TDK-Lambada Z10-20 User manual

USER MANUAL

Series

This Manual Covers Models:

Z10-20 Z20-10 Z36-6 Z60-3.5 Z100-2

Z10-40 Z20-20 Z36-12 Z60-7 Z100-4

Z10-60 Z20-30 Z36-18 Z60-10 Z100-6

Z10-72 Z20-40 Z36-24 Z60-14 Z100-8

Programmable DC Power Supplies

200W/400W/600W/800W

Built-in USB, RS-232 & RS-485 Interface

IA710-04-01K

Concentration Values of Toxic and Hazardous Substances/Elements (wt%) Notes

Lead (Pb)

0.1wt%

Mercury (Hg)

0.1wt%

Cadmium (Cd)

0.1wt%

Hexavalent

Chromium

(Cr6+)

0.1wt%

Polybrominated

Biphenyls (PBB)

0.1wt%

Polybrominated Diphenyl

Ethers (PBDE)

0.1wt%

Case O O O O O O

Plastic panel O O O O O O

PCB's assembly X O O O O O

Inner metal parts O O O O O O

Inner cables O O O O O O

Accessories O O O O O O Provided in the package

O : Indicates that the concentration values of toxic and hazardous substances in all ”homogeneous materials” of respective parts and materials does not exceed the concentration limits

regulated by ”SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products”.

X : Indicates that the concentration value of a toxic or hazardous substance included in a ”homogeneous part” of a respective part or material exceeds the concentration limit regulated by

”SJ/T 11363-2006 Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products”.

Date of manufacture

Part Name Z+Series: Z200, Z400, Z600, Z800 POWER SUPPLY Product Weight Z200: 1.9Kg

Product Weight Z400: 1.9Kg

Product Weight Z600: 2.1Kg

Product Weight Z800: 2.1Kg

Information Concerning Inclusion of Toxic and Hazardous Substances

This information sheet was prepared based on People's Republic of China ”Management Methods for Controlling Pollution Caused by Electronic Information Products Regulation”and

”SJ/T 11364—2006 Marking for Control of Pollution Caused by Electronic Information Products”.

As People's Republic of China ”Management Methods for Controlling Pollution Caused by Electronic Information Products Regulation”is a different legislation from EU RoHS2 Directive

(2011/65/EU), inquiries concerning EU RoHS2 Directive (2011/65/EU) information should be done separately.

Table of Contents

WARRANTY............................................................................................................................................. 8

REGULATORY NOTICES....................................................................................................................... 9

SAFETY INSTRUCTIONS...................................................................................................................... 9

CHAPTER 1: GENERAL INFORMATION

1.1 User Manual Content .................................................................................................................. 13

1.2 Introduction ................................................................................................................................... 13

1.2.1 General Description ................................................................................................................................. 13

1.2.3 Features and Options ............................................................................................................................. 13

1.2.4 Multiple Output Power System ........................................................................................................ 14

1.2.5 Control via the USB or RS232/485 Communication Ports ................................................ 14

1.2.6 Analog Voltage Programming and Monitoring ..................................................................... 14

1.2.7 Parallel Operation ..................................................................................................................................... 14

1.2.8 Output Connections ............................................................................................................................... 14

1.2.9 Cooling and Mechanical Construction ........................................................................................ 14

1.3 Accessories ..................................................................................................................................... 15

1.3.1 General ............................................................................................................................................................. 15

1.3.2 Serial Link Cable ......................................................................................................................................... 15

1.3.3 Misc. Hardware ........................................................................................................................................... 15

1.3.4 AC Cables ........................................................................................................................................................ 15

1.3.5 Serial Port Cables........................................................................................................................................ 15

CHAPTER 2: SPECIFICATIONS

2.1 Z+200 Series Specifications....................................................................................................... 16

2.2 Z+400 Series Specifications ......................................................................................................20

2.3 Z+600 Series Specifications ...................................................................................................... 24

2.4 Z+800 Series Specifications.......................................................................................................28

2.5 Supplemental Characteristics.................................................................................................. 31

2.6 Z200W/400W/600W/800W Outline Drawing.....................................................................32

2.7 Z200W/400W/600W/800W Optional IEEE, Isolated Analog

Interface Outline Drawing .......................................................................................................33

2.8 Z200W/400W/600W/800W Front Panel Output Binding

Post/Socket Outline Drawing L/L2 .......................................................................................34

CHAPTER 3: INSTALLATION

3.1 General.............................................................................................................................................35

3.2 Preparation for Use......................................................................................................................35

3.3 Initial Inspection...........................................................................................................................35

3.4 Rack Mounting..............................................................................................................................35

3.5 Location, Mounting and Cooling ...........................................................................................36

3.6 AC Source Requirements...........................................................................................................36

3.7 AC Input Power Connection..................................................................................................... 36

3.7.1 AC Input Connector ..................................................................................................................................36

3.7.2 AC Input Cord ............................................................................................................................................... 37

3.8 Turn-On Checkout Procedure..................................................................................................37

3.8.1 General ............................................................................................................................................................. 37

3.8.2 Prior to Operation...................................................................................................................................... 37

3.8.3 Constant Voltage Check ........................................................................................................................ 38

3.8.4 Constant Current Check......................................................................................................................... 38

3.8.5 OVP Check...................................................................................................................................................... 38

3.8.6 UVL Check ...................................................................................................................................................... 38

3.8.7 Foldback Check........................................................................................................................................... 39

3.9 Connecting the Load.................................................................................................................. 39

3.9.1 Load Wiring.................................................................................................................................................... 39

3.9.2 Current Carrying Capacity ....................................................................................................................40

3.9.3 Wire Termination ........................................................................................................................................ 41

3.9.4 Noise and Impedance Effects............................................................................................................. 41

3.9.5 Inductive Loads........................................................................................................................................... 41

3.9.6 Making the Load Connections........................................................................................................... 41

3.9.7 Connecting Single Loads, Local Sensing (default)................................................................. 43

3.9.8 Connecting Single Loads, Remote Sensing............................................................................... 43

3.9.9 Connecting Multiple Loads, Radial Distribution Method.................................................. 44

3.9.10 Multiple Load Connection with Distribution Terminals...................................................44

3.9.11 Grounding Outputs ................................................................................................................................ 45

3.10 Local and Remote Sensing......................................................................................................45

3.10.1 Sense Wiring................................................................................................................................................ 45

3.10.2 Local Sensing..............................................................................................................................................46

3.10.3 Remote Sensing........................................................................................................................................46

3.10.4 J2 Sense Connector Technical Information ............................................................................. 47

3.11 Repackaging for Shipment ..................................................................................................... 47

CHAPTER 4: FRONT/REAR PANEL CONTROLS AND CONNECTORS

4.1 Introduction ...................................................................................................................................48

4.2 Front Panel Display and Controls..........................................................................................48

4.3 Rear Panel Connectors...............................................................................................................50

4.3.1 J1 Connector Terminal and Function............................................................................................. 52

4.3.2 J3 Connector Terminal and Function ............................................................................................ 53

4.4 Front Panel Display Messages .................................................................................................54

4.5 Navigating the Main Menu...................................................................................................... 55

4.5.1 Introduction................................................................................................................................................... 55

4.5.2 Exiting the Main Menu ........................................................................................................................... 56

4.6 Navigating Communication Menu ........................................................................................56

4.6.1 Introduction................................................................................................................................................... 56

4.6.2 Exiting the Communication Menu ................................................................................................. 57

4.7 Navigating the Protection Menu............................................................................................57

4.7.1 Introduction .................................................................................................................................................. 57

4.7.2 Exiting the Protection Menu ............................................................................................................... 57

CHAPTER 5: LOCAL OPERATION

5.1 Introduction ...................................................................................................................................58

5.2 Standard Operation.....................................................................................................................58

5.2.1 Constant Voltage Mode and Voltage Setting........................................................................... 58

5.2.2 Constant Current Mode and Current Setting........................................................................... 58

5.2.3 Automatic Crossover................................................................................................................................ 59

5.2.4 Output On/Off Control........................................................................................................................... 59

5.2.5 Safe Start and Auto-Restart Modes................................................................................................. 59

5.2.6 Viewing Software Revision................................................................................................................... 59

5.3 Alarms and Protective Functions ...........................................................................................60

5.3.1 Introduction................................................................................................................................................... 60

5.3.2 Over Voltage Protection ........................................................................................................................ 60

5.3.2.1 Setting the OVP Level ..........................................................................................................................60

5.3.2.2 Resetting the OVP Circuit.................................................................................................................. 61

5.3.3 Under Voltage Protection and Under Voltage Limit ........................................................... 61

5.3.3.1 Setting the UVP/UVL Mode and Level....................................................................................... 61

5.3.3.2 Activated UVP Alarm............................................................................................................................ 61

5.3.4 Foldback Protection ................................................................................................................................ 61

