Stratasys Objet1000 Plus Operating instructions

DOC-06500 Rev.J

3D Printing System

Site Preparation Guide

Objet1000 Plus

ThisdocumentationcontainsproprietaryinformationofStratasysLtd.Thisinformationis

suppliedsolelytoassistauthorizedusersofthisStratasys3Dprintingsystem.Nopartof

thisdocumentmaybeusedforotherpurposes,anditmaynotbedisclosedtootherparties.

Thespecificationsonwhichthisdocumentisbasedaresubjecttochangewithoutnotice.

Nopartofthisbookmaybereproducedinanyformorbyanymeans,norstoredinadatabase

orretrievalsystem,withoutpriorpermissioninwritingfromStratasysLtd.

IfthisdocumentisdistributedasaPDFfile,youmayprintitforinternaluse.

April2018

DOC-06500Rev.J

Trademarks

ThefollowingareregisteredtrademarksofStratasysLtd.:Stratasys®,Objet®,FullCure®.

Allnamesofproductsandservicescitedinthisbookaretrademarksorregistered

trademarksoftheirrespectivecompanies.

Feedback

Ifyouhaveanyquestionsorcommentsaboutthewayinformationispresentedinthis

document,orifyouhaveanysuggestionsforfutureeditions,pleasesendamessageto

c-support@stratasys.com.

DOC-06500 Rev.J

Contents

Introduction 5

PhysicalDescription 6

SizeandWeight 6

ShipmentandDelivery 7

ShippingInformationandCustomerResponsibility 7

ShippingPallet 7

LiftingEquipment 7

Unloading 8

InstallationArea 10

FloorPlan(PrinterArea) 10

ClientWorkstations 12

ElectricalRequirements 13

Power 13

Grounding 13

CircuitBreaker 14

ResidualCurrentDevice(RCD) 14

PowerConnection 14

UPS(UninterruptedPowerSupply) 15

CommunicationLines 16

LocalAreaNetwork 16

Telephone 16

EnvironmentalConditions 17

TemperatureandHumidity 17

AirQuality 17

NoiseLevel 17

AccessoriesandUtilities 18

Start-UpKit 18

ExhaustAdapter 18

EyewashStation 19

BuildTrayUnloadingCart 19

CompressedAir 20

FireSafetyEquipment 20

MaterialsHandlingandStorage 21

PrintingMaterials 21

DOC-06500 Rev.J 3

CleaningSolvent 21

SitePreparationChecklist 22

DOC-06500 Rev.J 4

Introduction

Theinformationandrequirementsprovidedinthisdocumentensureproperinstallationandoperationof

theObjet1000Plus3Dprintingsystem.Thecustomerisresponsibleforpreparingthesiteas

describedinthisdocument,andaccordingtoanyapplicablelocalregulations.

Ifyouhaveanyquestionsabouttheinformationinthisdocument,contactyourStratasys

representative.

Allsiterequirementsmustbemetbeforetheinstallationdate.TheSitePreparationChecklistshould

besubmittedtoyourStratasysrepresentative.Shippingwillbearrangedafterthechecklistisreceived

byStratasys.

Non-compliancewithrequirementsspecifiedinthisdocumentmayresultinadditionalinstallation

charges.

Objet1000 Plus Introduction

PhysicalDescription

TheObjet1000Plus3Dprintingsystemconsistsofthefollowingmaincomponents:

• printer

• printercomputer(builtintotheprinter)

• printer-serverworkstation(builtintotheprinter)

Figure1Objet1000Plusprinter

SizeandWeight

Thefollowingtableshowsthesizeandweightinformationfortheprinter.

W × H × D (mm) W × H × D (inch) Weight (kg/lb)

2686×1960×2102 105.7×77.2×82.8 2200kg/4850lb

Table1Sizeandweight

• W=Width;H=Height;D=Depth

• Thesedimensionsdonotincludetheoperatorconsoleandthesignaltower.

Objet1000 Plus Physical Description

ShipmentandDelivery

ShippingInformationandCustomerResponsibility

Shipmenttothecustomerwillbearrangedasspecifiedinthepricequote.Thecustomerisresponsible

forprovidingdetaileddeliveryinformation,including,whetherornotthereisloadingdockatthe

deliverysite.

Thecustomerisresponsiblefortransportingtheprintertoasuitableinstallationsite.Thecustomeris

responsibleforensuringthataprofessionalmovertransportstheprintertotheinstallationsite,and

unloads,unpacks,andmovesittoitsfinallocation.Uponrequest,yourStratasysserviceproviderwill

adviseregardingthesematters.

