Steren SWI-008 User manual
ENGLISH
ENGLISH-02
IMPORTANT
Before using your new Fast Ethernet switch, please read the
following recommendations.
Do not try to open the equipment, may cause malfunction.
Warranty is void if you open the case.
Do not expose the device to extreme weather.
Do not use or store the equipment near wet places. May cause
malfunction or shock hazard.
Clean with a soft, dry cloth.
FEATURES
Complies with IEEE802.3, IEEE802.3u standards.
Data transfer up to 100Mbps.
RJ45 ports with auto negotiation.
Supports Auto-MDI /MDIX.
Supports Full Duplex ow control.
Supports MAC address, auto learning and auto aging.
LEDs indicator for Power, Link and Activity.
•
•
•
•
•
•
•
•
•
•
•
•
ENGLISH
ENGLISH-03
CONTROLS
1.- Power LED.
Light on when the equipment plugs to an AC household outlet.
2.- Link / ACT LED.
Light on when the equipment is connected to a RJ45 port / ashes when
there’s reception or transmission of data.
3.- RJ45 connector.
Allows you to plug devices to switch.
4.- AC power adaptor.
Allows you to plug the AC power adaptor included in the package.
12
2
2
34
ENGLISH
ENGLISH-04
INSTALATION
Decide where you want to place the switch. Find a at horizontal
surface such as a table, desk or shelf. The switch comes with a
wall-mounting screws to place it vertically.
Make sure the selected location is:
- Not in direct sunlight
- Not near a heater or heating vent
- Not cluttered or crowded. There should be at least 2 inches
of clear space on all sides of the switch.
- Well ventilated
Also, you’ll need a Category 5 (Cat 5) Ethernet cable with RJ45
connectors for each device you want to connect into the switch. Each
Ethernet cable must be smaller than 328 feet.
1.- Place the switch on a at surface or hook onto the screws.
2.- For each device, insert one end of an Ethernet cable into the port in
the device and insert the other end into one of the Ethernet ports on the
switch.
3.- Connect the power’s adapter cord into the switch and then plug the
adapter into an AC household outlet. The Power light should light up.
The corresponding port number for each connected and powered
device should light and ash when activity occurs.
ENGLISH
ENGLISH-05
If you have more than 5 devices which want to connect to the
switch, you must do it through a hub or another switch.
If any light doesn’t operate as we indicated, refers to
Troubleshooting section.
Ethernet cable is not included in the package.
This kit is ideal for electronic students or hobbyists because
it allows them to develop creativity in the programming of
ENGLISH
ENGLISH-06
TROUBLESHOOTING
TROUBLE SOLUTION
The power light does not lit.
The port number light does
not lit for a connected device.
Make sure the power cord
is properly connected to the
switch.
Make sure you are using the
supplied power adapter.
Make sure the cable
connectors are securely
plugged to the switch.
Make sure the connected
device is turned on.
Make sure the cable is
smaller than 328 feet.
SPECIFICATIONS
Input: 7.5V - - - 1000mA
Standars: IEEE802.3 10Base-T, IEEE802.3u, 100Base-TX
Topology: Star
Protocol: CSMA/CD
date rate: Ethernet: 10Mbps (Half Duplex), 20Mbps
(Full Duplex), Fast Ethernet: 100Mbps
(Half Duplex), 200Mbps (Full Duplex)
Network interface: 10Base-T: UTP cable Cat 3, 4, 5 (up to
100 metres), EIA/TIA-568 100ohms
STP(up to 100 metres) 100Base-T:
UTP cable Cat 5, 5e (up to 100 metres),
EIA/TIA-568 100ohms STP (up to
100 metres).
Transfer method: Store-and Forward.
MAC adress learning: Automátic leraning/update
Frame lter rate: 10Base-T: 14880pps/port
100Base-Tx: 148800pps/port
Operating temperature: 0 - 40°C
Storage temperature: -40 - 70°C
Operating humidity: 10% - 90% noncondensed
Storage humidity: 5% - 95% non-condensed
POWER ADAPTOR
Input: 110V~ 60Hz 0,15A Output: 7.5V - - - 1000mA
Product design and specications subject to change without
previous notice.
ENGLISH
ENGLISH-07
WARRANTY
This Steren product is warranted under normal usage against defects in workmanship and
materials to the original purchaser for one year from the date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase ticket, product
box or package, and product, must be presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accessories to customer, as well as
warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries,
failure to follow enclosed instructions, improper repair by unauthorized personnel, improper
safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
Product: 8 Port fast Ethernet switch
Part number: SWI-008
Brand: Steren
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your nearest dealer. If
you are in Mexico, please give a call to our Call Center.
Call Center
01 800 500 9000
Other manuals for SWI-008
1
Table of contents
Languages:
Other Steren Switch manuals
Steren
Steren FASTHOME 550-030 User manual
Steren
Steren SWI-50 User manual
Steren
Steren EXT16-4B User manual
Steren
Steren 201-737 User manual
Steren
Steren SHOME-110 User manual
Steren
Steren SWI-600 User manual
Steren
Steren COM-320 User manual
Steren
Steren ELE-106 User manual
Steren
Steren SHOME-140 User manual
Steren
Steren COM-315 User manual
Steren
Steren COM-445 User manual
Steren
Steren COM-365 User manual
Steren
Steren USB-527 User manual
Steren
Steren SWI-005 User manual
Steren
Steren USB-524 User manual
Steren
Steren USB-523 User manual
Steren
Steren SWI-005 User manual
Steren
Steren EL-101 User manual
Steren
Steren 200-385 User manual
Steren
Steren USB-520 User manual
