StarTech.com USB2004EXTGB User manual

USB Extender

4-Port USB 2.0 Extender over

Cat5 or Cat6

Instruction Manual

USB2004EXT

USB2004EXTGB

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the receiver•

is connected.

Consult the dealer or an experienced radio/TV technician for help.•

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company

in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Table of Contents

Introduction..................................................................... 1

Packaging Contents.....................................................................1

System Requirements .................................................................1

Local Unit.....................................................................................2

Remote Unit.................................................................................3

Installation....................................................................... 4

Hardware Installation...................................................................4

Driver Installation.........................................................................5

Wiring Diagram ............................................................... 6

Speciﬁcations.................................................................. 7

Technical Support........................................................... 8

Warranty Information...................................................... 8

Introduction

The StarTech.com USB 2.0 extender over Cat5 or Cat6 offers a

simple USB extension, allowing you to place four USB 2.0 devices

up to 100m/330ft away from the computer, which is more than 20

times longer than the normal USB cable length restrictions. The USB

extender is comprised of both the Local and Remote units, which

can be connected together using standard UTP Cat5, Cat5e, or Cat6

Ethernet cabling. Supporting full Hi-Speed USB 2.0 data transfer

speeds up to 480Mbps, the extender is also backward compatible with

USB 1.0/1.1 (1.1Mbps/12Mbps respectively).

Packaging Contents

1 x USB 2.0 Extender Local Unit•

1 x USB 2.0 Extender Remote Unit•

1 x Power Adapter•

1 x Instruction Manual•

System Requirements

USB enabled computer system with available port•

USB compliant operating system•

Available power outlet at remote location•

Local Unit

RJ45 connector

RJ45

Link LED

RJ45

Activity LED

Power

LED

Host

LED

USB connector

(Host)

LED Description

Power Turns on when power is being supplied via the

USB port.

Host Turns on when the host computer system

detects the extender.

RJ45 Link Indicates connectivity between the Local and

Remote unit.

RJ45 Activity Indicates data transmission between the Local

and Remote units.

Remote Unit

RJ45 connector

DC Power connector

RJ45

Link LED

RJ45

Activity LED

LED Description

Power Turns on when power is being supplied via the

external powr adapter.

Host Turns on when the host computer system

detects the extender.

RJ45 Link Indicates connectivity between the Local and

Remote unit.

RJ45 Activity Indicates data transmission between the Local

and Remote units.

USB Port Indicates a USB peripheral device is connected

and detected on the host computer system.

USB Hub

Connector

Power

LED

Host LED

USB port

LEDs

The Local Unit can be connected to the host computer system either1.

when it is powered on or off.

Connect the Local Unit directly to a USB port on the host computer2.

system via the integrated USB cable. The Power LED should light

up if/when the host computer is powered on.

Connect the UTP (CAT5e, CAT6, etc.) network cable to the RJ453.

connector on the Local Unit.

NOTE: Ensure that the total length of cable between the Local and

Remote units is 100m or less. The cabling must also not go through

any networking equipment (e.g. router/switch/hub/etc.).

Setup the Remote Unit near the remote USB peripheral(s).4.

Connect the other end of the UTP cable from the Local Unit to the5.

RJ45 connector on the Remote Unit.

Connect the power adapter to the Remote Unit. The Power LED6.

should light up. The Host LED should start ﬂashing if the Local Unit

is powered. The host computer system should detect a USB hub

as being connected, and the Host LED on both units should light up

steady.

Plug the remote USB peripheral(s) into the USB Hub connector(s)7.

on the Remote Unit. The corresponding USB port LED should light

up. The USB device(s) should be detected as if connected directly

to the host computer system.

Install the drivers for the connected USB peripheral(s) as necessary.8.

Installation

Hardware Installation

Driver Installation

The USB Extender itself does not require a driver installation for

any operating system that supports USB. The USB Extender is a

pass-through hub, so is only seen as a standard Generic USB hub.

Drivers will still be required for any USB peripherals connected to the

extenders.

NOTE: A additional level of USB hubs can be used on the USB

extender (one hub per port), to provide additional USB ports. An

externally powered USB hub is recommended.

Wiring Diagram

The USB Extender uses all four pairs of wires in the UTP cable, so

either T568A or T568B termination can be used. Both ends of the

cable must use the same termination.