5.3.4.1 Setting the Foldback Protection.................................................................................................. 62

5.3.4.2 Activated FOLD Alarm......................................................................................................................... 62

5.3.5 Protection Delay......................................................................................................................................... 62

5.3.5.1 Setting the Protection Delay ........................................................................................................... 62

5.3.6 Over Temperature Protection............................................................................................................. 62

5.3.7 AC Fail Alarm................................................................................................................................................. 62

5.4 Series Operation...........................................................................................................................63

5.4.1 Series Connection for Increased Output Voltage................................................................... 63

5.4.2 Series Connection for Positive and Negative Output Voltage.......................................64

5.4.3 Remote Programming in Series Operation................................................................................64

5.5 Parallel Operation........................................................................................................................65

5.5.1 Introduction................................................................................................................................................... 65

5.5.2 Basic Parallel Operation.......................................................................................................................... 65

5.5.2.1 Master Unit Set Up................................................................................................................................. 65

5.5.2.2 Slave Unit Set Up ....................................................................................................................................66

5.5.2.3 Setting Over Voltage Protection................................................................................................... 66

5.5.2.4 Setting Foldback Protection............................................................................................................66

5.5.2.5 Connection to Load..............................................................................................................................66

5.5.3 Advanced Parallel Operation..............................................................................................................68

5.5.3.1 Master Unit Set Up................................................................................................................................. 68

5.5.3.2 Slave Unit Set Up ....................................................................................................................................68

5.6 Daisy-Chain Connection............................................................................................................69

5.7 Rear Panel (J3 Connector) Functions and Settings ..........................................................69

5.7.1 External Shut Off Function.................................................................................................................... 70

5.7.2 Interlock Function - Analog On/Off. (Enable/Disable)......................................................... 70

5.7.3 Auxiliary Programmed Function Pin 1 and Pin 2 .................................................................... 71

5.7.4 Power Supply OK Signal ......................................................................................................................... 72

5.8 Rear Panel (J1 Connector) Functions.....................................................................................72

5.8.1 CV/CC Signal.................................................................................................................................................. 72

5.9 Parameter Setting Memory......................................................................................................73

5.9.1 Default Setting ............................................................................................................................................. 73

5.9.2 Reset................................................................................................................................................................... 73

5.9.3 Last Setting Memory................................................................................................................................ 73

5.9.4 Save <1..4>...................................................................................................................................................... 74

5.9.5 Recall <1..4> ................................................................................................................................................... 74

CHAPTER 6: REMOTE ANALOG PROGRAMMING

6.1 Introduction ................................................................................................................................... 76

6.2 Local/Remote Analog Control................................................................................................. 76

6.3 Local/Remote Analog Indication............................................................................................76

6.4 Remote Voltage Programming of Output Voltage and Current.................................77

6.5 Remote Resistor Programming of Output Voltage and Output Current................. 78

6.6 Programming Monitoring of Output Voltage (V_MON) and Current (I_MON) ....79

CHAPTER 7: Serial RS232/RS485 and USB Interface

7.1 Introduction....................................................................................................................................80

7.2 Configuration.................................................................................................................................80

7.2.1 Default Setting .............................................................................................................................................80

7.2.2 Address Setting ...........................................................................................................................................80

7.2.3 Communication Interface Selection ............................................................................................. 80

7.2.4 Baud Rate Setting....................................................................................................................................... 81

7.2.5 Language Selection (RS232/RS485, USB)..................................................................................... 81

7.2.6 Setting Unit in Remote, Local Lockout or Local Mode........................................................ 81

7.3 Rear Panel RS232/485 Connector ...........................................................................................82

7.4 Connectig Power Supply To RS232 Or RS485 BUS............................................................ 83

7.5 Rear Panel USB Connector ........................................................................................................84

7.5.1 USB Getting Started...................................................................................................................................84

7.6 Multi Power Supply Connection to RS232 Or RS485 or USB.........................................84

7.7 GEN Protocol (GEN series communication language)..................................................... 85

7.7.1 Dat a Fo rmat .................................................................................................................................................... 85

7.7.2 End of Message............................................................................................................................................ 85

7.7.3 Command Repeat....................................................................................................................................... 85

7.7. 4 C he ck s um ........................................................................................................................................................ 85

7.7.5 Acknowledge ................................................................................................................................................ 85

7.7. 6 Ba ck s pa ce ........................................................................................................................................................ 85

7.7.7 Error Messages.............................................................................................................................................. 85

