SYMA GYRO REMOTE CONTROL SERIES User manual
8+
1
4-CHANNEL PRESSURE FIXED POSITION HOVERING REMOTE CONTROL DRONE
GYRO REMOTE CONTROL SERIES
X
23W
USER MANUAL
MAIN FEATURES
● Utilizes the 4-axis structure, enabling the drone to be even more
flexible, speedy.It can fly indoor.
● Built-in 6-axis gyro stabilizer to ensure accurate positioning
in-flight.
● The structure uses a modular design which makes it easy to
install and repair.
● Headless function making it easy for directional control.
● 360° stunt flip.
● Pressure-fixed-position hovering function for Auto Hover Mode.
● Auto take-off and landing.
● HD real-time transmission aerial for getting the fun of
different photography.
-1-
1. Please store the smaller-sized drone accessories in places that are out
of reach of children.
2. This drone is very powerful. For all first-time flights, the left joystick
must be slowly pushed up in order to prevent the drone from ascending
too fast to avoid unnecessary collision and possible damage or injury.
3. When the flight is ended, first turn off the power of the remote control.
Then turn off the power of the drone.
4. Avoid placing the batteries in places with high temperatures and
exposure to heat.
5. Take extra precaution to ensure that the drone is at a minimum distance
of 15 feet from the pilot, other people, and animals in order to prevent
bodily injury during flight operation.A minimum separation distance of 20
cm must be maintained between the user's body and the device under
normal use condition.
6. This drone is for people ages 8+. It must be flown always within the
line of sight of the pilot (or instructor) and flown safely.
7. Non-rechargeable batteries are not to be recharged;Batteries are to be
inserted with the correct polarity;Different types of batteries or new and
used batteries are not to be mixed.
8. When the drone is not in use, please remove the batteries in the remote
control.
9. The supply terminals are not to be short-circuited.
10.Discharge the battery to 40%-50%（On a full charge, fly for half of the
total flight time） if it will not be used for 10 days or more，this can
greatly extend the battery life.
11.Please keep a safe distance from the spinning propellers to avoid injury.
12.To ensure the electromagnetic environment requirement of the aviation radio
(station), using remote controls in the zone, which is in a radius of about
5000m zone from the circle center of the airport runway, is forbidden. All
users also should abide by the regulation of the radio set forth by government
and regulatory agencies including the duration and area.
13.Only uses the recommended transformer for the model, and the transformer
is not a model. Disconnect the transformer from the model which is available
cleaning with liquids before cleaning. Check the cord, plug, enclosure and
other parts of the transformer regularly. If any damages have been discov
ered, please immediately stop using it, until it was completely repaired.
14.Never look steadily at the laser beam since the laser radiation.
15.Attention：Drone assembly under adult supervision.
16.The pilot is responsible for the safe operation and safe distance from
uninvolved persons and property on the ground and from other airspace
users and shall never fly the drone above crowds (> 12 persons).
17.The packing has to be kept since it contains important information.
1. Use dry and soft cloth to clean this product.
2. Avoid exposing this product to heat.
3. Do not immerse this product in water, otherwise, the electronic parts will be damaged.
4.Transformers used with the toy are to be regularly examined for damage to the cord,
plug,enclosure and other parts,and that,in the event of such damage,the toys must be
used with this transformer until the damage has been repaired.
Safety Guide
Repair and maintenance
-2-
2. Press the flexible
accessory latch on
the battery and pull
it backwards
3. Align the charging head
of the USB charging
cable with the charging
port of the battery
The following items can be found in this product package:
Package Description
• Drone
• Remote Control
• Instruction Manual
• Main Blades
• USB Charging Cable
• Mobile Phone
Retaining Clip
Phone Clip Attachment/Removal Method
Phone clip holder
installation:
1.Insert the phone clip holder
into the connector at the
top of the remote control.
Phone clip holder
removal:
3.Hold the elastic
accessory lock on the
back of the phone clip
and pull it out.
Battery Changing And
Charging Methods For Drone
Battery changing methods for drone
1.Press the power button on
the top of the drone to 1-2S
make sure the drone is
turned “OFF”.
Battery charging methods for drone
Connect the battery cord to the USB, then
connect the USB interface to the computer.
(The indicator light of the drone will turn on
while charging,and turn off when charging
completed.It takes about 130 minutes to
completely charge the battery. )
2. Press the handles to
adjust the jaws.
