Task Force AP-PW1450-ZE01 User manual
TASK FORCE
PW1450-ZE01_12/2006_REV.1
PLEASE KEEP THE ORIGINAL BOX, PACKAGING AND RECEIPT.
WARRANTY REGISTRATION BY INTERNET, WWW.ACTIVEPRODUCTS.COM.
www.activeproducts.com / 1-866-990-9918
QUESTIONS, PROBLEMS, MISSING PARTS?
Before returning to your retailer, visit our website or call our customer service at
PURCHASE DATE: _______________ SERIAL#: ___________________________________
CAUTION !
BEFORE OPERATING THIS UNIT, PLEASE READ THIS MANUAL THOROUGHLY
AND RETAIN IT FOR FUTURE REFERENCE.
IF YOU MUST STORE YOUR PRESSURE WASHER IN A PLACE WHERE TEMPERATURE IS
BELOW 41ºF (5ºC), YOU MUST APPLY WINTERIZING PROCEDURE TO PROTECT IT. FAILURE
TO WINTERIZE THE UNIT MAY PERMANENTLY DAMAGE PUMP AND VOID THE WARRANTY.
SEE PAGE 10 FOR WINTERIZING PROCEDURE.
US
1450PSI ELECTRIC PRESSURE WASHER
ITEM: 248901
MODEL NO.: AP-PW1450-ZE01
TM
TM
Max. pressure: 1450PSI
Water flow rate: 1.3GPM
Power source requirement: 120V, 60HZ
Electrical cord: 35’ WITH GFCI
High-pressure hose: 20’
Rated current: 11A
Water supply: COLD TAP WATER
Specifications
TECHNICAL SPECIFICATIONS
Technical specifications
Precautions
Safety Features and Electrical Power Information
Replacement Parts and Diagram
Assembly and Operating Instructions
Using the Accessories
Working with Detergent
Shut Down and Clean-up
Taking a Break
Winterizing and Long-term Storage
Maintaining Your Pressure Washer
Troubleshooting
Warranty
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
1
2
3
4
7
8
9
9
10
11
12
14
TABLE OF CONTENTS
i
When using this product, basic precautions
should always be followed:
Read all the instructions before using the
product.
High-pressure jets can be dangerous if
subject to misuse. The jet must not be
directed at persons or animals.
Water spray must never be directed towards
any electric wiring, devices or directly
towards the pressure washer machine itself
or fatal electric shock may occur.
To reduce the risk of injury, do not operate
the machine near children.
Learn how to stop the machine and release
pressure quickly. Be thoroughly familiar with
the controls.
Stay alert—watch what you are doing.
Wear safety goggles.
For use with cold water supply only. Do not
draw other liquids.
Do not use acids, solvents, or any other
flammable material in this product. These
products can cause physical injuries to the
operator and irreversible damage to the
machine.
To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not
touch plug with wet hands.
The pressure washer should not be used in
areas where gas vapours may be present.
An electric spark could cause an explosion or
fire.
To minimize the amount of water getting into
the pressure washer, the unit should be
placed as far as possible from the cleaning
site during operation.
Avoid accidental starts. Shut power “OFF”
before connecting or disconnecting cord to
electrical outlets.
Do not operate the product when fatigued or
under the influence of alcohol or drugs.
Do not stand on unstable surfaces. Stand
with both feet balanced at all times.
Prior to starting the pressure washer in cold
weather, be sure ice has not formed in any
part of the equipment.
Never carry your pressure washer by the
cord. Do not pull on the cord to disconnect
from the outlet.
To allow free air circulation, the pressure
washer should not be covered during
operation.
The Trigger Gun Safety Lock prevents the
trigger from accidentally being engaged. This
safety feature does not lock trigger in the
“ON” position.
California Proposition 65: This product or its
power cord contains lead, a chemical known
to the State of California to cause cancer,
birth defects or other reproductive harm.
Wash hands after use.
