Suntex EC-4110 User manual
1
EC-4110
ʳ
Intelligent
ʳ ʳ
Conductivity
Transmitter
Operation
Manual
Precautions for installation
Wrong wiring will lead to breakdown or electrical shock of the instrument, please read this
operation manual clearly before installation.
zMake sure to remove AC power from the controller before wiring input, output connections,
and remove it before opening the controller housing.
zThe installation site of the controller should be good in ventilation and avoid direct sunshine.
zThe material of signal cable should be special coaxial cable. Strongly recommend using our
coaxial cable. Do not use normal wires instead.
zAvoid electrical surge when using power. Especially when using three-phase power, use
ground wire correctly.
zThe internal relay contact of the instruments is for alarm or control function. Due to safety,
please must connect to external relay which can stand enough ampere to make sure the safety
operation of the instruments.˄Please refer to chapter 3.6ʳ“Illustration of electrical
connectionϙ˅
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Precautions for installation
Brief Instruction
1
1. Specifications 4
2. Assembly and installation
2.1 Transmitter installation 5
2.2 Illustration of panel mounting 5
2.3 Illustration of Wall mounting and pipe mounting 6
3. Overview of conductivity / resistivity transmitter EC-4110
3.1 Illustration of rear panel 7
3.2 Illustration of terminal function ˊ
3.3 Description of terminal function ˋ
3.4 Wiring of cable ˌ
3.5 Circuit of cable ˌ
3.6 Illustration of electrical connection 10
4. Configuration
4.1 Illustration of front panel 11
4.2 Keypad 11
4.3 LED indicators 11
4.4 Display 12
5. Operation
5.1 Measurement mode 13
5.2 Set-up menu 13
5.3 Calibration menu 13
5.4 Shortcuts 13
5.5 Reset 13
5.5.1 Set-up reset 13
5.5.2 Calibration reset 13
6. Settings
Block diagram of settings 14
6.1 Entry of set-up menu 16
6.2 Security code of settings(Code) 17
6.3 Measurement parameters(Mode) 18
6.4 Temperature 19
6.5 Compensation 20
6.6 Relay 1 21
6.7 Relay 2 22
CONTENTS
6.8 Wash time(Clean) 23
6.9 Analog output 1 (Cond/Res) 24
6.10 Analog output 2 (˧emperature) 25
6.11 Date/Time (Clock) 26
6.12 Sample average of measurements (Digital filter) 27
6.13 Backlight settings 28
6.14 Contrast settings 29
6.15 Power frequency (Freq.) 30
6.16 Automatically back to measurement mode(Return) 31
7. Calibration
Block diagram of Calibration 32
7.1 Entry of calibration menu 33
7.2 Automatically back to measurement mode(Return) 34
7.3 Security password of calibration 35
7.4 Cell constant calibration (CELL Const.) 36
7.4.1 Resistivity (Res) 36
7.4.2 Conductivity (Cond) 37
7.5 Standard solution calibration (Std. Sol.) 38
8. Error messages (Error code) 39
9. Installation of cells
9.1 Appearance of cells 40
9.2 Correct installation 40
9.3 Incorrect installation 41
Brief Instruction
Description of set-up settings (see chapter 6 for details) ʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳʳ
Press and simultaneously to see the overview of the set-up settings now. Then press I
if you would like to modify set-up settings. Press keypad according to index of keypad on the screen.
Index of keypad
keypad Accordingly item Description
Back to upper layer
Choose leftward of change to left page
Increase digit
Choose rightward of change to right page
Decrease digit
Confirm settings after modifications and then go through next
step
Selection of set-up items
keypad Accordingly item Description
Mode Measurement mode, to choose Resistivity (Res) or Conductivity
(Cond) measurement
Temperature Temperature measurement and compensation, including MTC,
PTC, NTC (3 types total). MTC---Manual temperature
compensation, PTC/NTC--- auto temperature compensation
Relay 1 First relay setting, to choose action off or Hi/Lo alarm
Relay 2 Second relay setting, to choose action off or Hi/Lo alarm
Clean Automatic wash time setting, to choose electrode clean
equipment’s ON and OFF duration
Analog 1 Current output according to Res or Cond setting range
Analog 2 Current output according to temperature setting range
к
Clock Clock setting (When out of power and reboot it, the
instrument’s time setting will return to the factory
pre-setting)
Black-light Backlight setting, to set Auto/ON/OFF backlight, brightness,
and sensitivity
Contrast Contrast of screen setting
Digital Filter Take every serial 1~60 measurements, average them
continuously, and make it as the readings
Return Setting of returning to the measurement mode
Code Security code of set-up mode. The factory default is 1111, and a
designated user can change the code. The set-up code is
precedential to calibration code, thus it can pass a different
security code of calibration.
