Sony KL-37W1U User manual

Models KL-37W1U KL-50W1U KL-50W2U LE-1 chassis

To enter the service mode:

Turn the mains power on while holding the "PROG +" and the "PROG -"

buttons on the set simultaneously.

"TT" will appear at the top right hand corner of the screen

Press "01" on the remote control to see the service menu on screen

Press the "arrow up" and the "arrow down" buttons on the remote

control to navigate the menus

Press the "OK" button to select an adjustment

Press the "arrow up" and the "arrow down" buttons to highlight an

adjustment, and press the "OK" button to allow adjustment.

Use the "arrow up" and the "arrow down" buttons to adjust the value

Press the "OK" button to store

Turn off the power to exit the service mode

Test mode 2 allows entry of TT numbers to perform some functions. The

important numbers for this chassis are given below

TT00 switch the TT mode off

TT08 set the set to shipping condition

TT15 Factory reset values

TT16 User defined reset values

TT16 loads the contents of the NVM when the set was last switched off

TT15 loads the factory defaults. To do this press TT15 followed by

TT16.

----------------------------------------------------------------------

----------

Models : KV25F1U - KV29F1U - KV25F2U - KV29F2U - KV25F3U -

KV29F3U -

KV25X1U - KV29X1U - KV24WX1U - KV28WX1U - KV24WS2U -

KN28WS2U -

KV28WF1U - KV32WF1U - KV29FX11U - BE-3D chassis

KV28DS20U KV28DX20U KV32DS20U KV32DX20U BE-3E chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Press the "MENU" button on the remote control to bring up the test

screen

Use the joystick on the remote control to navigate the service menu

(< > ^ v keys BE-3E)

Press the right joystick to enter the selected adjustment

Turn off the power to store and exit the service mode

Test mode 2 allows entry of TT numbers to perform some functions. The

important numbers for this chassis are given below

TT00 switch the TT mode off

TT08 set the set to shipping condition

TT24 Set CTV to UK model (PAL I)

TT44 Set all favourite pages to 100

To re-initialise the NV Ram follow the procedure below:

Set the TV to channel 59

Select TT49

Switch off at the mains supply, wait for one minute and switch the

set back on

Select channel 59, and enter the service mode

Select TT24, (UK destination)

Select TT42, (general reset)

Switch off at the mains, wait for one minute and switch on again

Auto tune the channels and carry out a complete adjustment on the set

----------------------------------------------------------------------

----------

Models KP-41S3U RE-1 chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Use buttons "1" and "4" on the remote control to navigate the service

Use buttons "3" and "6" to adjust the selected data

Press the "MUTE" button and then the "0" button to store the data

Press the "5" button and then the "0" button to initialise the set.

(Note, this is an extreme measure and should be used with caution!)

Turn the set off to exit

----------------------------------------------------------------------

----------

Models KP-41S3U RE-1 chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Use buttons "1" and "4" on the remote control to navigate the service

Use buttons "3" and "6" to adjust the selected data

Press the "MUTE" button and then the "0" button to store the data

Press the "5" button and then the "0" button to initialise the set.

(Note, this is an extreme measure and should be used with caution!)

Turn the set off to exit

----------------------------------------------------------------------

----------

Models KP-41DS1U RE-2D chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Use the JOYSTICK Up / Down on the remote control to navigate the

service menu

Move the JOYSTICK to the right > to enter the selected adjustment

Press OK on the JOYSTICK to EXIT

Press the "MUTE" button and then the "0" button to write data

Press the "On Screen Display" button to copy data

Turn the set off to quit the service mode when adjustments are

complete

----------------------------------------------------------------------

----------

Models KV-14V4U TE-1 chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Use buttons "1" and "4" on the remote control to navigate the service

Use buttons "3" and "6" to adjust the selected data

Turn off the power to store and exit the service mode

The codes on screen are as follows:

ODL Power On Delay

OSH On screen H-position

MUT FTZ muting on *Do not adjust

VAM V. size

VBC V breath correct *Do not adjust

PAM Parabola amp. *Do not adjust

PTI Parabola tilt *Do not adjust

VLI V-linearity

CCR Corner correction *Do not adjust

HAM V. cent *Do not adjust

BIN Blue intensity

GIN Green intensity

RIN Red intensity

CLS Colour system

SCO Sub contrast

SBR Sub brightness

SSA Sub saturation

SHU Sub hue

SSH Sub sharpness

G2 adj G2 adjustment

32K adj

----------------------------------------------------------------------

----------

Models KV-16WS1U KV-21X1U KV-21X4U KV-20WS1U BE-5 chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Press the "MENU" button on the remote control to see the service menu

on screen

Use the "blue" button and the "green" button on the remote control to

navigate the service menu

Use the "Yellow" button and the "red" button to adjust the selected

data

Turn the set off to exit and store

Test mode 2 allows entry of TT numbers to perform some functions. The

important numbers for this chassis are given below

TT00 switch the TT mode off

TT08 set the set to shipping condition

TT26 Set CTV to UK model (PAL I)

TT41 Re-initialise NVM

TT43 Re-initialise geometry settings

Note: For TT numbers above 41, the channel number needs to be 59

----------------------------------------------------------------------

----------

Models. KV-32WS4U KV32WX4U KV32WX2U AE-4 chassis

To enter the service mode:

Turn the mains power on while holding the "PROG +" and the "PROG -"

buttons on the set simultaneously.

"TT" will appear on the top right hand corner of the screen.

Press "MENU" on the remote control to get the service menu on screen

Navigate the menu by moving the joystick up and down.(green and blue)

Press the joystick down to select an adjustment.

Turn TV off to exit service mode

Test mode 2 allows entry of TT numbers to perform some functions. The

important numbers for this chassis are given below

TT00,10,20,30,40 pressing these numbers will switch the TT mode

off

TT01 switch service menu on

TT08 set the set to shipping condition

TT21 picture rotation automatic function

TT25 Status menu display

TT49 New initialisation

----------------------------------------------------------------------

----------

Models. KV28FD1E KV28FD1K KV32FD1E KV32FD1K GE-1 chassis

To enter the service mode:

Turn the mains power on while holding the "PROG +" and the "PROG -"

buttons on the set simultaneously.

"TT" will appear on the top right hand corner of the screen.

Press "MENU" on the remote control to get the service menu on screen

Navigate the menu by moving the joystick up and down.(green and blue)

Press the joystick down to select an adjustment.

Turn TV off to exit service mode

The main adjustments are:

MCP CXA2101 - picture (colour, drives, brightness etc)

Deflection control SDA9361 - geometry

----------------------------------------------------------------------

----------

Models KV-29X5U FE-1 chassis

To access the service mode:

Turn the set on and then put into standby

Press the On Screen Display button

Press the "5" button

Press the "VOLUME +" button

Press the "TV" button

Use buttons "^"(Green) and "v"(Blue) on the remote control to

navigate the service menu

Press YELLOW button to enter required menu

Use buttons "<" and ">" to adjust the selected data

Press the "MENU" button to store the data and exit

Test Menu

Picture - (RGB. Drives & Cut offs, Sub Colour, Sub brightness)

Geometry - (Vert. and Horiz. adjustments)

Sound - (NICAM Information)

TV Status - (Destination and Country info.)

AGC. Adjust

Technical

----------------------------------------------------------------------

----------

Other manuals for KL-37W1U

This manual suits for next models

Table of contents

Other Sony TV manuals

Sony

Sony BRAVIA KD-65A8H User manual

Sony

Sony Trinitron KV-13TR28 User manual

Sony

Sony FD Trinitron KV-28LS35U User manual

Sony

Sony KV-32LS60K User manual

Sony

Sony BRAVIA KLV-24P413D User manual

Sony

Sony Esprit TAV-L1 User manual

Sony

Sony TRINITRON KV-25C5A User manual

Sony

Sony Trinitron KV-20V50 User manual

Sony

Sony KV-EF34N90 User manual

Sony

Sony Trinitron KV-32CX10 User manual

Sony

Sony BRAVIA KDL-70XBR7 User manual

Sony

Sony BRAVIA KDL-40E55 Series User manual

Sony

Sony WEGA KV-XV29 User manual

Sony

Sony BRAVIA OLED KD-77AG9 User manual

Sony

Sony Bravia KDL-55W829B User manual

Sony

Sony BRAVIA KDL-48W655D User manual

Sony

Sony Grand WEGA KDF-E60A20 User manual

Sony

Sony KDL-26U4000 User manual

Sony

Sony TRINITRON KV-AR25M90B User manual

Sony

Sony BRAVIA KDL-40R357F User manual

Sony

Sony KD-75ZD9 User manual

Sony

Sony BRAVIA KDL-32R420A User manual

Sony

Sony BRAVIA KDL-60EX701 User manual

Sony

Sony KDS-70Q006 - 70" Qualia 006 User manual

Popular TV manuals by other brands

Philips

Philips Colour Television Service manual

Toshiba

Toshiba 27A10 owner's manual

Philips

Philips 42PF9630A/37 user manual

Hitachi

Hitachi 32FX48B operating guide

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Service manual

Changhong Electric

Changhong Electric uhd55b6000is Operation manual

Philips

Philips Matchline 21CE7551 operating instructions

Panasonic

Panasonic Genus TX-G10 operating instructions

Toshiba

Toshiba 19A20 Service manual

Philips

Philips 25PT4523-16 manual

Philips

Philips PR0930X3 owner's manual

Philips

Philips Brilliance 231P4QPY user manual

Samsung

Samsung 55S9 B Series Quick setup guide

Philips

Philips 32HF9385D Käyttöopas

Sharp

Sharp LC-40FI5012E user manual

Loewe

Loewe Table Stand Reference 55 user guide

Philips

Philips 32PFH5300 Service manual

Sylvania

Sylvania 6427FB owner's manual