Safety Warnings
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not use with flammable liquids and toxic
chemicals.
Injection Hazard: Equipment can cause
serious injury if the spray penetrates the skin.
Do not point the gun at anyone or any part of
the body. In case of penetration seek medical
aid immediately.
This system is capable of producing
1450PSI. To avoid rupture and injury, do not
operate this pump with components rated
less than 1450PSI working pressure
(including but not limited to spray guns, hose
and hose connections).
Before servicing, cleaning or removal of any
parts, shut “OFF” power and relieve
pressure.
Do not spray electrical apparatus and wiring.
If connection is made to a portable water
system, the system shall be protected
against backflow.
Warnings
•
•
•
•
•
•
IMPORTANT PRECAUTIONS - READ FIRST!
1
Extension cords are not recommended unless
they are plugged into a ground fault
circuit-interrupter found in circuit boxes or
protected receptacles.
Warning
The pressure washer is also equipped with a
main power “ON/OFF” switch located on the
unit. It should always be moved to the “OFF”
position when the pressure washer is not
being used to prevent possible injury or
damage.
Warning
Ground Fault Circuit Interrupter:
This pressure washer has a ground-fault
circuit-interrupter (GFCI) built into the plug of the
power supply cord. This device provides additional
protection from the risk of shock. Should replacement
of the plug or cord become necessary, use only
identical replacement parts that include GFCI
protection.
The pressure washer is equipped with a stop
device that will sense when the trigger on the gun
is released. It will open the power circuit to the motor
and cause the pressure washer motor to stop. Motor
will resume again when trigger is pulled.
Extension Cords
If possible, do not use extension cords with this
product. However, if you must use one, observe all
the warnings and instructions listed below:
Use a sufficient gauge:
Maximum cable length: 50’ = 14 AWG
Use only extension cords that are intended for
outdoor use. These extension cords are identified
by a marking “Acceptable for use with outdoor
appliances; store indoors while not in use.”
Use only extension cords having an electrical rating
not less than the rating of the product.
Do not use damaged extension cords. Examine
extension cord before using and replace if
damaged. Do not abuse extension cord and do not
yank on any cord to disconnect.
Keep cord away from heat and sharp edges.
Always disconnect the extension cord from the
receptacle before disconnecting the product from
the extension cord.
To reduce the risk of electrocution, keep all connec-
tions dry and off the ground. Do not touch plug with
wet hands.
•
•
•
•
•
•
SAFETY FEATURES AND ELECTRICAL POWER INFORMATION
2
ZE01-000-0003
ZE01-090-0002
ZE01-090-0001
ZE01-050-0000
ZE01-090-0003
ZE01-090-0004
ZE01-900-0001
ZE01-900-0002
ZE01-000-0001
High-pressure hose
Gun assembly
Quick-connect coupling & inlet adaptor
Water filter
Adjustable wand
Needle
User manual
Gun/wand holder
Turbo wand
1
1
1
1
1
1
1
1
1
5
4
3
2
6
9
8
7
1
Parts No.
Part NameItem no. Quantity
Parts List
CORNER ITEMS:
8 USER MANUAL
9 NEEDLE
4
1
2
3
5
6
7
REPLACEMENT PARTS AND DIAGRAM
3
Fig. 3
Fig. 2
Fig. 1
Make sure that the ON/OFF switch is in the
“OFF” position.
Separate the adaptor and quick-connect
coupling. Attach inlet adaptor to the machine’s
inlet and attach the quick-connect coupling
onto the garden hose.
Insert the wand into spray gun, and twist 1/4 turn until rectangular tab appears.
Step 1 Step 2
Step 3
Do not draw non-water liquids through the unit. For
use with cold water supply only.
Water hose must be at least a 1/2” in diameter.
Flow rate of water supply must not fall below 2 GPM
(gallons per minute).
Flow rate can be determined by running the water
for one minute into an empty 5-gallon container.
The water supply temperature must not exceed
104°F (40°C).
