Spectra Precision GL6X2N Installation guide
May 2017 GL6X2N
Hands-On training
a - Keypad/LCD-Display
b - Handle
c - Rotor
d - Roll Cage
e - Axes Alignment Marks
f - Sighting Guides/Scope Mounts
g - Battery door
h - Rubber Cover/Recharge Jack
i - 5/8” x 11 Tripod Mounts
j - Rubber Feet
k -Turnable Legs
l - Plus and Minus Battery
Diagrams
GL612N/622N Components
a
b
c
e
d
f
i
g
h
j
k
i
l
Powering the GL612N/GL622N
1 –GL is shipped with a rechargeable NiMH
battery pack (Q104667).
2 –The charger (Q104781) can be used as a
power supply when used Indoors
3 –The rechargeable battery pack can be
charged inside as well as outside of the
unit
4 –Alkaline batteries can be used as a backup
5 –An optional external power cable
(Q104802) is available too
6 –Plus and minus symbols indicate
how to put the alkalines into the
battery compartment
Powering the RC602N
1. Open the battery door using a coin or similar pry
device to release the battery door tab on the RC602N.
RC602N will be shipped with alkaline batteries
Rechargeable batteries can be used optional but need
to be charged externally
2. Insert two AA batteries noting the plus (+) and minus (-)
diagrams inside the battery housing.
3. Close the battery door. Push down until it “clicks”
into the locked position.
Battery status laser Battery Status Remote Control
Mask selection Radio Connectivity
Rotation speed HI alert
Standard Display
Button 1: MENU
Button 2: Grade Entering Mode
Button 3: Manual mode
Button 4: Rotation/Scan
Button 5, 8: up/down arrow buttons
Button 6, 7: left/right arrow buttons
Button 9: ON/OFF button
1 second to turn on the unit;
2 seconds to turn off the unit.
Leveling/Standby –LED (green/red)
Depending on the setup (horizontal) and if a grade value has been
dialed in, the unit starts the temperature/reference check while the
thermometer symbol is flashing.
Don’t start a menu function before the reference check has been
finished.
When the temperature/reference check has been finished, the standard
display appears and the bubble symbols flash until self-leveling has
been completed.
If the self-leveling can’t be finished based on the selected sensitivity, an
error message appears
Turning On/Off the Laser
X-Y- grade entering: Digit Select mode (Default)
button 2: Grade Entering Mode.
button 1quick set to 0%
button 2change the sign of the grade value
Press and release button 5 or 8 (down or up) to move the cursor to the X- or Y-axis.
Pressing and releasing button 6 or 7 (right or left) moves the cursor to the right/left.
Use button 1 or 2 (Plus or Minus) to set the desired digit.
button 3return to the standard display
The laser will self-level to the required grade position after confirming the grade change with button 4.
Note: The bubble symbols at the laser’s LCD will flash until the laser has been self-leveled to the requested
grade position.
Standard Features
X-Y-grade entering
Step and Go mode
Quickly press and release button 2starts the grade entering mode.
Both grade values will be shown.
Press/release button 1grade reverse Y
Press/release button 2grade reverse X
Press/release button 3return to the standard display.
Quickly press and release button 4to confirm the selected grade
value and return to the standard display
Press and hold button 6 or 7 (left/right) to change X- axis grade value
after the comma; press and hold buttons 6 + 7 simultaneously starts X-axis quick change mode
where the grade value in front of the comma will be set to 0% and then starts changing in 1%
increments.
Press and hold button 5 or 8 (up/down) for changing Y -axis grade value; press and hold buttons 5 +
8 simultaneously starts Y - axis quick change mode where the grade value in front of the comma will
be set to 0% and then starts changing in 1% increments
Note: When the grade value for either axis reaches its highest amount, the grade value switches to the
lowest value for that axis. For example, the value switches from +25% to -25%.
The laser will self-level to the required grade position after confirming the grade change with button 4.
Note: The bubble symbols at the laser’s LCD will flash until the laser has been
self-leveled to the requested grade position.
Standard Display
Standard Features
Using the Rotation mode
Repeatedly pressing the button 4 toggles through 300, 600, 750 rpm regardless if the unit is in automatic or
manual mode.
Manual mode
Pressing and releasing button 3 at the Standard Display activates/deactivates the manual mode
regardless if set up horizontal or vertical.
Manual mode is indicated by horizontal lines next to the axes symbols. An additional bubble helps to adjust
the laser on the cross axis when set up vertical.
In Manual mode (horizontal), the Y-axis can be sloped by pressing the Up-(5) and Down-(8)- Arrow
buttons on the laser‘s keypad or the remote control. Additionally, the X-axis can be sloped by pressing
the Left-(6) and Right-(7) Arrow-buttons on the laser or remote control.
In vertical mode, the up and down arrow buttons adjust the Z-axis slope, and the left and right arrow
buttons align the laser beam to the right/left side.
To resume automatic self-leveling mode, press the manual button 3 again.
Standard Features
Menu Functions (Radio controlled)
Press and release button 1 at the Standard Display to enter the MENU.
The menu offers always only the features which can be selected depending on the setup (horizontal or vertical).
The selected icon will be highlighted. A down arrow at the the right site indicates that the user can scroll down
through the menu using the button 8 (down arrow).
Note: As soon as the menu has been opened, button 2 (question mark) can be used to open a help text which
explains the selected function more in detail.
After going to the next menu row, a up/down arrow at the the right site indicates that the user can scroll
up/down through the menu rows (4 different screens) using the buttons 5/8 (up/down arrows).
Pressing and releasing button 3 changes the unit always back to the standard or previous display.
Press and release the buttons 6/7 until the desired icon at the selected menu row is highlighted.
Press and release button 4 to open the submenu OR start the selected function.
Menu functions when set up horizontal (GL622N)
Menu functions when set up vertical
Special MENU Features
PlaneLok Grade
Match Axis Align Mask Mode Standby Reference
Check Settings Info Service
PlaneLok Mask Mode Standby Line Scan Settings Info Service
Table of contents
Other Spectra Precision Laser Level manuals
Spectra Precision
Spectra Precision LL300S Instruction manual
Spectra Precision
Spectra Precision AL28M User manual
Spectra Precision
Spectra Precision LL100N Assembly instructions
Spectra Precision
Spectra Precision LL300S User manual
Spectra Precision
Spectra Precision 1452GC User manual
Spectra Precision
Spectra Precision LL300S User manual
Spectra Precision
Spectra Precision GL412N User manual
Spectra Precision
Spectra Precision Trimble UL 633N User manual
Spectra Precision
Spectra Precision LL300S Installation guide
Spectra Precision
Spectra Precision LL300 User manual