Note:

AStratasys-certifiedcustomersupportengineermustbepresentwhiletheprinteris

beingunloadedandunpacked.

ShippingPallet

Thefollowingtableshowstheapproximatesizeandweightoftheprintingsystemmountedonapallet.

W ×H ×D mm W ×H ×D inch Weight (kg/lb)

3110×2230×2160 122.5×87.8×85 2900kg/6393lb

Table2Sizeandweightofprinteronshippingpallet



W=Width;H=Height;D=Depth



LiftingEquipment

Aforkliftwiththefollowingspecificationsisrequired:

• liftingcapacity:3000kg(6614lb)

• extensions:300cm(118.1in.),asshowninFigure2

Objet1000 Plus Shipment and Delivery

Unloading

Theunloadingareashouldbealevelsurface.

Aclearanceofatleast50cm(19.7in.)fromthetopoftheprinterisrequiredforliftingtheprinterontoa

forklift.Theliftingheightoftheprinterisatleast20cm(7.8inches).

Theinstallationlocationmustbeaccessiblefromtheunloadingarea.Aprofessionalmoveris

responsibleforunloadingtheprinterfromthetruckandtransferringittotheinstallationlocation.

Theforkliftextensionsandtheprinter'scenterofgravityareshowninthefiguresbelow.

Warning: Lifting Hazard

Donotlifttheprinterfromthesides.Donotlifttheprinterfromthefront.The

printer'scenterofgravityisnearthebackoftheprinter.

Theforkliftextensionsandtheprinter'scenterofgravityareshowninthefiguresbelow.

Figure2Forkliftposition

Objet1000 Plus Shipment and Delivery

Figure3Printercenterofgravity

Objet1000 Plus Shipment and Delivery

InstallationArea

Theinstallationareashouldbefreeofsourcesofvibrationandelectromagneticinterferencethatcould

affecttheproperfunctioningoftheprinter.

Thefloorgradientshouldbelessthan0.5%(5mmpermeter).

Thefloorshouldbestableandabletobeartheloadoftheprinter.

Theareaaroundtheprintershouldremaindryatalltimes.

Shelvesandcabinetsarerecommendedneartheprinterforconvenientstorageoftools,parts,

accessories,manuals,andmaterials.

FloorPlan(PrinterArea)

Thefollowingisasamplefloorplan,showingthe3Dprintingsystem.Thedimensionsshowninthe

figurearetheminimumclearancerequirements.

Figure4Printerfloorplan(sample,nottoscale)



Makesurethattheprinterisonthesamelevelastheareasurroundingit.

Iftheprinterispositionedaboveorbelowtheareasurroundingit,itmightnotbepossibletoattachthe

unloadingcart.

Objet1000 Plus Installation Area

Other manuals for Objet1000 Plus

Table of contents

Other Stratasys 3D Printer manuals

Stratasys

Stratasys Connex500 User manual

Stratasys

Stratasys Fortus 250mc User manual

Stratasys

Stratasys Fortus 360mc User manual

Stratasys

Stratasys Objet500 User manual

Stratasys

Stratasys Fortus 900mc Operating instructions

Stratasys

Stratasys J5 Series User manual

Stratasys

Stratasys Objet1000 Plus User manual

Stratasys

Stratasys FDM Vantage Series User manual

Stratasys

Stratasys K6 Series User manual

Stratasys

Stratasys H350 User manual

Stratasys

Stratasys J3 Series User manual

Stratasys

Stratasys J826 Operating instructions

Stratasys

Stratasys J850 User manual

Stratasys

Stratasys UV800 User manual

Stratasys

Stratasys J850 User manual

Stratasys

Stratasys Objet500 User manual

Stratasys

Stratasys ProBleacher User manual

Stratasys

Stratasys Objet350 User manual

Stratasys

Stratasys RK1600 WJ User manual

Stratasys

Stratasys F123 Series User manual

Stratasys

Stratasys Fortus 900mc User manual

Stratasys

Stratasys Dimension BST 1200 User manual

Stratasys

Stratasys F770 Operating instructions

Stratasys

Stratasys Origin One User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

MakerBot

MakerBot Replicator user manual

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide

LONGER

LONGER LK4 Pro quick start guide

German RepRap

German RepRap X400 Pro V3 user guide