Water Supply (Cold Water Only)
•
•
•
•
•
Caution
To prolong the life of the unit, it is
recommended to rest the unit 5 minutes
after every 30 minutes of use.
Caution
•
•
•
Never use the pressure washer to draw in
water contaminated with solvents (e.g.
paint thinners, gasoline, oil, etc.).
Dirt in the feed water will damage the unit.
To avoid this risk, we recommend
checking the water filter (located inside
the water inlet; to clean it out see
Maintenance section on page 11).
Always prevent debris from being drawn
into the unit by using a clean water
source and an accessory water filter if
required.
Surface Preparation
Before starting any cleaning task, it is important to inspect the area for objects which could create a
hazard. Remove from the workarea which could be tripped over, such as toys or outdoor furniture.
Ensure that all doors and windows are closed tight.
Assembly Time: 2 minutes / Tools Required: None
ASSEMBLY AND OPERATING INSTRUCTIONS
4
Fig. 6Fig. 5
Fig. 4
Attach the high-pressure hose to the water outlet. Twist tightly to avoid leakage.
Attach garden hose to water supply and turn
water on.
Plug the unit into an outlet. Press “TEST”.
then press “RESET” to assure proper
connection to power.
Step 4
Step 5 Step 6
ASSEMBLY AND OPERATING INSTRUCTIONS – continued
5
Fig.7
Fig.8
Start the pressure washer by turning ON/OFF switch to ON.
Before turning the unit ON, depress the trigger to bleed any trapped air out of the pump and
hose.
Step 7
Step 8
ASSEMBLY AND OPERATING INSTRUCTIONS – continued
6
Fig. 9
Adjusting The Spray
The adjustable spray nozzle can be adjusted
from fan to jet. The spray is adjusted from jet
to fan spray by turning the nozzle as shown
in Fig. 9.
Caution
To prolong the life of the unit, it is
recommended to rest the unit 5 minutes
after every 30 minutes of use.
Caution
Jet spray adjustment is very aggressive. Do
not adjust while spraying. We recommend
that for most cleaning applications a 20º
spray angle should be used to avoid
damage to the surface being sprayed.
USING THE ACCESSORIES
7
Cleanup Instructions
Step 1
Insert the detergent suction tube into a container
of fresh water.
Step 2
Set the nozzle to the low-pressure setting.
Step 3
Pull and hold the gun trigger for 20~30 seconds.
Allow fresh water to rinse through the detergent
injection system.
Warning
•Never use bleach, chlorine products
and other corrosive chemicals.
•Never use liquids containing solvents
(i.e., paint thinners, gasoline, oils).
•Never use ammonia products.
•Never use acid-based products.
These products can cause physical
injuries to the operator and irreversible
damage to the machine and/or
damage the surface being cleaned.
Important notice
When you have finished using detergent, always
follow the “Cleanup Instructions”. Failure to
clean properly will cause the injection system to
become clogged and inoperable.
Caution
This machine has been designed for use with
pressure washer detergents only. The use of
other detergents or chemicals may affect the
operation of the machine and will void the
warranty.
Fig.10
Detergent Application
Step 1
Pull the detergent suction tube out and
insert it into a detergent container.
Step 2
Step 3
Adjust the nozzle to low-pressure setting to
apply the detergent.
Step 4
Depress the gun trigger and the detergent will
be automatically injected and mixed with water.
Step 5
Apply detergent to work area. Do not allow
detergent to dry on surface.
Release the gun trigger and adjust nozzle
to high pressure setting. Depress the gun
trigger and rinse the surface in a sweeping
motion.
Note: To apply detergent, the adjustable
nozzle must be in the low-pressure position.
To enhance the efficiency of the pressure washer,
sometimes it is necessary to use detergents to
help loosen tough dirt and grime.
Using the detergent
WORKING WITH DETERGENTS
8
Table of contents
Other Task Force Pressure Washer manuals