7.8 GEN Command Set Description ..............................................................................................86

7.8.1 General guides .............................................................................................................................................86

7.8.2 Command Set Categories..................................................................................................................... 86

7.8.3 Identification Commands...................................................................................................................... 86

7.8.4 Initialization Commands....................................................................................................................... 87

7.8.5 Output Commands................................................................................................................................... 87

7.8.6 Global Output Commands................................................................................................................... 89

7.8.7 Auxiliary Commands ................................................................................................................................ 91

7.8.8 Status Commands...................................................................................................................................... 91

7.9 Serial Communication Test Set-Up......................................................................................... 92

7.10 SCPI Protocol ................................................................................................................................92

7.10.1 Data Format.................................................................................................................................................. 92

7.10.2 End of Message ......................................................................................................................................... 92

7.10.3 End of Command .................................................................................................................................... 92

7.10.4 Checksum ..................................................................................................................................................... 93

7.10.5 SCPI Requirements .................................................................................................................................. 93

7.10.6 SCPI Command Hierarchy................................................................................................................... 93

7.10.7 Header............................................................................................................................................................. 93

7.10.8 Data Formats............................................................................................................................................... 94

7.10.9 Character Data............................................................................................................................................94

7.10.10 Commands Notes .................................................................................................................................. 94

7.11 SCPI Common Commands.......................................................................................................94

7.12 SCPI Subsystem Commands ...................................................................................................99

7.12.1 Output Subsystem................................................................................................................................... 99

7.12.2 Instrument Subsystem.........................................................................................................................102

7.12.3 Voltage Subsystem.................................................................................................................................102

7.12.4 Current Subsystem .................................................................................................................................104

7.12.5 Measure Subsystem...............................................................................................................................105

7.12.6 DISPlay Subsystem..................................................................................................................................106

7.12.7 INITiate Subsystem..................................................................................................................................107

7.12.8 LIST Subsystem.........................................................................................................................................107

7.12.9 STATus Subsystem ...................................................................................................................................109

7.12.10 SYSTem Subsystem .............................................................................................................................. 111

7.12.11 TRIGger Subsystem............................................................................................................................... 112

7.12.12 WAVE Subsystem ................................................................................................................................... 113

7.12.13 Global Subsystem.................................................................................................................................. 114

7.13 Command Summary................................................................................................................. 115

CHAPTER 8: ADVANCED FUNCTIONS

8.1 Introduction .................................................................................................................................. 119

8.2 FIX Mode ........................................................................................................................................ 119

8.3 LIST Mode ......................................................................................................................................120

8.4 WAVE Mode...................................................................................................................................121

8.5 Trigger.............................................................................................................................................122

8.5.1 Input Trigger.................................................................................................................................................122

8.5.2 Output Trigger............................................................................................................................................123

8.6 Transient Waveform Example.................................................................................................123

8.6.1 Wave Programing......................................................................................................................................123

8.6.2 Wave Execution via Communication PC....................................................................................123

8.6.3 Wave Execution via Front Panel ......................................................................................................124

8.7 Additional Examples..................................................................................................................124

8.7.1 List Example .................................................................................................................................................. 124

8.7.2 Waveform Example..................................................................................................................................124

CHAPTER 9: STATUS, FAULT AND SRQ REGISTERS

9.1 General............................................................................................................................................125

9.2 Power Supply Status Structure...............................................................................................126

9.3 Condition Registers....................................................................................................................126

9.3.1 Fault Register ...............................................................................................................................................126

9.3.2 Status Register............................................................................................................................................. 127

9.4 Conditional, Enable and Event Registers............................................................................127

9.4.1 Conditional Registers. .............................................................................................................................127

9.4.2 Event Registers............................................................................................................................................127

9.4.3 Enable Register...........................................................................................................................................127

9.5 Service Request ..........................................................................................................................127

9.6 Standard Event Status Group..................................................................................................128

9.6.1 Register Functions ....................................................................................................................................128

9.6.2 Register Commands................................................................................................................................128

9.6.3 Status Byte Register.................................................................................................................................129

9.6.4 Determining the Cause of a Service Interrupt.........................................................................129

9.6.5 Output Queue.............................................................................................................................................130

9.6.6 Error Messages............................................................................................................................................130

CHAPTER 10: ISOLATED ANALOG PROGRAMMING OPTION

10.1 Introduction ................................................................................................................................132

10.2 Specifications.............................................................................................................................132

10.2.1 0-5V/0-10V Option (PN: IS510)..........................................................................................................132

