StarTech.com 410VDSLEXT User manual
VDSL Ethernet LAN Extender
4-Port 10/100Mbps VDSL2
Ethernet Extender Kit
over Single Pair Wire
410VDSLEXT
410VDSLEXTGB
410VDSLEXTEU
Instruction Manual
Manual Revision:11/29/2010
For the most up-to-date information, please visit www.startech.com
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
i
Table of Contents
Introduction..................................................................... 1
Packaging Contents..................................................................... 1
System Requirements ................................................................. 1
Front View.................................................................................... 2
Rear View .................................................................................... 2
Installation....................................................................... 3
Hardware Installation................................................................... 3
Driver Installation......................................................................... 3
Configuration .................................................................. 3
Web Interface .............................................................................. 3
Setup Wizard (CPE Modem only)............................................ 4
Advanced Menu....................................................................... 4
Specifications.................................................................. 10
Technical Support........................................................... 11
Warranty Information...................................................... 11
1
Introduction
The 410VDSLEXT 10/100 4 Port VDSL2 Ethernet Extender Kit over
Single Pair Wire lets you span a 10/100 network over long distances
(up to 1km) to multiple users or network segments while maintaining
high-speed network connectivity.
With the ability to run the connection over new or existing RJ45 cabling,
RJ11 phone lines, or any other type of single pair wire, the 4 port
VDSL2 kit provides a simple to install, ready out-of-the-box solution
that includes both the Ethernet-VDSL2 extender and receiver units.
Perfect for connecting isolated user stations within a building or
between separate buildings, or overcoming infrastructure obstacles
(e.g. older stone/concrete architecture) where new wiring or wireless
may be impossible. This LAN extender kit helps to eliminate expense
by allowing video streaming and data to share the same telephone pair
without interference.
Packaging Contents
• 2 x VDSL2 Extender Unit (CO/CPE Modem)
• 1 x RJ11 cable
• 1 x RJ45 cable
• 2 x Power Adapter
• 1 x Software CD
System Requirements
• 10/100 Mbps Ethernet network
• Available AC electrical outlets
2
Rear View
Front View
3
Installation
Hardware Installation
1. Place each VDSL Extender unit at their respective end-point
locations. Make sure an AC electrical outlet is located nearby.
2. Connect the included power adapters to the pair of VDSL Extender
units. The Power LED should light up solid.
3. Connect the “Line” RJ11 connector on the VDSL Extender units
either directly together with patch cabling, or to a buildings existing
analog telephone wiring. If the two units are able to successfully
communicate with each other, the “WAN” LED should light up solid.
OPTIONAL: If the telephone wiring is also used for POTS telephone
service, then a telephone may be connected to the “Phone” RJ11
connector on the VDSL Extender units.
4. Connect each computer, or Ethernet networking device to an
available RJ45 connector on the VDSL Extender units. The
respective LAN LED should light up to indicate a successful physical
connection.
Driver Installation
No driver or software installation is required.
Conguration
Web Interface
Each of the VDSL Extender units have a built-in web interface, for
configuring the router settings (WAN and LAN ports), if necessary.
The interface can be access via their IP addresses (CO Modem:
192.168.16.249, CPE Modem: 192.168.16.250). The default password
is: admin
The main menu screen on the CPE Modem has two options: “Setup
Wizard” for quick setup, and “Advanced Setup” for a more customized
configuration. The CO Modem only has “Advanced Setup” options.
4
Setup Wizard (CPE Modem only)
The Setup Wizard allows for quick and easy configuration of the most
common settings (WAN) for the VDSL Extender.
Advanced Menu
System
This section allows for general configuration/administration of the VDSL
Extender unit.
5
6
WAN
This section can configure how the built-in VDSL Modem connects to a
DSL Internet Service Provider (ISP) through the “Line” RJ11 connector.
The modem supports Dynamic IP, Static IP and PPPoE modes.
LAN
The LAN section is used to configure the IP address and DHCP server
on the RJ45 Ethernet side of the VDSL Extender unit. By default the
DHCP server is not enabled.
7
NAT
This section is used to configure the advanced features on the
Ethernet side of the VDSL Extender unit. This include “Virtual Server”,
“Port Mapping” and DMZ settings.
Other manuals for 410VDSLEXT
1
This manual suits for next models
2
Table of contents
Other StarTech.com Extender manuals
StarTech.com
StarTech.com IREXT2 System manual
StarTech.com
StarTech.com USB2004EXTV User manual
StarTech.com
StarTech.com ST121SHD30 User manual
StarTech.com
StarTech.com ST121UTPEP User manual
StarTech.com
StarTech.com ST121HD20L User manual
StarTech.com
StarTech.com ST12MHDLAN4K User manual
StarTech.com
StarTech.com STDHVHDBT User manual
StarTech.com
StarTech.com ST12MHDLNHR User manual
StarTech.com
StarTech.com SV565UTPU User manual
StarTech.com
StarTech.com IPUSB2HD2 User manual
StarTech.com
StarTech.com ST122UTPA User manual
StarTech.com
StarTech.com HDBOOST4K User manual
StarTech.com
StarTech.com SVIDUTPEXTA User manual
StarTech.com
StarTech.com SV565LANDUA User manual
StarTech.com
StarTech.com ST121USBHD User manual
StarTech.com
StarTech.com ST121SHD50 User manual
StarTech.com
StarTech.com SV565HDIP User manual
StarTech.com
StarTech.com USBthere USB110EXT User manual
StarTech.com
StarTech.com ST121UTP User manual
StarTech.com
StarTech.com ST121HD20FXA User manual
