TECHLIGHTING 700KLMRT30E Series User manual
1.0
Installation Instructions for
Kable Lite Mini Surface Electronic Transformer
700KLMRT30E_
1
920KLMSET
GP I :ENERAL RODUCT NFORMATION
This product is ETL listed and suitable only for indoor dry
locations and approved for use at any height above the
finished floor.
A typical installation is shown. Specific installation must be
in accordance with local electrical codes.
This product may be dimmed only with a low voltage
electronic dimmer. Using a dimmer not designed for low
voltage electronic applications may work initially, but could
eventually cause transformer failure and will void the
warranty. The dimmer must be derated as indicated by the
dimmer manufacturer.
This product is intended for use with Tech Lighting low
voltage lighting systems only.
Read all instructions thoroughly. Read "Important Safety
Information" on page 3 before proceeding with the
installation.
STURFACE RANSFORMERS
Important Safety Information
Turn the electrical power off before modifying the lighting
system in any way.
The fixtures used with the system must be identified for
used with the corresponding system.
Minimum volume of the electrical box must be 6 cubic
inches (98 cubic centimeter).
Load the circuit of the remote transformers to no more than
the maximum rated capacity as specified.
To reset the electronic surface transformer, turn the power
off then on (main power, breaker panel, or wall switch).
1
To reduce the risk of fire and burns, do not install this
lighting system where the uninsulated open bus bar
conductors can be shorted or contact any conductive
materials.
When using a Power Extender, refer to the Power Extender
instructions before performing any installations for this
transformer.
To reduce the risk of the system overheating and possibly
causing a fire, make sure all the connections are tight.
Do not install fixture assemblies closer than six inches to
curtains or similarly combustible materials.
CAUTION - RISK OF FIRE
This product must be installed in accordance with
the applicable installation code by a person familiar
with the construction and operation of the product
and the hazards involved.
Use minimum 90°c supply conductors.
2
1A
Separate the mounting plate from the transformer by
removing the two screws.
#8-32 SCREW
1B
#8-32 SCREW
SCREWSCREW CANOPY
MOUNTING PLATE
Attach the mounting plate to the electrical box using
the two #8-32 screws provided.
1C
54
1D
Reattach the transformer to the mounting plate by
securing it with the two screws.
1
Install the Transformer
2
3
4
Connect the mounting plate ground wire to a suitable
ground in accordance with local electrical codes.
Connect the white transformer wire to the neutral
power line wire with a wire nut.
Connect the black transformer wire to the hot power
line wire with a wire nut.
Place all wires and wire nut connections inside the
electrical box.
5
3
7
6
Connect the Transformer Wires
Directly to Kable Lite Cables
INSULATED KABLE
LITE CABLE
½"
KNIFE
When using insulated Kable Lite cables, remove ½" of
the insulation from each cable (where the power feed
connector is going to be mounted) with a sharp knife.
Make sure not to cut or nick the cable.
KABLE LITE CABLE
POWER FEED
CONNECTOR
#10-32 SLOTTED
SET SCREW
POWER FEED WIRE
Unscrew the #10-32 slotted head set screw from the tip
of the power feed connectors with a screwdriver. Place
the power feed connectors one onto each Kable Lite
cable and tighten the #10-32 slotted set screw on the
tip with the screwdriver.
#6-32 SET SCREW
2A
2B
1
1
2
2
3
KABLE LITE CABLE
M4 SET SCREW
M4 SET SCREW
2 MM
ALLEN WRENCH
KABLE LITE CABLE
POWER
FEED WIRE
POWER FEED WIRE
2 MM ALLEN WRENCH
Remove the power feed connector by loosening the
#6-32 set screw with 1/16 Allen wrench (refer to 2B).
Feed the uninsulated portion of the power feed wire
(one for each turnbuckle) into the turnbuckle hole.
Tighten the M4 set screw with the 2MM Allen wrench.
Connect the Transformer Wires
to Universal Turnbuckles
Connect the Transformer Wires
to Slimline Turnbuckles
Remove the power feed connector by loosening the
#6-32 set screw with 1/16 Allen wrench (refer to 2B).
Feed the uninsulated portion of the power feed wire
(one for each turnbuckle) into the turnbuckle hole.
Tighten the M4 set screw with the 2MM Allen wrench.
3A 4A
1
2
3
2
3
1
2
3
2
3
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2014 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
SAVE THESE INSTRUCTIONS!
4
Other TECHLIGHTING Transformer manuals