10.2.2 4-20mA Option (PN: IS420) ............................................................................................................... 132

10.3 Isolated Programming & Monitoring Connector..........................................................133

10.4 Setup and Operating Instructions ......................................................................................134

10.4.1 Setting Up Power Supply for 0-5/0-10V Isolated Programming and Monitoring134

10.4.2 Setting Up Power Supply for 4-20mA Isolated Programming and Monitoring134

CHAPTER 11: MAINTENANCE

11.1 Introduction.................................................................................................................................135

11.2 Units Under Warranty..............................................................................................................135

11.3 Periodic Maintenance..............................................................................................................135

11.4 Adjustments and Calibration................................................................................................135

11.5 Parts Replacement and Repairs ...........................................................................................135

11.6 Troubleshooting ........................................................................................................................135

11.7 Fuse Rating ..................................................................................................................................136

USER MANUAL INDEX ......................................................................................................................139

WARRANTY

ThisTDK-Lambda product is warranted against defects in materials and workmanship for a period

of five years from date of shipment. During the warranty period, TDK-Lambda will, at it’s option,

either repair or replace products which prove to be defective.

Limitation of Warranty

The warranty shall not apply to defects resulting from improper or inadequate usage or maintenance

by the buyer, buyer supplied products or interfacing.The warranty shall not apply to defects resulting

from unauthorized modifications or from operation exceeding the environmental specifications

of the product or if the QA seal has been removed or altered by anyone other than TDK-Lambda

authorised personnel. TDK-Lambda does not warrant the buyers circuitry or malfunctions of

TDK-Lambda products resulting from the buyer’s circuitry. Furthermore, TDK-Lambda does not

warrant any damage occurring as a result of the buyer’s circuitry or the buyer’s supplied products.

No other warranty is expressed or implied.

Warranty Service

This product must be returned to an authorized TDK-Lambda service facility for repairs or other

warranty service. For products returned toTDK-Lambda for warranty service, the buyer shall prepay

shipping charges to TDK-Lambda and TDK-Lambda shall pay the shipping charges to return the

product to the buyer. Refer to section 3.11 for Repackaging for Shipment.

Disclaimer

The information contained in this document is subject to change without notice. TDK-Lambda

shall not be liable for errors contained in this document or for incidental or consequential damages

in connection with the furnishing, performance or use of this material. No part of this document

may be photocopied, reproduced or translated into another language without the prior written

consent of TDK-Lambda.

Trademark Information

Microsoft™ and Windows™ are trademarks of Microsoft Corporation.

REGULATORY NOTICES

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case

the user will be required to correct the interference at his own expense.

WARNING:

Modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment under FCC Rules.

Safety Approvals

UL 61010-1 and CSA22.2 No.61010-1 - UL Recognized, C-UL for Canada.

IEC 61010-1 - CB Report and Certificate.

EN 61010-1 - CE mark.

EN 61326-1

Marking by the CE Symbol indicates compliance to the LVD and EMC Directives of the European Union.

A“Declaration of Conformity”in accordance with the preceding directives and standards has been

made and is on file at our EU representative TDK LAMBDA UK, located at Kingsley Avenue,

Ilfracombe, Devon EX34 8ES, UK.

A“Declaration of Conformity”may be accessed via company web site:

www.uk.tdk-lambda.com/technical-data/

WARNING:

This is a Class A product. On a domestic environment, this product may cause radio interference in

which case user may be required to take adequate measures.

OTHER

Z200, Z400, Z600, Z800 series are comply with the following Directives:

•RoHS2 Directive (2011/65/EU);

•WEEE Directive (2002/96/EC).

SAFETY INSTRUCTIONS

CAUTION:

The following safety precaution must be observed during all phases of operation, service and repair

of this equipment. Failure to comply with the safety precautions or warnings in this document violates

safety standards of design, manufacture and intended use of this equipment and may impair the built-in

protections within.TDK-Lambda shall not be liable for user’s failure to comply with these requirements.

VORSICHT:

Die folgenden Sicherheitsvorschriften müssen vor Inbetriebnahme und in jedem Betriebszustand bei

Service oder Reparatur beachtet werden. Missachtung der Sicherheitsvorschriften undWarnhinweise

aus diesem Handbuch führen zur Verletzung der bestehenden Sicherheitsstandards. Bei Betrieb

des Gerätes außerhalb des bestimmungsgemäßen Einsatzes können die im Gerät integrierten

Schutzfunktionen beeinträchtigt werden. TDK-Lambda ist nicht haftbar für Schäden, die durch

Missachtung dieser Sicherheitsvorschriften entstehen können.

