System air SAVE VTR 100/B User manual

Document translated from English | 212234 · A001

SAVE VTR 100/B Electrical reheater installation

GB Installation instructions ................................2

SV Installationsinstruktion .................................8

DE Installationsanleitung.................................14

NO Montasjeanvisning ....................................20

FI Asennusohjeet ..........................................26

212234 | A001

E&OE

Systemair UAB reserves the rights to change their products without notice.

This also applies to products already ordered, as long as it does not affect the previously agreed specifications.

Systemair is not liable or bound by the warranty if these instructions are not adhered to during installation or service.

212234 | A001

Contents

1 Installation.....................................................5

1.1 TRIAC installation (right-hand

orientation)...........................................6

1.2 TRIAC installation (left-hand

orientation)...........................................7

2 Configuration .................................................7

GB Installation | 5

1 Installation

Danger

• Make sure that the mains supply to the unit is disconnected before performing any maintenance or

electrical work!

• All electrical connections and maintenance work must be carried out by an authorized installer and in

accordance with local rules and regulations.

Warning

• Beware of sharp edges during mounting and maintenance. Use protective gloves.

1 Remove the cover of the unit.

Insert reheater (1).

2 Use included plastic knob (2) to secure inserted re-

heater in place. Connect cable from reheater to con-

nector at the top of compartment (3).

Cable contains control signal wires and wires from an

overheat protection sensor.

3 Install and connect TRIAC (component responsible for

temperature detection). Installation method and posi-

tion differs based on VTR 100/B unit orientation.

212234 | A001

6| Installation GB

1.1 TRIAC installation (right-hand orientation)

1RIGHT-HAND ORIENTATION (default from factory, out-

door air connection is situated on the right-hand side

of the unit when viewed from the front)

Remove a screw from the panel inside (1).

Slightly lift and remove the panel (2) in order to ac-

cess the main circuit board.

Peel off label which covers a hole for TRIAC (3).

2 Lift the main circuit board off the hooks (1) and care-

fully pull it out.

Lead TRIAC (2) wires through the hole in the previ-

ously removed panel, insert TRIAC and use included

screws (3) to secure TRIAC in place.

Note:

Make sure TRIAC is facing the correct

direction. Cables must face the main circuit

board.

Connect wires to the main circuit board connector (4).

See wiring diagram for more information.

3 Insert back the main circuit board together with the

panel.

Note:

Make sure not to damage connected the

wires.

Tighten the panel with previously removed screw.

Put the cover back.

212234 | A001

GB Configuration | 7

1.2 TRIAC installation (left-hand orientation)

1LEFT-HAND ORIENTATION (outdoor air connection is

situated on the left-hand side of the unit when

viewed from the front)

Remove a screw from the front panel (1).

Peel off label which covers holes for TRIAC screws.

Position TRIAC (2) over holes and use included screws

(3) to secure TRIAC in place.

Lift the main circuit board off the hooks (5) and care-

fully pull it out.

Connect wires to the main circuit board connector (4).

See wiring diagram for more information.

Insert back the main circuit board.

Tighten the panel with previously removed screw (1).

Put the cover back.

2 Configuration

1. Go to Service menu

2. Enter password (default 1111)

3. Go to Components menu, select Heater menu and select type as Electrical. Do advanced settings if necessary.

4. Configure overheat protection sensor. Go back to Input menu. Select ANALOG tab. Select the analog input to which

the overheat protection sensor is connected. Example if it is connected to AI4 on the main circuit board, then select

ANALOG INPUT 4 and select Overheat Temperature Sensor (OHT) from the input type list.

5. Configure TRIAC. Go to Output menu. Select ANALOG tab then select TRIAC OUTPUT and set output type as Y1

Heating.

Note:

If the supply air temperature is low, it can indicate that the over heat protection is triggered. The overheat

protection can be reset by pressing the reset button.

212234 | A001

2122341 | A001

Alla rättigheter förbehållna

Med förbehåll för eventuella fel och förbiseenden

Systemair AB förbehåller sig rätten att ändra produkterna utan föregående meddelande.

Detta gäller även redan beställda produkter, så länge det inte påverkar tidigare överenskomna specifikationer.

Systemair kan inte hållas ansvarigt för eventuella skador eller följdskador och garantin upphör att gälla om dessa anvisningar inte följs

vid installation eller vid service.

2122341 | A001

Innehåll

1 Installation................................................... 11

1.1 TRIAC-installation

(högerutförande) ................................. 12

1.2 TRIAC-installation

(vänsterutförande) ............................... 13

2 Konfiguration ............................................... 13

Other manuals for SAVE VTR 100/B

Table of contents

Languages:

Other System air Fan manuals

System air

System air PRF User manual

System air

System air Villavent 251-10/B Operating instructions

System air

System air Fantech FLEX VHR 100R ES User manual

System air

System air ERV RT-EC Series User manual

System air

System air SAVE VTC 500 User manual

System air

System air SAVE VTR 300/B User manual

System air

System air Villavent VR-700 E User manual

System air

System air TFSR Manual

System air

System air MAXK Series User manual

System air

System air Fantech SHR200 User manual

System air

System air RVF 100 Manual

System air

System air fantech VER 150 User manual

System air

System air SAVE VTR 300/B User manual

System air

System air PRF 125D2 User manual

System air

System air Fantech DPV22-2 User manual

System air

System air HELLA User manual

System air

System air SAVE VTC 300 User manual

System air

System air SAVE VTR 275/B User manual

System air

System air SAVE VTR 250/B User manual

System air

System air fantech FG EC Series User manual

System air

System air Fantech FKD Series User manual

System air

System air SAVE VSR 300 User manual

System air

System air KBR 315EC User manual

System air

System air Ex 140-2 Troubleshooting guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual