and to avoid possible damage to the Meter or to the
equipment under test, adhere to the following rules:
Before using the Meter inspect the case. Do not
use the Meter if it is damaged or the case (or
part of the case) is removed. Look for cracks
or missing plastic. Pay attention to the insulation
around the connectors.
Inspect the test leads for damaged insulation or
exposed metal. Check the test leads for
continuity. Replace damaged test leads with
identical model number or electrical
specifications before using the Meter.
Do not apply more than the 1000V rms between
any terminal and grounding to avoid electric
OS-81B Oscilloscope multimeter
9
shock or damages to the Meter.
The rotary switch should be placed in the right
position and no any changeover of range shall
be made during measurement is conducted to
prevent damage of the Meter.
When the Meter working at an effective voltage
over 60V in DC or 42V rms in AC, special care
should be taken for there is danger of electric
shock.
Use the proper terminals, function, and range
for your measurements.
Do not use or store the Meter in an environment
of high temperature, humidity, explosive,
inflammable and strong magnetic field. The
performance of the Meter may deteriorate after
dampened.
When using the test leads, keep your fingers
behind the finger guards.
Disconnect circuit power and discharge all high-
voltage capacitors before testing resistance,
continuity, diodes.
Before measuring current, check the Meter’s
fuses and turn off power to the circuit before
connecting the Meter to the circuit.
Replace the battery as soon as the battery
indicator appears. With a low battery, the
Meter might produce false readings that can lead
to electric shock and personal injury.
When servicing the Meter, use only the same
model number or identical electrical
specifications replacement parts.
The internal circuit of the Meter shall not be
altered at will to avoid damage of the Meter and
any accident.
Soft cloth and mild detergent should be used to
clean the surface of the Meter when servicing.
No abrasive and solvent should be used to
prevent the surface of the Meter from corrosion,
damage and accident.
The Meter is suitable for indoor use.
Turn the Meter off when it is not in us e and take
out the battery when not using for a long time.
Constantly check the battery as it may leak when
it has been using for some time, replace the
battery as soon as leaking appears. A leaking
battery will damage the Meter.
Table of contents
Other TECPEL Multimeter manuals
Popular Multimeter manuals by other brands
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 operating instructions
PeakTech
PeakTech 4000 Procedure of calibration
YOKOGAWA
YOKOGAWA 90050B user manual
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 operating instructions
Fluke
Fluke 8846A Programmer's manual
Tempo Communications
Tempo Communications MM200 instruction manual