CAUTION:

Z+

series units are not authorized for use as critical component in nuclear control systems, life support

systems or equipment for use in hazardous environments without the express written approval of

the managing director of TDK-Lambda.

VORSICHT:

Die Geräte der

Z+

Serie sind ohne ausdrückliche schriftliche Genehmigung des Geschäftsführers von

TDK-Lambda nicht für die Benutzung als kritische Komponente in nuklearen Steuerungssystemen,

lebenserhaltenden Systemen oder Geräten für den Einsatz in gefährlichen Umgebungen zugelassen.

OVERVOLTAGE CATEGORY AND ENVIRONMENTAL CONDITIONS

The Z+series units have been evaluated to Overvoltage category II.

The Z+series units are intended for use in the following operation conditions:

* Indoor use

* Pollution degree 2

* Max. operational altitude: 3000m above sea level

* Ambient temperature: 0°C-50°C.

ÜBERSPANNUNGSKATEGORIE UND UMWELTBEDINGUNGEN

Die Geräte der Z+Serie wurden hinsichtlich der Uberspannungskategorie II klassifiziert.

Die Geräte der Z+Serie sind zur Benutzung unter folgenden Betriebsbedingungen vorgesehen:

* Benutzung in Innenräumen

* Verschmutzungsgrad 2

* Maximale geografische Höhe für den Betrieb: 3000 m über Null

* Umgebungstemperatur: 0 °C – 50 °C.

GROUNDING

Z+series units are Class I product. To minimize electrical shock hazard, the Z+series units must be

connected to an electrical ground. The instruments must be connected to the AC power supply

mains through a standard certified three-wire power cable, with the ground wire firmly connected

to an electrical ground (safety ground) at the power outlet. Any interruption of the protective

ground conductor or disconnection of the protective earth terminal will cause a potential shock

hazard that might cause personal injury.

ERDUNG

Gerate der Z+Serie sind Produkte der Schutzkklasse I. Zur Minimierung der Stromschlaggefahr

müssen die Gerate der Z+ Serie elektrisch geerdet werden. Die Geräte müssen über ein genormtes,

dreiadriges Netzkabel angeschlossen werden. Die Erdungsleitung des Netzkabels muss mit dem

Erdungskontakt der Steckdose sicher verbunden sein. Eine Unterbrechung der Erdungsverbindung

der Stromversorgung kann die potentielle Gefahr eines elektrischen Schlags zur Folge haben.

LIVE CIRCUITS

Operating personnel must not remove the Z+series unit cover.

No internal adjustment or component replacement is allowed by non-TDK-Lambda qualified

service personnel. Never replace components with power cable connected. To avoid injuries,

always disconnect power, discharge circuits and remove external voltage sources before touching

components.

SPANNUNGSFÜHRENDE Teile

Das Gehäuse der Z+Geräte darf von Anwendern nicht geöffnet werden.

Modifikationen sowie der Austausch von Bauteilen ist ausschließlich qualifizierten

Mitarbeitern der TDK-Lambda erlaubt.

UmVerletzungen zu vermeiden, sind vor Arbeiten im Gerät alle Anschlüsse zu trennen, Kapazitäten

zu entladen und Fremdspannungsquellen zu entfernen.

This manual suits for next models

Table of contents

Other TDK-Lambada Power Supply manuals

TDK-Lambada

TDK-Lambada HWS?HWS User manual

Popular Power Supply manuals by other brands

Monacor

Monacor PS-12CCD instruction manual

VOLTIMA

VOLTIMA MagicBox 15 Installation and operating instructions

Agilent Technologies

Agilent Technologies 6032A Service manual

Miller

Miller Auto Deltaweld 452 owner's manual

BCP

BCP PUOUBK How to install

HC 2210 manual

Puls

Puls CT5.241 installation manual

OCZ

OCZ ZX1250W Technical specifications

iseg

iseg ECH 238 manual

Power

Power XXL A Series instruction manual

Agilent Technologies

Agilent Technologies 6631B Service manual

Renogy

Renogy PHOENIX 300 user guide

HP 6200B Operating and service manual

Epson

Epson Stylus Scan 2500 Product information sheet

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 manual

Puls

Puls MiniLine ML50.100 instruction manual

Puls

Puls AS-Interface SLA4.100 installation manual

Kenwood

Kenwood PS-60 instruction manual