T568A Termination

Pin Wire Color Pair

1 White/Green 3

2 Green 3

3 White/Orange 2

4 Blue 1

5 White/Blue 1

6 Orange 2

7 White/Brown 4

8 Brown 4

T568B Termination

Pin Wire Color Pair

1 White/Orange 2

2 Orange 2

3 White/Green 3

4 Blue 1

5 White/Blue 1

6 Green 3

7 White/Brown 4

8 Brown 4

Specications

USB2004EXT

USB2004EXTGB

Bus Interface USB 2.0

Connectors

(Local Unit)

1 x RJ45

1 x USB type A male

Connectors

(Remote Unit)

1 x RJ45

4 x USB type A

LEDs (Local Unit) 1 x Power

1 x Host

LEDs (Remote Unit)

1 x Power

1 x Host

4 x USB Detect

Maximum Data Transfer Rate USB 2.0: 480Mbps

Maximum Cable Distance 100m / 330ft

USB Power (per port) Remote Unit: 500mA

Integrated Cable Length Local Unit: 6”

Power Adapter 5VDC, 3A

Operating Temperature 0°C ~ 50°C (32°F ~ 122°F)

Storage Temperature -5°C ~ 60°C (23°F ~ 140°F)

Humidity 0 ~ 80% RH

Dimensions (Local Unit) 44.0mm x 87.0mm x 24.0mm

Dimensions (Remote Unit) 110.0mm x 69.0mm x 28.0mm

Weight Local Unit: 60g

Remote Unit: 200g

This manual suits for next models

Table of contents

Other StarTech.com Extender manuals

StarTech.com

StarTech.com ST1218T User manual

StarTech.com

StarTech.com USBthere USB110EXT User manual

StarTech.com

StarTech.com ST121WHDS User manual

StarTech.com

StarTech.com ST121WHD2 User manual

StarTech.com

StarTech.com SV565FXDUSA User manual

StarTech.com

StarTech.com SV565UTPUL User manual

StarTech.com

StarTech.com ST12MHDLNV User manual

StarTech.com

StarTech.com ST121HDBT20L User manual

StarTech.com

StarTech.com STUTPRXL User manual

StarTech.com

StarTech.com STUTPRXWLA User manual

StarTech.com

StarTech.com ST121HDBTPW User manual

StarTech.com

StarTech.com USB110EXT2 User manual

StarTech.com

StarTech.com ST12MHDDC User manual

StarTech.com

StarTech.com ST121UTPMINI User manual

StarTech.com

StarTech.com EOC1110R User manual

StarTech.com

StarTech.com ST121HD20FXA2 User manual

StarTech.com

StarTech.com SVIDUTPEXTA User manual

StarTech.com

StarTech.com 4K70IC-EXTEND-HDMI User manual

StarTech.com

StarTech.com ST121HDBT20L User manual

StarTech.com

StarTech.com SV565UTPDUA User manual

StarTech.com

StarTech.com USBthere USB221EXT User manual

StarTech.com

StarTech.com ST12MHDLAN User manual

StarTech.com

StarTech.com ST122UTPAGB User manual

StarTech.com

StarTech.com ST121HDBTE User manual

Popular Extender manuals by other brands

SY HDBT-60T installation guide

Appsys ProAudio

Appsys ProAudio ADX-16 user manual

Atlona

Atlona RS232 user manual

IDK

IDK OPF-TH1000-A user guide

Enable-IT

Enable-IT 824WP quick start guide

Worx

Worx Landroid RadioLink WA0864 Get started

TP-Link

TP-Link TL-WA730RE user guide

Camplex

Camplex CMX-HDMI-SFPL user manual

SC&T

SC&T HE03-4K user manual

Marmitek

Marmitek MegaView70 user manual

Samsung

Samsung SCS-26UC4 user guide

Foxun

Foxun SX-GES24 operating instructions

MuxLab

MuxLab 500771 Operation manual

foxunhd

foxunhd SX-AEX01 operating instructions

TERK Technologies

TERK Technologies LFIRX2 owner's manual

Devolo

Devolo Audio Extender supplementary guide

Edimax

Edimax EW-7438RPn V2 instructions

Shinybow USA

Shinybow USA SB-6335T5 instruction manual