SPYKER P60 Series User manual
1008192 Rev. A©2010 Spyker Spreaders/A Brinly-Hardy Co.
Model P60/S60 Series
Spyker Spreaders
Contact Us at 800.972.6130
This manual contains information for the safety
of persons and property. Read it carefully before
assembly and operation of the equipment!
IMPORTANT
Operator's Manual
1008192 Rev. A 2
1
19
13
20
18 62
22
31
6
6
6
28
18
28
18
28
18
28
60
25
10
3
27
5
6
38
2
18
6
29
47
35
39
6
4
7
27
24
30
32
30 17
21
9
5
23
15
44
34
18
25
62
62
62
Rate Gate and
Deflector Explosion
Hopper Explosion
Handle Explosion
1008192 Rev. A3
58
56
12
51
48
14
45
8
46
14
16
54
49
53
50
52
49
50
55
59
57
28
*As needed for shimming
28
6
26
3
37
9
36
11
3
61
41
6
6
4*
4*
3
3
26
41
61
42
41
42
43
33
40
Frame Explosion
Spinner/Axle Explosion
1008192 Rev. A 4
New Part Number Qty Description
1 1008067 1 Decal Spyker Square Blue
2 1007773 1 Lever, Control
3 05-90-0054 5 1/4-20 x 1-1/2" Hex
Bolt, SS
4 05-92-0008 6 1/4" Washer, SS
5 05-94-0051 2 Nylon Flange Bushing
6 SS-91-0004 18 1/4-20 Nylon Locknut,
SS
7 05-90-0121 1 1/4-20 x 3/4" Hex Bolt,
SS
8 1008078 1 Spinner Shaft
9 1008079 1 Linkage Assembly
10 1008082 1 Control Rod
11 1007794 2 Brace, Cross
12 1008085 1 Axle
13 1008104 1 Screen
14 SS-92-0002 2 Felt Washer
15 05-94-0078 1 Pine Tree Clip
16 SS-96-0003 1 Agitator Wire
17 05-94-0043 1 Accuway Diffuser
18 05-94-0064 6 Nylon Washer
19 1008169 1 Cover
20 1008192 1 Manual for push
spreader
21 05-44-2210 1 Accuway Screw Assembly
22 05-71-2205 1 Hopper Bottom Plate
23 SS-94-0006 1 Dial
24 05-24-1102 1 Rate Gate Link, Polished
25 05-80-0030-R 1 Hopper, Black Plastic
1 Hopper, SS
26 05-90-0017 2 1/4-20 x 2-3/4" Hex
Bolt, SS
27 05-90-0047 2 1/4-20 x 1" Hex Bolt, SS
28 05-90-0080 8 1/4-20 x 1-3/4" Hex
Bolt, SS
29 05-94-0022 2 Handle Grips
30 05-94-0042 2 Rate Gate/Accuway
Guide
31 99-10-0205 5 1/4-20 x 1/2" Hex Bolt,
SS
New Part Number Qty Description
32 05-94-0068 1 Rate Gate
33 05-90-0102 1 Hair Pin, Small SS
34 05-94-0069 1 Dial Mount
35 1008083-10 1 Dual Handle Painted
1008069-01 1 Dual Handle, SS
36 1008087-10 1 Axle Support Painted
1008072-01 1 Axle Support, SS
37 1008090-10 1 Hopper Support Painted
1008075-01 1 Hopper Support, SS
38 1007828 2 Handle Knob
39 SL-HP-1113-1 1 Rate Gate & Dial
Assembly
40 05-90-0065 1 3/16 x 1-3/4" Clevis Pin
41 05-92-0004 3 Flat Washer, SS
42 05-95-0016-JD 2 Wheel
43 05-90-0040 1 Rue Ring Locking Pin
44 SS-94-0007 1 Hopper Bottom Bearing
45 SS-90-0002 1 1/8 x 7/8" Roll Pin
46 SS-94-0012-1 1 Spinner
47 05-99-0063 1 On-off Decal
48 SS-90-0001 1 1/8 x 3/4" Roll Pin
49 05-90-0093 2 5/8" Gearbox Bushing
50 05-90-0094 2 3/8" Spinner Shaft
Bushing
51 05-90-0096 1 3/16 x 1" Dowel Pin, SS
52 05-94-0033 1 Bevel Gear
53 05-94-0034 1 Pinion Gear
54 05-288-1027 1 Nylon Pin Retainer
55 05-90-0097 8 #10-24 x 5/8" Flange
Head Bolt, SS
56 05-91-0008 8 #10-24 Nylon Locknut,
SS
57 05-94-0037 1 Gear Box Cover Front
58 05-94-0038 1 Gear Box Cover Rear
59 05-98-0111 1 Grease Zerk 1/4-28
60 05-93-0075 1 Spyker Accuway Label
61 F-283 2 Axle Bearing
62 SS-92-0002 4 Felt Washer (For
Stainless Hopper Only)
1008192 Rev. A5
1. Install Linkage to Lever as shown, Figure 1.
2. Turn Handle Assembly sideways and install Linkage
into Rate Gate Lever as shown, Figure 2.
3. Attach Handle Assembly to Frame using (4) 1/4 x
1-3/4" long Bolts and 1/4" Nylon Insert Locknuts,
Figure 3.
Figure 1
Figure 2
Figure 3
1008192 Rev. A 6
5. Install Handle Grips on Handles of Spreader, Figure
4.
Figure 4
1008192 Rev. A7
READ BEFORE USING
OPERATE SAFELY
Keep bystanders away when you operate this machine.
Use this machine for intended purpose only.
Do not let children or an untrained person operate
machine.
Keep all parts in good condition and properly installed.
Fix damaged parts immediately. Replace worn or broken
parts.
Do not modify the machine or safety devices.
Unauthorized modifications to the machine may impair
its function and safety, and void the warranty.
Do not let anyone sit or ride on equipment during
operation. Keep riders off attachment.
Wear substantial footwear and long trousers. Do not
operate the equipment when barefoot or wearing open
sandals.
Do not wear loose fitting clothing that can get caught in
moving parts.
Always wear eye protection when operating the
equipment.
Stay alert for holes in the terrain and other hidden
hazards.
Watch out for traffic when crossing or near roadways.
Before you operate any feature of this machine, observe
your surroundings and look for bystanders.
Always wash hands after contact with fertilizers and
pesticides.
Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition.
1008192 Rev. A 8
READ BEFORE USING
Become Familiar With The Operation Of The Spreader Before
You Put Material In The Hopper
• Practice walking with the spreader, opening and
closing the rate gate at the appropriate times.
• Travel at a constant speed and operate the spreader
lever position. Remember: Open the rate gate after
the spreader is in motion at operating speed (about
3 mph, or at a brisk walking pace).
• Close the rate gate while spreader is still at
operational speed.
Dial Setting Information
The RATE DIAL has 9 numbers with 10 stops between
each number. This allows for accurate control of the
spreading rate. The dial is set with only a turn, it will
automatically lock into the set position. LINE UP THE
DIAL NUMBER WITH THE DIAL INDICATOR.
Rate Dial
• The spread width ranges from 4 - 12 ft. wide
depending on the volume/density, particle size of the
material, and rate of travel.
• The spread thins or feathers at the outer edges,
eliminating sharp, "Edge Of Spread" lines which
cause stripes and streaks. Extra coverage can be
given under trees and other heavy feeding areas
without showing "Edge Of Spread" lines.
• Gaps and double overlaps are less likely. Small
errors in travel are forgiven and do not show.
WARNING: When spreading products containing
herbicides, exercise extreme caution with respect to
careless spreading and to wind-drift.
Contact Of Some Products On
Some Plants Can Be Fatal
If a dial setting is not found, use the size and weight
comparison table found in this manual. Determine a
dial setting on the low side. If the setting proves to
be too low, cover the area more than one time. A
higher setting can be used when a proven dial setting is
established.
Remember: Published dial settings are
approximate only. The operation of the spreader, the
condition of the material (damp or dry or over-pulverized)
and weather conditions, are all contributing factors.
For these reasons, it is often a good idea to spread the
area 2 times - or one-half rate - in cross directions (SEE
INFORMATION ON ONE-HALF RATE DIAL SETTINGS).
One-half rate dial settings are highly recommended under
damp and humid conditions.
Rotary Agitator
Use the rotary agitator only if needed. Free-flowing,
lump-free materials will not require the agitator. The
rotary agitator is easily installed or removed. Note the
clockwise rotation and sweep. Place felt washer around
spinner shaft before inserting agitator.
1008192 Rev. A9
READ BEFORE USING
Now You Are Ready To Put
Material In The Hopper
WARNING: Avoid Injury! Chemicals can be
dangerous. Avoid injury to operators or bystanders.
• Make sure the rate gate is in the closed position.
• Read chemical container label for handling
instructions. A Material Safety Data Sheet (MSDS)
should be supplied by the chemical dealer and
provides proper safety information.
• Wear proper clothing and safety equipment while
handling or applying chemicals.
• Prohibit all smoking, drinking, and eating around
chemicals.
• When spreading products containing herbicides,
exercise extreme caution with respect to careless
spreading and to wind-drift. Contact Of Some
Products On Some Plants Can Be Fatal.
• Fill the spreader on a flat, level surface only. Fill on
sidewalk, driveway, cardboard, etc. to avoid material
loss.
• When filling hopper with material, always use screen
to help break up clumps.
Now You Are Ready To Spread
• Keep spinner blade clean. Excess material build-up
can cause an uneven spread pattern.
• Keep the impeller level when spreading.
• DO NOT overload. Maximum capacity of 8020
Series is 80 lbs. Maximum capacity of 9020 Series
is 110 lbs.
• DO NOT use on windy days.
• Spread header strips at the ends of the area
OPPOSITE of the direction of spreading. This will
provide a "turn-around" area, an area to re-align the
spreader for the return spread.
• Example shown is for 6 ft. wide spread. Make the
first spread pass at one-half the spread width from
the edge of the spreading area or in this case,
approximately 3 feet (or one big step).
• Additional spreading passes will be at the full spread
width or approximately 6 ft. apart.
• TAKE A SIGHTING AT THE FAR END. Keep your eye
on the sighting as you spread. You will not need
to wonder where you are or where you have been.
Continue until spreading is completed.
• Left over fertilizer can be spread under trees and
other high feeding areas without showing "edge of
spread" lines.
Tip: When not spreading, and if pushing the spreader
some distance, tip the spreader so only the idle wheel is
on the ground.
Header
6’ 6’3’
Header
Cleaning The Spreader Is Part
Of The Spreading Job
Clean and oil spreader immediately after each use.
Method #1 - Wipe spreader thoroughly with an oily cloth.
Oil all bearings and bearing areas.
Method #2 - Wash, rinse, and dry the spreader. Note:
Drying takes time. Moisture trapped in bearing areas is
slow to go. Immediately after drying - oil all bearings and
moving parts. Make certain all operations are thorough.
NOTE: Good "Dry Cleaning" is preferable to poor "Wet
Cleaning".
• It is virtually impossible to have rust and corrosion on
a clean, dry, oiled surface.
• Again - just before using - oil all bearings and moving
parts.
• In storage, ideally the spreader should be hung by
the handle. In any case, do not pile weight on the
spreader, as excess weight over a period of time can
distort the tires.
Oil Bearings And All Moving
Parts
Make sure the spreader is running freely!
1008192 Rev. A 10
Particle Size
NOTE: Dial Settings Are Approximate Only !
Lbs. per
1000 sq. ft.
Product
Fine Pellets
1
2
3
2
4
6
2
4
6
1
2
3
2
4
6
2
4
6
Dial Settings
Full Rate
Once Over
3.6
4.0
4.2
3.7
4.7
5.2
3
4.2
4.5
3.5
4.2
4.7
3.5
4.2
5.2
3.8
4.9
5.9
Dial Settings
Half Rate
Twice Over
3.1
3.5
3.7
3.2
4.1
4.5
2.2
3.7
4
3
3.7
4
3
3.8
4.5
3.3
4.1
4.9
Mixed Fine
Pellets
Small Pellets
Nitrogen Pellets
Medium Size
Medium Pellets
And Granuals
Large Heavy
Pellets
GRASS SEED SPREADING CHART
Product Bag
Weight
Sq. Ft.
Coverage
Dial Setting
Full Rate
Dial Setting
Half Rate
Spread
Width
Blue Grass or Red Top .5 lbs. 1,000 1.25 4
1 lbs. 1,000 2.0 4
2 lbs. 1,000 2.5 4
Park, Merion, Delta, or Kentucky Bluegrass .5 lbs. 1,000 2.5 4
1 lbs. 1,000 3.0 4
2 lbs. 1,000 3.5 4
Hulled Bermuda 2 lbs. 1,000 2.75 2.25 6
3 lbs. 1,000 3.0 2.5 6
4 lbs. 1,000 3.25 2.75 6
Mixtures Including Coarse Seeds 2 lbs. 1,000 6.0 6
4 lbs. 1,000 7.0 6
6 lbs. 1,000 7.0 6
Rye Grasses or Tall Fescue 2 lbs. 1,000 6.0 6
4 lbs. 1,000 7.0 6
6 lbs. 1,000 7.75 6
Dichondra 4 oz. 1,000 1.9 8
8 oz. 1,000 2.1 8
12 oz. 1,000 2.5 8
Pensacola Bahia 4 lbs. 1,000 4.5 3.75 7
5 lbs. 1,000 4.75 4.0 7
6 lbs. 1,000 5.0 4.25 7
This manual suits for next models
1
Table of contents
Other SPYKER Spreader manuals
SPYKER
SPYKER BCS25 User manual
SPYKER
SPYKER R28-1824 User manual
SPYKER
SPYKER P20-5010 Series User manual
SPYKER
SPYKER S60-12020 User manual
SPYKER
SPYKER S30 Series User manual
SPYKER
SPYKER S40 Series User manual
SPYKER
SPYKER S80-12010 User manual
SPYKER
SPYKER S100-12010 User manual
SPYKER
SPYKER PRO Series User manual
SPYKER
SPYKER S100-12011 User manual
Popular Spreader manuals by other brands
Fisher
Fisher POLY-CASTER 78601 owner's manual
TurfEx
TurfEx RS7200 Owner's/operator's manual
Ferris
Ferris Pathfinder Series Operator's manual
Fayat Group
Fayat Group DYNAPAC S100 operation & maintenance
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Operator's manual & parts list
EASTMAN
EASTMAN CR 500 instruction manual
