Spark MF910 User manual
Page 1 of 34
4G WI-FI
MF910 - 4G WI-FI HOTSPOT
USER MANUAL
Copyright © 2014. All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without the prior
written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make modifications on errors or
update specifications without prior notice.
Version 1.1September 2014
Page 2 of 34
CHECK YOUR SYSTEM REQUIREMENTS
Your 4G Wi-Fi Hotspot will connect to any Wi-Fi enabled device that supports
Wi-Fi 802.11 b/g/n
A web browser is required to log in to your Wi-Fi Hotspot if you wish to make any
configuration changes.
USB driverless connection is also supported for Windows (not RT), and MAC
operating systems:
•Windows 8 (not including RT) / 7 / XP / Vista
•MAC OS X 10.5, 10.6, 10.7, 10.8, 10.9
Using the USB connection requires administrator rights to install and run the
software.
We suggest you switch off your anti-virus software before connecting the hotspot
- In some cases protection software can prevent automatic installation.
It is possible to start the installation process manually by clicking the Autorun icon
when it appears.
Page 3 of 34
GET TO KNOW YOUR DEVICE
Page 4 of 34
INSERT YOUR STANDARD SIZED SIM CARD
This device supports a Standard sized SIM card ONLY. Do not use a microSIM or
SIM card adaptor which may damage your device.
1. Locate the SIM slot on the side of the device as shown above.
2. Open the SIM slot cover.
3. Insert your SIM card carefully as shown. The gold contacts must be facing up
towards the screen with the cut corner towards the middle of the device.
4. Push the SIM fully home until it clicks into place.
5. For reference the Reset button is also located under the SIM slot cover.
6. Note: If you replace the SIM card with the device powered On, it will restart to
read the new SIM card.
IMPORTANT
This device supports a standard SIM or 2FF size.
Do not insert a micro SIM (3FF) or use a micro to mini SIM adaptor.
Use of 3rd party adaptors or non approved SIM card can damage your device.
Physical damage to the SIM card slot is not covered by warranty and will make
your device unusable.
TIPS
Remember to keep your plastic SIM card holder. It has a record of your SIM card
details which you should keep handy.
The Reset button is located under the SIM slot cover. With the device switched on,
press the hold the Reset button until the device restarts. A reset will restore all
settings to factory default.
Page 5 of 34
CHARGE YOUR 4G WI-FI HOTSPOT
Connect your charger as shown. Take care to check the orientation of the charger
lead and insert carefully into the charging port on the device.
•Only use the genuine charger and USB lead provided. Use of third party
adaptors can damage your device.
•Typical charging time is 3-4 hours using the standard charger. Charging from a
USB source (ie laptop) will take longer.
•During periods of high continuous activity with multiple users, high download
rates or low network signal, charging by USB will not have sufficient current to
charge the device. In this situation the battery will discharge so it is preferable
to use the mains charger.
•Always insert and remove the charging lead with care and take care not to trip
or pull on the lead harshly which could damage your device.
•Physical damage to the charging port is not covered by warranty.
•If the device is off while charging, press the power key as normal to switch on
the device.
•The device can be left always on and connected to the charger if required.
•During periods of high continuous activity, high download rates or low network
signal it is normal for the device to get hot.
•If the internal temperature of the device exceeds 45C then the battery cannot
be charged due to safety limitations with Li-ion batteries.
Page 6 of 34
POWER UP YOUR 4G WI-FI HOTSPOT
Press and hold the Power key for 1-2 seconds until the display lights up.
The Wi-Fi hotspot will be available after about 20 seconds.
Check the condition of your Wi-Fi hotspot as shown by the display.
To switch your device Off, press and hold the power key for 5 seconds until the
display starts to shut down.
DISPLAY LAYOUT AND ICONS
During periods of inactivity it is normal for the display to turn off to preserve
battery life. Press the power key briefly to confirm the device status if required.
CONNECT DEVICES BY WI-FI
Your Wi-Fi hotspot can connect up to ten devices via Wi-Fi providing internet
access for all your devices on the go.
•On the devices you wish to connect make sure Wi-Fi is switched on, then search
for Wi-Fi devices.
•The Wi-Fi hotspot will show up as MF910-xxxxxx, click on this device to connect.
•Consult your device display and enter the default Password which is case
sensitive. Any letters entered must be in upper case (capitals).
Connection example for Windows 7 computer:
Page 7 of 34
1. On your task bar, next to the clock, click on the Network Interface icon
2. Click on the Wireless device called MF910-xxxxxx
3. Enter the password exactly as shown on the display observing the correct case
for all letters
4. With Connect Automatically enabled your computer will remember the
password and connect to your Wi-Fi device when it is on and in range.
TIP
It is also possible to connect via USB connection. See later for details.
QUICK REFERENCES
Browser home page http://192.168.0.1
Administrator login password
Default SSID MF910-xxxxxx
This is displayed on the screen when the device is
powered up. This can be switched off via the
Settings > Wi-Fi menu
Default Wi-Fi Key 10 characters which are case sensitive.
This is displayed on the screen when the device is
powered up. This can be switched off via the
Settings > Wi-Fi menu
Restore defaults From the powered up state:
Open the SIM slot on the device. Locate the Reset
button and use a small object such as a pin or
paperclip to press the button.
Hold the Reset button for five seconds until the
display shows ‘Resetting’
All passwords and settings will be restored to
defaults and the hotspot will reboot.
Use the default credentials on the screen to log
back onto your device.
Page 8 of 34
LOG INTO THE WEB INTERFACE, MODEM LOGIN PAGE
•To access the modem configuration pages, open a browser and go to
http://192.168.0.1
•The default login password is ‘password’
•The first page shows a brief summary of the modem status:
Page 9 of 34
STATUS ICONS – WEB INTERFACE
NO NETWORK ACCESS
•No Network Access can be any of the following conditions:
•A missing, faulty or incorrectly inserted SIM. Check you have inserted your SIM
card the right way and fully pushed it home until it clicks into place.
•A PIN locked SIM card. Log into the web interface then enter the PIN code for
your SIM card.
•A PUK locked SIM card. You may have entered the wrong PIN code too many
times. Contact Spark to obtain your PIN Unlocking Key (PUK) code. Log into the
web interface to enter your PUK and PIN code
•A PUK blocked SIM card. If you enter the wrong PUK code too many times the
SIM card is permanently blocked. Contact your dealer to obtain a replacement
SIM card.
•No Service, you are out of network coverage.
INTERNATIONAL ROAMING
•The Roaming icon indicates you are connected to a foreign network.
•If Roaming is enabled on your data plan then roaming data charges will apply
when connected via a roaming network.
•Contact your carrier to determine your data charges.
Page 10 of 34
INSTALLATION NOTES
•If you choose to install the device via the USB connection then a CDROM drive
will pop up on first installation.
•Double-click Setup.exe to install the software.
•The installation will create a new shortcut on your desktop and a new program
listing under Start-Programs.
•If you have problems with the installation please contact your supplier or see
our website, www.zte.co.nz for more assistance and FAQ’s.
•If you can’t connect to the internet check your SIM card is inserted correctly,
contact your service provider and check your account is active.
•To uninstall the application:
Windows users: Start > SPARK 4G WI-FI > Uninstall
MAC Users:
•Double click the Spark Modem CDROM on the desktop to install the modem.
•To uninstall, go to Applications and run Uninstall SPARK 4G WI-FI
WEB INTERFACE GUIDE
HOME TAB
Table of contents
