StarTech.com IES81GW Guide

Manual Revision: 01/19/2017

For the latest information, technical specications, and support for

this product, please visit www.StarTech.com/IES81GW.

FR: Guide de l’utilisateur - fr.startech.com

DE: Bedienungsanleitung - de.startech.com

ES: Guía del usuario - es.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

IT: Guida per l’uso - it.startech.com

IES81GW

8-Port Gigabit Ethernet Switch

- Managed

*actual product may vary from photos

Quick-start guide

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (A)/NMB-3(A)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Quick-start guide

Table of Contents

Introduction............................................................................................1

Product diagram........................................................................................................................................ 1

Package contents...................................................................................................................................... 2

Requirements ............................................................................................................................................. 2

About the LED indicators......................................................................3

Wire the power inputs...........................................................................3

Reboot the network switch ..................................................................4

Reset to the default factory settings ..................................................4

Installation ..............................................................................................5

Install the enclosure on a wall.............................................................................................................. 5

Install the enclosure on a magnetic surface.................................................................................... 6

Mount the enclosure to a DIN rail....................................................................................................... 7

Technical support...................................................................................8

Warranty information............................................................................8

Quick-start guide

Introduction

Product diagram

Mounting hole

Link and activity

LED indicators

(2 per port)

Power LED

indicator

3-pin terminal

block

DC power input

RJ45 ports 1 to 4

RJ45 ports 5 to 8 Reset button

(not pictured)

Quick-start guide

Package contents

• 1 x network switch

• 1 x universal power adapter (NA/JP, UK, EU, ANZ)

• 1 x terminal block connector

• 4 x screw anchors

• 4 x screws

• 4 x attaching pins

• 4 x locking pins

• 4 x washers

• 4 x magnets

• 1 x DIN rail

• 3 x DIN-rail screws

• 8 x dust caps

• 1 x quick-start guide

Requirements

• Ethernet port connection

• RJ45 network cables

Requirements are subject to change. For the latest requirements, please visit

www.StarTech.com/IES81GW.

Quick-start guide

About the LED indicators

This network switch features a link and activity LED indicator for each of the eight

RJ45 ports. There is an additional power LED located above the 3-pin terminal block.

For more information about what the LED indicators signify, see the table below.

LED Behavior Signicance

LED indicator on the left

side of the RJ45 ports

Illuminated yellow Link was successfully

established

Blinking yellow Data is being transferred

at 10/100 Mbps

LED indicator on the right

side of the RJ45 ports

Illuminated green Link was successfully

established

Blinking green Data is being transferred

at 1000 Mbps

Power LED Illuminated Switch is receiving power

Wire the power inputs

You can use either the universal power adapter or the terminal block to power the

network switch. Alternatively, you can connect both the universal power adapter and

the terminal block to create a redundant power input.

You should use wire ranging in size of 12 to 24 AWG.

Caution! Make sure that you ground the enclosure before you install the terminal

block connector into the network switch.

1. Insert the grounding wire into the Ground port on the terminal block, and tighten

the wire clamp screws.

2. Insert the positive DC power wire into the V+ port on the terminal block connector,

and tighten the wire clamp screws.

3. Insert the negative DC power wire into the V- port on the terminal block connector,

and tighten the wire clamp screws.

4. Insert the terminal block connector into the 3-pin terminal block on the network

switch.

Quick-start guide

Reboot the network switch

The Reset button on the network switch is designed to reboot the network switch

without turning o and turning on the power.

• To reboot the network switch, press the Reset button.

Reset to the default factory settings

You can use the Reset button to reset the network switch to the following default

factory settings:

Default user name: admin

Default password: admin

Default IP address: 192.168.0.100

Subnet mask: 255.255.255.0

Default gateway: 192.168.0.254

• To reset to the default factory settings, press and hold the Reset button for more

than 5 seconds.

When you press the Reset button, the port LED indicators illuminate. When the LEDs

are no longer illuminated, the reset sequence is complete.

Quick-start guide

Installation

Install the enclosure on a wall

1. Hold the enclosure against the wall in the area that you want to install it, and use a

pencil to trace the location of the four mounting holes onto the wall.

2. Use the mounting holes that you traced on the wall as a template and drill holes in

the wall.

3. Insert the four screw anchors into the holes.

Note: Make sure that the screw anchors are ush against the wall.

4. Place the enclosure against the wall and insert the four screws through the

mounting holes on the enclosure and into the screw anchors. (gure 1)

5. Tighten the screws.

6. To power the switch, connect an external power adapter, wire the power inputs, or

do both.

7. Connect the RJ45 cables to the RJ45 ports on the enclosure.

Screw

Screw anchor

Mounting hole

gure 1

Quick-start guide

Install the enclosure on a magnetic surface

1. Push each of the attaching pins into a locking pin.

2. Insert the attaching and locking pins into one of the mounting holes on the

enclosure, through a washer, and into a magnet.

Note: To prevent the magnets from becoming loose, make sure that you position the

magnet so that the at side is against the enclosure.

3. Repeat step 2 for all of the mounting holes on the enclosure. (gure 2)

4. Attach the enclosure to a magnetic surface.

5. To power the switch, connect an external power adapter, wire the power inputs, or

do both.

6. Connect the RJ45 cables to the RJ45 ports on the enclosure.

Attaching pin

Locking pin

Washer

Magnet

gure 2

Quick-start guide

Mount the enclosure to a DIN rail

1. With the at side of the DIN rail positioned against the enclosure, line up the holes

on the DIN rail with the holes on the enclosure.

2. Insert the DIN-rail screws through the DIN rail and into the enclosure. (gure 3)

3. Tighten the screws.

gure 3

DIN-rail screw

DIN rail

4. Hook the DIN rail onto the top of the track, and push it against the track. (gure 4)

5. To power the switch, connect an external power adapter, wire the power inputs, or

do both.

6. Connect the RJ45 cables to the RJ45 ports on the enclosure.

gure 4

Table of contents

Other StarTech.com Switch manuals

StarTech.com

StarTech.com SV1107IPEXT User manual

StarTech.com

StarTech.com IES101GP2SFW User manual

StarTech.com

StarTech.com StarView SV431USB User manual

StarTech.com

StarTech.com SV221MICRO User manual

StarTech.com

StarTech.com SV201 User manual

StarTech.com

StarTech.com SV231QDVIUA User manual

StarTech.com

StarTech.com VS415RVGA User manual

StarTech.com

StarTech.com ST4100USBBL User manual

StarTech.com

StarTech.com SV431DD2DUA User manual

StarTech.com

StarTech.com DS15H54 System manual

StarTech.com

StarTech.com SV231DPU34K User manual

StarTech.com

StarTech.com ST3504USB User manual

StarTech.com

StarTech.com 5G4AIBS-USB-HUB-EU User manual

StarTech.com

StarTech.com SV231MDPU2 User manual

StarTech.com

StarTech.com SV431USBAE User manual

StarTech.com

StarTech.com SV431DI Manual

StarTech.com

StarTech.com ST7300USBM User manual

StarTech.com

StarTech.com SV211KUSB User manual

StarTech.com

StarTech.com SV231DPU34K User manual

StarTech.com

StarTech.com C2-DH46-UA2-CBL-KVM User manual

StarTech.com

StarTech.com SV211KT Manual

StarTech.com

StarTech.com StarView SV231USBGB User manual

StarTech.com

StarTech.com MSTMDP123HD User manual

StarTech.com

StarTech.com SV231DPUA User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual