TDK-Lambda PHV Series User guide

IEEE DIGITAL INTERFACE SETUP MANUAL FOR

PHV Series High Voltage

POWER SUPPLY

Document: 83550130 Rev A

TDK-LAMBDA AMERICAS

405 Essex Road, Neptune, NJ 07753

Tel: (732) 922-9300

Fax: (732) 922-9334

Web: www.us.tdk-lambda.com/hp

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

Table of Contents

1. Overview...................................................................................................................................3

1.1. Scope........................................................................................................................................3

1.2. ADDR LED................................................................................................................................3

1.3. Service Request (SRQ) LED.....................................................................................................3

2. Interface setup information........................................................................................................5

2.1. GPIB primary address (PA).......................................................................................................5

2.2. Other DIP switch settings..........................................................................................................5

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

1. Overview

1.1. Scope

This manual applies to PHV series power supplies equipped with the IEEE digital interface

option. The manual describes setting the GPIB interface address only.

The IEEE interface programming commands can be found in the Digital Interface

Command Reference manual (document 83550100) downloadable from the PHV product

page: http://www.us.tdk-lambda.com/hp/product_html/PHVpower.htm.

The IEEE interface is located on the rear panel of the power supply. A sketch is shown

below.

IEEE Interface features

1- IEEE-488 interface connector

2- Configuration DIP switch (see section 2.1)

3- Interface Addressed LED (see section 1.2)

4- Service Request LED (see section 1.3

1.2. ADDR LED

This LED illuminates when the interface is either in listener addressed state or talker

addressed state.

1.3. Service Request (SRQ) LED

This LED illuminates when the interface asserts the SRQ line. After a serial poll the LED

extinguishes.

83550130 Revision A

THIS PAGE LEFT INTENTIONALLY BLANK

83550130 Revision A

2. Interface setup information

For normal operation, only the GPIB primary address should be adjusted using switches 1

through 5 if required. The other switches, 6 through 8 remain in the OFF position.

2.1. GPIB primary address (PA)

The GPIB primaryaddress (PA) enables identification of all units connected to an IEEE-488

bus system, and each unit connected to the bus must be assigned a unique PA.

The Host PC usually has PA=0 and the connected units usually have addresses from 4

upwards. Normally PHV power supplies arefactory configured with the PA set to 8.

The user can change the factory set PA via a DIP switch located on the IEEE-488 interface

converter on the rear panel of the unit (see the figure on page 3). It is not necessary to

open the power supply.

After changing a configuration switch, the power supply should be turned off for 5 seconds

and turned on again.

To change the GPIB PA, the user should only change switches 1 through 5. The unit is

factory set with switch 4 in the ON position and switches 1, 2, 3, and 5 are in the OFF

position (PA=8).

The switch settings follow the binary system:

Switch 1 has value 1

Switch 2 has value 2

Switch 3 has value 4

Switch 4 has value 8

Switch 5 has value 16

Example: To set the GPIB PA to 9, Switches 1 and 4 are ON, switches 2, 3, and 5 are

OFF. To set the GPIB PA to 20, Switches 3 and 5 are ON, switches 1, 2, and 4 are OFF.

2.2. Other DIP switch settings

DIP switches 6, 7, and 8 are special functions and are factory set to the OFF position and

the settings should not be changed. Contact the factory for further information.

Other manuals for PHV Series

Table of contents

Other TDK-Lambda Power Supply manuals

TDK-Lambda

TDK-Lambda 500A User manual

TDK-Lambda

TDK-Lambda Genesys Series User manual

TDK-Lambda

TDK-Lambda FPS1000 Series User manual

TDK-Lambda

TDK-Lambda HWS 1800T Series User manual

TDK-Lambda

TDK-Lambda EZA2500 Series Installation guide

TDK-Lambda

TDK-Lambda Genesys GEN8-300 User manual

TDK-Lambda

TDK-Lambda Genesys Series User manual

TDK-Lambda

TDK-Lambda HFE2500 Series User manual

TDK-Lambda

TDK-Lambda GENESYS GEN 5kW Series User manual

TDK-Lambda

TDK-Lambda Alpha 1000 User manual

TDK-Lambda

TDK-Lambda HWS-L/BAT Series User manual

TDK-Lambda

TDK-Lambda Genesys User manual

TDK-Lambda

TDK-Lambda LZS-A1000-2 User manual

TDK-Lambda

TDK-Lambda TPF45000-385 User manual

TDK-Lambda

TDK-Lambda PFE300SA Series User manual

TDK-Lambda

TDK-Lambda Z+ series User manual

TDK-Lambda

TDK-Lambda CPFE1000FI Series User manual

TDK-Lambda

TDK-Lambda DRB120 Series User manual

TDK-Lambda

TDK-Lambda HWS 1500 Series User manual

TDK-Lambda

TDK-Lambda GWS250 Series User manual

TDK-Lambda

TDK-Lambda QM Series Supplement

TDK-Lambda

TDK-Lambda GH10-150 Setup guide

TDK-Lambda

TDK-Lambda FPS-S1U User manual

TDK-Lambda

TDK-Lambda GH10-100 User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual