Stealth Products i2i Guide
USER MANUAL
Positioning & Support
i2i Head & Neck Positioning System
Stealth’s User Manual and Maintenance Guide for
the i2i Head & Neck Positioning System
i
Customer Satisfaction 1.0
Stealth Products strives for 100% customer satisfaction. Your complete
satisfaction is important. Please contact us with feedback or suggested changes
that will help improve the quality and usability of our products.
You may reach us at:
General
Read and understand all instructions prior to the use of the product. Failure to
adhere to instructions and warnings in this document may result in property
damage, injury, or death. Product misuse due to failure of the following
instructions will void the warranty.
Immediately discontinue use if any function is compromised, parts are missing,
loose, or shows signs of excessive wear. Consult with your supplier for repair,
adjustment, or replacement.
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
Stealth Products, LLC
104 John Kelly Drive, Burnet, TX 78611
Phone: (512) 715-9995 Toll Free: 1(800) 965-9229
Fax: (512) 715-9954 Toll Free: 1(800) 806-1225
ii
Important Information 2.0
Important Information!
All persons responsible for fitting, adjustment, and daily use of the devices
discussed in these instructions must be familiar with and understand all safety
aspects of the devices mentioned. In order for our products to be used
successfully, you must:
Read and understand all instrucons and warnings.
Maintain our products according to our instrucons on care and maintenance.
Devices should be installed and adjusted by a trained technician.
Supplier Reference
Supplier:
Telephone:
Address:
Purchase Date:
Model:
iii
Introduction 3.0
Before you install or begin using this product, it is important that you read and
understand the content of these installation and operating instructions. The
installation instructions will guide you through the possibilities with the
i2i Positioning System.
Instructions are written with the expressed intent of use with standard
configurations. They also contain important safety and maintenance
information. For further assistance, or more advanced applications, please
contact your supplier or Stealth Products at (512) 715-9995 or toll free at
1-800-965-9229.
Always keep the operating instructions in a safe place so they may be
referenced as necessary.
All information, pictures, illustrations, and specifications are based on the
product information that was available at the time of printing. Pictures and
illustrations shown in these instructions are representative examples and are
not intended to be exact depictions of the various parts of the product.
Ordering Documentation
You can download additional copies of this User Manual on the Stealth website:
https://stlpro.site/stealth-docs
and search: i2i User Manual in the search bar at the top of the page.
iv
Warranty 4.0
Our products are designed, manufactured, and produced to the highest of
standards. If any defect in material or workmanship is found, Stealth Products
will repair or replace the product at our discretion. Any implied warranty,
including the implied warranties of merchantability and fitness for a particular
purpose, shall not extend beyond the duration of this warranty. Stealth
Products, LLC does not warrant damage due to, but not limited to:
Misuse, abuse, or misapplicaon of products.
Modicaon or product without wrien approval from Stealth Products, LLC.
Any alteraon or lack of serial number, where applicable, will automacally
void this warranty.
Stealth Products, LLC is liable for replacement parts only.
Stealth Products, LLC is not liable for any incurred labor costs.
No person is authorized to alter, extend, or waive the warranties of Stealth
Products, LLC.
Stealth Products warrants against failure due to defective materials
or workmanship:
Covers: 2 years
Hardware: 5 years
Electronics: 3 years
In Case of Product Failure
In the event of product failure covered by our warranty, please follow the
procedures outlined below:
1. Call Stealth at +1 (512) 715-9995 or toll free +1-800-965-9229.
2. Request the Returns Department or obtain an RA from the Returns Department and
follow department or documentaon instrucons.
v
Table of Contents 5.0
1.0 Customer Satisfaction............................................................................. i
2.0 Important Information .......................................................................... ii
3.0 Introduction ........................................................................................... iii
4.0 Warranty ................................................................................................. iv
5.0 Table of Contents ................................................................................... v
6.0 Warning Labels ..................................................................................... vii
6.1 Warning Labels .................................................................................................... vii
6.2 Limited Liability.................................................................................................... vii
6.3 Testing..................................................................................................................... vii
7.0 Hardware Positioning ............................................................................ 1
7.1 Available Sizes........................................................................................................ 1
8.0 Part Numbers .......................................................................................... 2
9.0 Design and Function .............................................................................. 3
9.1 Chin Prompt............................................................................................................ 3
9.2 Proper Use ............................................................................................................... 3
9.3 Fitting......................................................................................................................... 4
10.0 i2i Head Positioning............................................................................. 5
10.1 Indications for Use ............................................................................................. 5
10.2 Recommendation & Fitting............................................................................ 5
10.3 Installing the Seat Back Mount ..................................................................... 6
vi
Table of Contents 5.0
11.0 Mounting & Adjusting ........................................................................ 7
11.1 Mounting Head Positioning to Hardware................................................ 7
11.2 Link Hardware ..................................................................................................... 7
11.3 Flip Down Hardware ......................................................................................... 8
11.4 Offset Link Hardware........................................................................................ 8
12.0 First Time Use ....................................................................................... 9
12.1 Dealer Assistance............................................................................................... 9
12.2 User Testing ......................................................................................................... 9
12.3 Conditions of Use .............................................................................................. 9
13.0 Maintenance ....................................................................................... 10
13.1 Cleaning............................................................................................................... 10
vii
Warning Labels 6.0
Warning Labels 6.1
Warnings are included for the safety of the user, client, operator and property.
Please read and understand what the signal words SAFETY, NOTICE, CAUTION,
WARNING and DANGER mean, how they could affect the user, those around
the user, and property.
Limited Liability 6.2
Stealth Products, LLC accepts no liability for personal injury or damage to
property that may arise from the failure of the user or other persons to follow
the recommendations, warnings, and instructions in this manual.
Testing 6.3
Initial setup and driving should be done in an open area free of obstacles until
the user is fully capable of driving safely.
Ensure that the client is properly aligned and that every alteration of the
physical installation or adjustment of the positioning system is complete.
NOTICE
Identifies important information not related to injury, but
possible property damage.
SAFETY
Indicates steps or instructions for safe practices, reminders of
safe procedures, or important safety equipment that may be
necessary.
CA UTION Identifies a potential situation which (if not avoided) will
result in minor to moderate injury,and property damage.
WA RNING Identifies a potential situation which (if not avoided) will
result in severe injury, death,and property damage.
DANG ER Identifies an imminent situation which (if not avoided) will
result in severe injury, death,and property damage.
1
Hardware Positioning 7.0
The standard i2i configuration uses TWB480 Flip Down Hardware, consisting of:
Vercal round stem with an-rotaon notch and ip down mechanism
Triangle clamp– needs to be posioned so it is even with the top of the seat back. When
the i2i is ipped down, the hardware will clear the top of the back, prevenng a potenal
safety hazard.
Posioning links with a mounng ball
Featured items:
i2i Head Posioning System– Head & Neck Posioning System
Chin Prompt– Padded Chin Support
TWB480 Hardware– Dual Link System with Quick Release System
FDM380– Incorporated with the TWB480, allowing the enre system to ip back
SBM400-Seat Back Mount
NO TI CE
If a client is shunted, consult their physician if you feel there may be any compression or
interference with the shunt before using the i2i.
Measurements Pediatric Small Medium Large Extra Large
Max. Neck Circumference 9in. 11in. 14in. 16in. 18in.
Max. Neck Width 3.5in. 4in. 4.5in. 5in. 5.75in.
Profile Height:
Standard
Low
2.25in.
4in
2.25in.
4.75in.
2.25in.
5.25in.
2.25in.
6in.
2.25in.
Arm Length
Standard
Short
4.5in.
6.5in.
4.5in.
7.5in.
5.5in.
8in.
6in.
9in.
6.25in.
Available Sizes 7.1
The i2i is available in Pediatric, Small, Medium, Large, and Extra Large sizes.
See the chart below for size information:
2
Part Numbers 8.0
Pediatric Small Medium Large Extra Large
i2i280 i2i480 i2i580 i2i680 i2i780
i2i282 i2i482 i2i582 i2i382 i2i782
i2i380 i2i430 i2i530 i2i630 i2i781
i2i382 i2i432 i2i532 i2i632 i2i783
i2i481 i2i581 i2i681 i2i790
i2i483 i2i583 i2i683 i2i792
i2i490 i2i590 i2i690 i2i740
i2i492 i2i592 i2i692 i2i742
i2i440 i2i540 i2i640 i2i791
i2i442 i2i542 i2i642 i2i793
i2i491 i2i591 i2i691
i2i493 i2i593 i2i693
Other manuals for i2i
2
Table of contents
Other Stealth Products Medical Equipment manuals
Stealth Products
Stealth Products MTMD-42 User manual
Stealth Products
Stealth Products SUS9 Swing Away Series User manual
Stealth Products
Stealth Products i2i User manual
Stealth Products
Stealth Products HMO500 User manual
Stealth Products
Stealth Products IDCH User manual
Stealth Products
Stealth Products i2i User manual
Stealth Products
Stealth Products Diego User manual