-3-
The charging time is about 130 minutes; Hover flight time
is approximately 7 minutes.
Precautions as follows during charging of battery:
Understanding Your Remote Control
Remote control’s button function description:
Battery installation for remote control:
Power ON/OFF
Mobile Phone
Retanining Clip
Battery cover
4 x AA Alkaline Batteries
- Avoid placing the active batteries in places with direct exposure, sunlight and
high temperatures. For example, naked light or electrical equipment
installations; otherwise it may cause damages or explosions .
- Avoid immersing the batteries in the water. The batteries shall be stored in a
cool and dry place.
- Avoid dismantling the batteries.
- During the charging of battery, avoid leaving the charging place.
- Rechargeable batteries are to be removed from the toy before being charged.
- Rechargeable batteries are only to be charged under adult supervision.
Auto take-off and landing
Right Joystick
Press and hold to
enter / exit headless mode
Press to change high / low
speed
360º Stunt flip
Left Joystick
Keep pushing in until
trimming control finshed.
To clear all the trimming
setting, keep pushing
and press the power
button at the same time.
1. Battery Installation Method: Open up the battery cover at the back of the remote
control. Correctly place 4 x AA alkaline batteries in the battery box in strict
adherence to the polarity instructions (the AA alkaline batteries are not included).
1. During the battery installation, it must be ensured that the polarities of
the batteries are matched with that of the battery box. No battery shall
be installed with the opposite polarity.
2. Do not use new and old batteries together.
3. Different types of batteries are not be mixed.
4. Do not use rechargeable batteries.
-4-
Step 2: Press the power button on the top of
the drone to 1-2S make sure the
drone is turned “ON”.
Flight Preparation And Switching
The Drone On And Off
1. Flight Preparation
Step 1: Press the power button of the remote
control.
Step 3: Push the left joystick (accelerator) up to the
highest point and then push down to the
lowest point. When the led indicator lights in
the drone change from quick flashing to
continuous light, it means that the drone goes
into the flight standby mode.
-5-
3. Turning off the drone
Method 3: When the drone is in flight, press
button B, the drone will descend to
the ground and lands.
Method 3: When the drone is stationary,press
the B button, the drone automatically
takes off and hovers at a certain
height.
2. Turning on the drone
1.If the drone is out of the range of the flight, the indicator light will
flash slowly, and then slow down.
2.When the remote control is switched off or the power is cut off, the
drone will automatically slow down to stop.In the process , open
the remote control to control again.
Method 1:Push the left joystick (throttle)
to the highest point and then
back to the center, the blades
of the drone start rotating slowly.
Method 2:Push the left and right joysticks
to the bottom inner corners for 1
second, the blades of the drone
start rotating slowly.
Method 2:Push the left and right joysticks
to the bottom inner corners for
1 second, and the drone can be
turned off.
Method 1:Push the left joystick (throttle) to
the lowest level and hold for 2 to
3 seconds, the drone can then be
turned off.
-6-
Operating direction
Drone Controlling Diagram
Ascending and descending control Forward and backward control
Trimming operation
Left turning and right turning control Left side flying and right side flying
control
When the left joystick (throttle) is
pushed upwards or downwards,
the drone will ascend or descend
correspondingly.
When the right joystick (rudder) is
pushed upwards or downwards,
the drone will fly forward or
backward correspondingly.
When the left joystick (throttle) is
pushed towards the left or right,
the drone will turn left or right
correspondingly.
When the right joystick (rudder) is
pushed towards the left or right,
the drone will fly sideways on the
left or right correspondingly.
If the drone automatically flies forward/backward
while hovering, press in the left joystick and at the
same time push the right joystick backward/forward
slightly to fine tune the direction. Don’t release the
left joystick until the drone is flying in a stable state.
Forward and backward trim control
-7-
Product features
1. Low-voltage protection:
2.Over-Current Protection:
3.Level Calibration Function:
When the four indicator lights at the bottom of drone
start flashing, it means that the drone's battery power is
low. At this time, please control the drone return.
Place the drone on a level surface and at the same
time, push both left and right joysticks to the lower right
corners for 2 to 3 seconds; the indicator lights on the
drone will blink rapidly, and they will return to solid
status after about 2 to 3 seconds. The level calibration is
successful.
4.High/Low Speed Function:
Low speed by default when first powered-on. Possible to
switch the function mode of high/low speed by pressing
the right joystick for a short time. It is switched into high
speed mode when two ”beep” sounds come from the
remote control, pressing the right joystick for a short time
under fast speed mode and then one “beep” sound would
come from the remote control,then it is switched back into
low speed mode.