л
Description of calibration settings (see chapter 7 for details)ʳ ʳʳʳʳʳʳʳʳʳʳʳʳʳ
Press and simultaneously to see the last calibration information. Then press if you
would like to make a new calibration or modify setting of calibration. Press keypad according to
index of keypad on the screen.
Index of keypad:
keypad Accordingly item Description
Back to upper layer
Choose leftward of change to left page
Increase digit
Choose rightward of change to right page
Decrease digit
Confirm settings after modifications and then go through next
step
Selection of calibration items (up to three-point calibration)
keypad Accordingly item Description
Code Security code of calibration mode. The factory default is 1100.
Return Time interval setting of returning to the measurement mode
Cell Constant To adjust the instrument cell constant setting until the value the
same with the given cell constant of the sensor
Solution Use the appropriate standard solution to calibrate the system
Note ʳ
SUNTEX reserves the right to change the figure of icons and contents. The actual icons and contents
please refer to the instruments.
м
1. Specifications
Model
!
EC-4110
Measuring modes
!
Resistivity/Conductivity/Temp.
Resistivity 0.00 M·cm~20.00 M·cm
Conductivity 0.00 S/cm~200.0 mS/cm manual or auto range selectable
Ranges
!
Temp.
!
-30.0~130.0˚C
Resistivity 0.01 M·cm
Conductivity 0.01 S/cm
Resolutions
!
Temp.
!
0.1˚C
Resistivity ±1% ±1Digit
Conductivity ±1% ±1Digit
Accuracy
!
Temp.
!
±0.2˚C±1Digit
Temperature
Compensation
!
NTC30K or PT1000 or
Manual temperature compensation selectable
Calibration mode
!
(1)Cell constant adjustment (2)Standard solution calibration
Ambient Temp.
!
0~50 ˚C
Storage Temp.
!
-10~70 ˚C
Cell Constant
!
0.01, 0.05, 0.1, 0.5, 10.00 cm-1 fixed,
freely selectable 0.008~19.99 cm-1
Temperature Coefficient
!
Linear temperature compensation from (0.00%~ 40.00%)
and Non-Linear compensation
Display
!
Large LCD display with environment light sensor
auto/manual illumination function
Analog output 1
!
Isolated DC 0/4~20mA corresponding to main measurement,
max. load 500:
Analog output 2
!
Isolated DC 0/4~20mA corresponding to Temp., max. load 500:
Contact
!
RELAY contactΔ240VAC 0.5A Max.(recommend)
Settings
!
Activate
!
Two sets of individual HIGH or LOW programmable control
Wash RELAY contact: ON 0~99min. 59sec. / OFF 0~999hr 59min.
Certification IP65 (NEMA 4)
Power Supply 100V~240VAC±10%Δ50/60HzΔ5W max.
Installation Wall or Pipe or Panel Mounting
Dimensions 96m × 96mm × 132mm (HuWuD)
Cut off Dimensions 93 mm u93 mm (HuW)
Weight 0.5Kg
Note: The specifications are subject to change without notice.
н
2. Assembly and installation
2.1 Transmitter installation: This Transmitter can be installed through panel mounting, wall
mounting and pipe mounting.
Installation of panel mounting: Firstʿprepare a square hole of 93 x 93mm on the panel box,
and then insert the controller directly into the panel box. Insert the accessorial mounting bracket
from the rear, and make it be fixed in to pickup groove.
2.2 Illustration of panel mounting:
93 mm
93 m
m
Hole size
87 mm
Ѐ
87 mm
Hole distances on the
p
anel box
Mounting bracket
Illustration of panel mounting,
fixed with mounting bracketʳ
Ѐ
ЀЀ
112 m
m
о
2.3 Illustration of Wall mounting and pipe mounting
Installation of pipe mounting
Fixed with U-shaped pipe clip. The
distance between screw holes is 60mm
Installation of wall mounting
Fixed with 4 x M4 screws
Sun Shield (Pipe mounting)
(Optional)
Sun Shield (Wall mounting)
(Optional)
п
This manual suits for next models
1
Table of contents
Other Suntex Transmitter manuals
Suntex
Suntex EC-4110-I User manual
Suntex
Suntex PC-3110-P User manual
Suntex
Suntex TC-7310-RS User manual
Suntex
Suntex PC-300A Series User manual
Suntex
Suntex CT-6300 User manual
Suntex
Suntex CT-6300RS User manual
Suntex
Suntex PC-3110-RS User manual
Suntex
Suntex PC-3310 Installation manual
Suntex
Suntex CT-6110-POL User manual
Suntex
Suntex IT-8100 User manual
Popular Transmitter manuals by other brands
Dejero
Dejero EnGo 3x manual
Rosemount
Rosemount 4600 Reference manual
Speaka Professional
Speaka Professional 2342740 operating instructions
trubomat
trubomat GAB 1000 instruction manual
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 instructions
Rondish
Rondish UT-11 quick start guide
