StarTech.com InfoSafe UNI3510U2EB User manual

Manual Revision: 03/28/2012

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

UNI3510U2EB

UNI3510UEBEU

UNI3510UEBGB

3.5 eSATA USB 2.0 to IDE SATA External

Hard Drive Enclosure

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use ofTrademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Hardware Guide .....................................................................................2

Front Panel................................................................................................................................................... 2

Rear Panel .................................................................................................................................................... 2

Installation ..............................................................................................3

Hardware Installation .............................................................................................................................. 3

Driver Installation...................................................................................................................................... 4

Software Installation................................................................................................................................ 4

Recognizing the Hard Drive .................................................................6

Windows XP ................................................................................................................................................ 6

Windows Vista ............................................................................................................................................ 7

Specications..........................................................................................8

Technical Support ..................................................................................9

Warranty Information............................................................................9

Instruction Manual

Introduction

This enclosure lets you turn almost any high capacity 3.5” Serial ATA (SATA) or IDE hard

drive into an eSATA (SATA only) or USB (SATA or IDE) external hard drive, allowing you

to customize your external storage solution based on your preference of hard drive

model and manufacturer.

Packaging Contents

• Hard Drive Enclosure

• USB Mini B Cable

• eSATA Cable

• IDE Cable

• Driver CD

• Enclosure Stand

• Power Adapter

• SP4 to LP4 Adapter Cable

• SATA 7+15 pin cable

System Requirements

• Available USB 2.0 or eSATA port on computer system

• Microsoft® Windows® 2000/XP/Vista/Server 2008 R2/7 (32/64-bit)

• Apple® Mac OS® 9.x/10.x, or Linux® kernel 2.4.1.0 and above

Instruction Manual

Hardware Guide

Front Panel

Rear Panel

1. Power Button/LED

2. Backup Button

1. DC In Port

2. eSATA Port

3. Mini USB Port

4. Hard Drive Release Switch

Instruction Manual

Installation

Hardware Installation

1. Open the hard drive enclosure by pushing the rear panel release button to the right

and sliding the hard drive bracket out of the external casing from the front.

2. If using an IDE/ATA hard drive, ensure that the hard drive you are using is set to MASTER.

3. Pull the two tabs on either side of the hard drive holding mechanism up, then

connect the provided SATA or IDE data and power supply cables to the rear ports of

the drive.

4. SATA HDD: If you will be using the USB 2.0 interface to connect to the enclosure,

plug the SATA data cable into the port labelled CN5 on the enclosure’s PCB board.

If using the eSATA interface to connect to the enclosure, plug the SATA data cable

into the port labeled CN6 on the enclosure’s PCB board. The locations of the CN5

and CN6 ports are shown below. Plug the power connector into the J1 port on the

PCB board.

Instruction Manual

5. IDE HDD: Only the USB 2.0 interface is available for connecting an IDE hard drive to

the host computer. Plug the 40-pin IDE data cable into the port labelled CN1 on the

enclosure’s PCB board. Plug the included 4-pin SP4 to LP4 power adapter cable into

the J1 connector.

6. To mount the hard drive, place it into the holding tray and press the tabs on either

side down to secure the drive in the enclosure.

7. Slide the hard drive holding mechanism into the external casing, ensuring that the

release button on the rear panel returns to its original, locked position.

Driver Installation

Windows® 2000/XP/Vista/7, Mac OS® 9.x/10.x, Linux Kernel® 2.4.x +

No driver installation is required for these operating systems, as this enclosure is

natively supported, so the drivers are already installed.

CN5

CN6

J1 CN1

Instruction Manual

Software Installation

The following steps outline the procedure to install the software included with your

drive enclosure in Windows.

1. Insert the Drivers CD into your computer’s CD-ROM. Open the DRIVERS.exe

application to begin the installation process.

2. Once the installer is running, there are a number of options available to you from

the DRIVERS.exe home screen. To install the backup software, click Install Backup

Program under the heading that corresponds with your drive-type (IDE or SATA).

3. The PCClone EX Lite Installer window will appear. Click Install to proceed with the

installation process.

4. The License and Warranty Agreement will appear. To continue, click Agree.

Instruction Manual

1. Click Browse to designate the directory in which the software will be installed. Once

you have made your selection, click Install to continue.

2. The installation will now take place. Once the installation is complete, you may exit

the DRIVERS.exe application.

