Subaru 2017 Legacy User manual
37
BASIC FUNCTION
2
2
docstructure.indb 37 2016/03/30 11:15:16
BASIC INFORMATION BEFORE OPERATION
38
BASIC INFORMATION BEFORE OPERATION
INITIAL SCREEN
INITIAL SCREEN
WARNING
lWhen the vehicle is stopped with the engine running, always
apply the parking brake for safety.
1. When the ignition switch is in the “ACC” or “ON”
position, the initial screen will be displayed and the
system will begin operating.
●After a few seconds, the “CAUTION (CAUTION)”
screen will be displayed.
2. Select
I Agree
(I Agree).
●After about 5 seconds, the “CAUTION (CAUTION)”
screen automatically switches to the next screen.
●With navigation function: Select
Language
(Language) to select a language.
XWith navigation function
3. Select
Accept
(Accept).
● Conrm the end-user license agreement.
docstructure.indb 38 2016/03/30 11:15:17
BASIC INFORMATION BEFORE OPERATION
39
BASIC FUNCTION
2
4. Select
Next
(Next).
● The “Conguration Wizard (Conguration Wizard)”
starts.
5. Select the desired language and narrator. Select
Next
(Next) to continue.
●When the “TTS Voice (TTS Voice)” mode is selected,
the voice control navigation and street guidance
can be used. These functions cannot be used when
the “Natural Voice (Natural Voice)” mode is selected.
●You can change this at any time from “Sound and
Warnings (Sound and Warnings)” settings. (→P.241)
6. Change the unit settings if necessary. Select
Next
(Next) to continue.
●You can change this at any time from “Units and
Formats (Units and Formats)”. (→P.244)
7. Change the initial route plan settings if necessary.
Select
Next
(Next) to continue.
●You can change this at any time from “Route Settings
(Route Settings)”. (→P.231)
docstructure.indb 39 2016/03/30 11:15:17
BASIC INFORMATION BEFORE OPERATION
40
8. Select
Finish
(Finish).
● After setting up, you can run the “Conguration
Wizard (Conguration Wizard)” at any time from
the “Settings (Settings)” menu. (→P.240)
MAINTENANCE INFORMATION
This system reminds users when to replace certain parts or
components and shows dealer information (if registered) on
the screen.
When the vehicle reaches a previously set driving distance
or date* specied for a scheduled maintenance check, the
“Maintenance Reminder (Maintenance Reminder)” screen
will be displayed when the system is turned on.
*: With navigation function
●The screen goes off if the screen is not operated for
several seconds.
●To prevent the screen from being displayed again,
select
Do Not Tell Me Again
(Do Not Tell Me
Again).
● To register maintenance information: →P.196
●If is selected, the registered phone number can
be called.
docstructure.indb 40 2016/03/30 11:15:18
BASIC INFORMATION BEFORE OPERATION
41
BASIC FUNCTION
2
LOADING AND UNLOADING A DISC
LOADING A DISC
CAUTION
lNever try to disassemble or oil any part of the CD player. Do
not insert anything other than a disc into the slot.
1. Insert a disc into the disc slot.
●After insertion, the disc is automatically loaded.
NOTE
lCompatible Disc: →P.103
lWhen inserting a disc, gently insert the disc with the label facing
up.
UNLOADING A DISC
1. Press and remove the disc.
NOTE
lDiscs can be unloaded even when the engine switch is turned
off.
docstructure.indb 41 2016/03/30 11:15:19
BASIC INFORMATION BEFORE OPERATION
42
CONNECTING AND
DISCONNECTING A USB MEMORY/
PORTABLE DEVICE
CONNECTING A DEVICE
1. Connect a device.
USB
AUX
●Turn on the power of the device if it is not turned on.
NOTE
lCompatible USB memory: →P.106
lCompatible iPod: →P.106
lThis unit does not support commercially available USB hubs.
lBy connecting a device such as a cellular phone, charging starts
depending on the device.
LOADING AND REMOVING AN
SD CARD (WITH NAVIGATION
FUNCTION)
LOADING AN SD CARD
CAUTION
lPosition the SD card with the “▲” mark at the far end and
insert it until it clicks into place. When contact is made with the
stopper inside, the card cannot be inserted any further. Do not
try to forcibly push the card.
lDo not insert anything other than an SD card into the slot.
lDo not pull the SD card slot cover with force. By doing so, the
SD card slot cover may come off, or be damaged. If the SD
card slot cover comes off, it can be reattached by inserting the
cover clip into the hole.
lAvoid touching the SD card terminals to prevent
contamination. Doing so may cause card read failure.
docstructure.indb 42 2016/03/30 11:15:19
BASIC INFORMATION BEFORE OPERATION
43
BASIC FUNCTION
2
1. Turn the ignition switch to the “OFF” position.
2. Open the SD card slot cover.
3. Insert the SD card.
●Make sure that the SD card is fully inserted.
4. Close the SD card slot cover.
NOTE
lCompatible SD card: →P. 107
lYou can enjoy music/video by inserting an SD card containing
audio les and/or video les. (→P.87)
lYou can preview images, play a slideshow, (→P.87) or set an
image as the screen off images (→P.191) by inserting an SD
card containing image data.
docstructure.indb 43 2016/03/30 11:15:19
BASIC INFORMATION BEFORE OPERATION
44
REMOVING AN SD CARD
CAUTION
lWhen removing an SD card from the unit, pull it out
horizontally. Do not pull it out upward or downward with force.
Doing so may damage the SD card.
lDo not remove an SD card during playback. Doing so may
corrupt the data. Please understand that no compensation will
be given for corrupted data.
lDo not pull the SD card slot cover with force. By doing so, the
SD card slot cover may come off, or be damaged. If the SD
card slot cover comes off, it can be reattached by inserting the
cover clip into the hole.
lAvoid touching the SD card terminals to prevent
contamination. Doing so may cause card read failure.
NOTE
lThe system is reset and the initial screen appears if the map SD
card is removed during use, however, this is not a malfunction.
The map screen appears again approximately 7 seconds after
reinserting the map SD card.
lWhen removing an SD card from the unit and “Auto Adjust by
GPS (Auto Adjust by GPS)” is selected in the Clock Settings
(→P.190), the time on the Climate Control will change to
Greenwich Mean Time (GMT).
1. Turn the ignition switch to the “OFF” position.
2. Open the SD card slot cover.
3. Remove the SD card.
●Press in the SD card until you hear it “click”, let go of
the card, and then pull it straight out.
4. Close the SD card slot cover.
docstructure.indb 44 2016/03/30 11:15:19
BASIC INFORMATION BEFORE OPERATION
45
BASIC FUNCTION
2
TOUCH SCREEN GESTURES
Operations are performed by touching the touch screen
directly with your nger.
Operation method Outline Main use
Touch
Quickly touch
and release
once.
Changing
and selecting
various settings
Double Touch
with one
nger*1
Quickly touch
and release
twice with one
nger.
Enlarging the
scale of the map
screen
Double Touch
with two
ngers*1
Quickly touch
and release
twice with two
ngers.
Reducing the
scale of the map
screen
Operation method Outline Main use
Drag*2
Touch the
screen with
your nger,
and move the
screen to the
desired position.
• Scrolling the
lists
• Scrolling the
map screen*1
Flick*2
Quickly move
the screen by
icking with your
nger.
• Scrolling the
main screen
page
• Scrolling the
map screen*1
Pinch*1
Move your two
ngers further
apart (pinch-
out) to zoom in
the map. Move
your two ngers
closer together
(pinch-in) to
zoom out the
map.
Changing the
scale of the map
screen
docstructure.indb 45 2016/03/30 11:15:20
BASIC INFORMATION BEFORE OPERATION
46
Operation method Outline Main use
Rotate*1
To change the
map direction,
rotate with two
ngers touching
the screen.
Changing the
horizontal
display angle of
the map.
*1: With navigation function
*2: The above operations may not be performed on all screens.
NOTE
lFlick operations may not be performed smoothly in high
altitudes.
TOUCH SCREEN OPERATION
This system is operated mainly by the buttons on the
screen. (Referred to as screen buttons in this manual.)
●When a screen button is touched, a beep sounds.
The beep sound can be turned on or off. (→P.188)
CAUTION
lTo prevent damaging the screen, lightly touch the screen
buttons with your nger.
lDo not use objects other than your nger to touch the screen.
lWipe off ngerprints using a glass cleaning cloth. Do not use
chemical cleaners to clean the screen, as they may damage
the touch screen.
NOTE
lIf the system does not respond to touching a screen button,
move your nger away from the screen and then touch it again.
lDimmed screen buttons cannot be operated.
lThe displayed image may become darker and moving images
may be slightly distorted when the screen is cold.
lIn extremely cold conditions, the map may not be displayed
and the data input by a user may be deleted. Also, the screen
buttons may be harder than usual to depress.
lWhen is displayed on the screen, select to return
to the previous screen.
docstructure.indb 46 2016/03/30 11:15:20
Other manuals for 2017 Legacy
5
Table of contents
Other Subaru Automobile manuals
Subaru
Subaru 2003 Legacy User manual
Subaru
Subaru 2003 Legacy User manual
Subaru
Subaru Impreza 2004 User manual
Subaru
Subaru 2003 Legacy User manual
Subaru
Subaru 2003 Legacy User manual
Subaru
Subaru Ascent 2020 User manual
Subaru
Subaru FORESTER 2.5 X L.L.Bean Edition User manual
Subaru
Subaru A3100BE User manual
Subaru
Subaru Legacy 2015 User manual
Subaru
Subaru 2001 Forester User manual
Subaru
Subaru 2003 Legacy User manual
Subaru
Subaru 2002 Impreza User manual
Subaru
Subaru 2010 Legacy User manual
Subaru
Subaru 2005 Impreza Operating and maintenance instructions
Subaru
Subaru Tribeca User manual
Subaru
Subaru Impreza 2004 User manual
Subaru
Subaru Forester 2.5 XS L.L.BEAN User manual
Subaru
Subaru Legacy 2.5i Premium User manual
Subaru
Subaru 2014 XV Crosstrek User manual
Subaru
Subaru WRX-STI User manual