If the drone automatically flies towards the left/right side
while hovering, press in the left joystick and at the same
time push the right joystick right/left slightly to fine tune the
direction. Don’t release the left joystick until the drone is
flying in a stable state.
If the drone automatically rotates and flies towards the
left/right side while hovering, press in the left joystick and
at the same time move it to the right/left slightly to fine
tune the direction. Don’t release the left joystick until the
drone is flying in a stable state.
Left/right side turning trim control
Left/right side flight trim control
When the drone encounters direct impact from a foreign
object, or is obstructed, or the blades are not rotating, the
drone will go into the over-current protection mode.
-8-
3M
Front
Back
Left Right
5. 360° Stunt Flip Function:
Note: Drone will have the best stunt flip action when the batteries are fully charged.
6. Auto Hover Function:
When you are familiar with the basic actions, you can
proceed to explore even more exciting stunt actions. Fly the
drone to a height of 3M above the ground, push the upper
right corner button (Stunt Flip Button) on the remote control
and simultaneously push the right joystick to the farthest
position of Front/Back/Left/Right, the drone will now execute
the Front/Back/Left/Right stunt flip action.
7. Headless function:
A. Defining forward direction:
a. Press on the power button of the remote control.
B. Calibration for the definition of the front:
c. Push the left joystick (throttle) on the remote control
up to the farthest position and then pull down to the
farthest position. When the remote control issues a long
beep sound, it means the frequency and defining
forward direction functions are completed.
b. Press the power button on the top of the drone to 1-2s
make sure the drone is turned“ON”, and adjust the
specified direction of the drone’s head under the headless
mode as the new forward direction.
After using the left joystick (throttle) to control the
ascending/descending flight of the drone, release
the left joystick (throttle) and the drone will hover at
that height when the joystick is released.
a. When the drone encounters a direct impact with
foreign objects in the headless mode, if there is an
occurrence of deviation of the defined direction, it is
only required to push both the left and right joysticks
to the bottom left corners simultaneously after placing
the flying direction of the drone in the correction
position. When the led light indicator of the drone is in
a long “ON” mode after slowly flashing for 3 seconds,
it indicates the calibration is complete.
-9-
C. Toggling between headless function and normal function:
1. After the drone is matched with the corresponding
frequency, the drone would be in normal pattern by default. At
this time the indicator light on the drone would be in a state of
on for a long time. After pressing in on the right joystick of the
remote control for 2 seconds, the remote control would make
a sound of “beep, beep, beep” to show that it has entered into
a state of headless mode.Pressing in on right joystick for 2
seconds then a long sound of “beep” would be heard to show
an exit status.(When under the state of headless mode, four
indicator lights on the drone are led lights which flicker once
every four seconds)
2. Under the headless mode, the operator does not need to
differentiate the head position of the drone, and only needs
to control the drone's direction front/back/left/right by using
the right joystick direction on the remote control.
Front
Back
Left Right
Front
Left
Back
Right
Front
Left
Back
Right
8.Wireless real-time transmission funtion
1.Downloading the installation software
For Android phones,download and install the SYMA GO APP by visiting
the www.symatoys.com or by scanning the QR code.
For IOS Apple phones,download and install the SYMA GO APP by visiting
the App Store or by scanning the QR code.
1.Connect the model to its power source, the camera indicator light should turn
green. Within 10 seconds, the light will flash slowly and the camera will be
waitting for a connection with a smartphone.
2.At this time, enter the “Settings” option on your phone, and turn on WLAN. In
the WLAN search list, look for a network called “FPV-WIFI- ****” and connect to
it. Once connection has been established, exit the “Settings” option.
3.Open the SYMA GO App, click the “START” icon to enter the control interface.
A full bar in the WiFi signal strenght icon indicates the strongest possible signal.
2.How to connect
1. Open up SYMA GO
APP.
3. The phone’s screen
will display real-time
images.
2. Click the "START" icon,
the system will enter the
APP operation interface
automatically.
Reminder: QR codes are provided on the packaging box and at the bottom of
the user manual. Please visit website www.symatoys.com or the App
Store/Google Play to obtain the newest SYMA GO App.
Other manuals for GYRO REMOTE CONTROL SERIES
4
This manual suits for next models
1
Table of contents
Other SYMA Drone manuals