Recognizing the Hard Drive

Windows XP

USB 2.0

If you are using the USB 2.0 interface to connect the hard drive enclosure to your

computer, no setup is required. Simply plug the hard drive enclosure into an available

USB port and turn the power on to the hard drive enclosure. Open My Computer and

the drive should be visible under the heading “Devices with Removable Storage.”

Instruction Manual

eSATA

If you are using the eSATA interface to connect the hard drive enclosure to your

computer, there are two setup processes you can follow. If the hard drive enclosure

is powered on upon booting up the computer, it will automatically detect the drive.

Otherwise, if you connect and power on the hard drive enclosure once the computer

has already been booted up, you will need to open the Device Manager to scan for it.

The following directions outline the necessary steps to access your hard drive when

the computer has already been booted up:

1. Right click My Computer and click Manage.

2. In the left pane, select Device Manager.

3. In the Device Manager window, click the + next to the Disk Drives icon. Since your

drive was not powered on during the boot up process, it should not yet be visible.

4. Turn on the hard drive enclosure. Once the power indicator is illuminated, click the

Scan button.

5. The Device Manager will scan for plug and play hardware. Once it has completed

the scan, your drive should be visible below the Disk Drives heading.

Windows Vista/7

USB 2.0

If you are using the USB 2.0 interface to connect the hard drive enclosure to your

computer, no setup is required. Simply plug the hard drive enclosure into an available

USB port and turn the power on to the hard drive enclosure. Open My Computer and

the drive should be visible under the heading “Devices with Removable Storage.”

This manual suits for next models

Table of contents

Other StarTech.com Enclosure manuals

StarTech.com

StarTech.com S2510BU3PW User manual

StarTech.com

StarTech.com SAT2510U2REM User manual

StarTech.com

StarTech.com INFOSAFE IDE2510U2 User manual

StarTech.com

StarTech.com SAT2510BU2E User manual

StarTech.com

StarTech.com SAT35401U System manual

StarTech.com

StarTech.com RK1019SIDEM User manual

StarTech.com

StarTech.com S251BU31C3CB User manual

StarTech.com

StarTech.com SAT3540ER2 User manual

StarTech.com

StarTech.com DRW110ATA Manual

StarTech.com

StarTech.com MONSTADJD User manual

StarTech.com

StarTech.com RK1520WALHM User manual

StarTech.com

StarTech.com SAT2510U2F User manual

StarTech.com

StarTech.com S3510BMU33B User manual

StarTech.com

StarTech.com SAT2510BU3 User manual

StarTech.com

StarTech.com HSB13SATSASB User manual

StarTech.com

StarTech.com S252SMTB3 User manual

StarTech.com

StarTech.com UNI3510BMU32 User manual

StarTech.com

StarTech.com InfoSafe IDECASE25OTG User manual

StarTech.com

StarTech.com IDECASE18U2B User manual

StarTech.com

StarTech.com S3520WU33ER System manual

StarTech.com

StarTech.com InfoSafe SAT3510U2B User manual

StarTech.com

StarTech.com DRW150ATA Manual

StarTech.com

StarTech.com SAT2510U2F User manual

StarTech.com

StarTech.com SM21BMU31C3 User manual

Popular Enclosure manuals by other brands

SilentiumPC

SilentiumPC Armis AR5 Hardware installation

Pulsar

Pulsar 17/TRP80/DSPR Assembly instructions

Thermaltake

Thermaltake V150 TG user manual

MSI

MSI MPG SEKIRA 500X quick start guide

Antec

Antec Dark fleet DF-10 user manual

Nexans

Nexans WTC05 installation manual

Peavey

Peavey DS 1502 Specifications

D-Link

D-Link ShareCenter Pro DNS-1550-04 user manual

Rosewill

Rosewill RX82-U(JBOD) user manual

QNAP

QNAP SAS JBOD CLI 1.0 user guide

GAMDIAS

GAMDIAS Talos P1 Quick installation guide

Auvs

Auvs KR615 user manual

Digitus

Digitus DA-71114 manual

CommScope

CommScope FDH 3000 user manual

FS FHD-FWME4 quick start guide

JBL

JBL CS1215T owner's manual

Pulsar

Pulsar ARAD-S4 manual

Pulsar

Pulsar AWO454 Assembly instruction