Sony SU-P50T2 User manual

4-100-124-41 (1)

Table-Top Stand

Instructions

SU-P50T2

2(GB)

Thank you for purchasing this product.

To Customers

Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers

or contractors and pay special attention to safety during the installation. Sony is not liable for any damages or

injury caused by mishandling or improper installation.

WARNING

If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire.

This instruction manual shows the correct handling of the product and important precautions necessary to prevent

accidents. Be sure to read this manual thoroughly and use the product correctly. Keep this manual available for

future reference.

For Sony dealers

Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly to do

the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper

installation. Please give this manual to the customer after installation.

On Safety

Products by Sony are designed with safety in mind.

If the products are used incorrectly, however, it may result in a serious injury through fire, electric shock, the

product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such

accidents.

CAUTION

This Table-Top Stand is intended for use only with the following products. Use with other apparatus is capable of

resulting in instability causing possible injury.

Specified product (As of December 2004): Flat Panel Colour Television

(KE-50MR1/KE-61MR1/KE-MR50/KE-MR61)

(GB)3

For Customers

WARNING

If the following precautions are not observed, serious injury or death through fire, electric shock, the

product toppling over, or the product dropping can result.

Be sure to subcontract the installation to Sony dealers.

If persons other than Sony dealers do the installation work, this may result in serious injury, as the Display Unit is

very heavy.

Be sure to take measures to prevent the stand from toppling over.

If you fail to do so, the TV may topple over and cause injury. Anchor the TV to a wall, pillar, etc., to prevent

toppling over.

Be sure to install the Table-Top Stand on a solid and flat surface.

Do not install the Table-Top Stand so that it leans in one direction. If you do so, the

Table-Top Stand may topple over or the Display Unit may fall. This may cause

injury or property damage.

Be sure to install the Table-Top Stand on a stable surface.

If you install the Table-Top Stand on an unstable surface, it may lose its balance

and topple over or fall off. This may cause injury or property damage.

Do not lean on or hang from the Display Unit with the Display Unit installed

on the Table-Top Stand.

The Table-Top Stand may topple over, or the Display Unit may fall and cause

serious injury or death.

Do not cover the ventilation hole of the Display Unit.

If you cover the ventilation hole (with a cloth, etc.), heat may build up inside and

cause fire.

English

4(GB)

Do not allow the mains lead or the Display Interface Cable to be pinched.

•Do not allow the mains lead or the Display Interface Cable to be pinched when

you install the Display Unit on the Table-Top Stand. If the mains lead or the

Display Interface Cable is damaged, this may result in a fire or an electric shock.

•Do not step on the mains lead or the Display Interface Cable when you carry the

Table-Top Stand. The mains lead or the Display Interface Cable may be

damaged, and this may result in a fire or an electric shock.

Be sure to carry the stand in the manner shown in this manual.

If the Table-Top Stand is carried incorrectly, it may topple over and cause injury.

Do not stumble over the mains lead or the Display Interface Cable.

If you stumble over the mains lead or the Display Interface Cable, the Table-Top Stand may topple over and cause

injury.

Do not carry the Table-Top Stand with Display Unit installed on it.

Be sure to remove the Display Unit before attempting to carry the Table-Top Stand.

If you fail to do so, the Display Unit may fall and cause bodily injury.

CAUTION

If the following precautions are not observed, injury or property damage may occur.

Do not install any equipment other than the specified product.

This stand is designed for use with the specified product only. If you install equipment other than specified, it may

fall and cause injury or property damage.

Be sure to use the securing screws.

If the securing screws are not used, the Display Unit may fall and cause injury.

(GB)5

Notes on installation

• When assembling, lay the packing materials on the floor to avoid damage to the floor.

•Install the stand on a solid and flat surface. Do not allow the stand to be installed at an angle or incline. To avoid

this, observe the following precautions.

– If you install the stand on a soft surface such as a mat or a carpet, lay a board over the designated location

beforehand.

– Do not install the stand in a place subject to direct sunlight or near a heater.

–Do not install the stand in a hot or humid place, or outdoors.

Note on use

To keep the stand clean, occasionally wipe the stand with a dry soft cloth. Stubborn stains may be removed with a

cloth slightly dampened with diluted detergent. Then wipe the area with a dry soft cloth. Do not use chemicals,

such as thinner or benzine, as they damage the finish of the stand.

Assemble the Table-Top Stand

To Sony Dealers

The following instructions are for Sony Dealers only. Be sure to read safety precautions described above

thoroughly and pay special attention to safety during the installation, maintenance, checking and repair of this

product.

Be sure that two or more persons do the installation work.

Be sure that two or more persons install the Display Unit on the Table-Top Stand. If one person does the installation

work alone, this may result in an accident or an injury.

Be sure to assemble the Table-Top Stand securely following the instructions in

this manual.

If any of the screws are loose or fall out, the Table-Top Stand may lean and topple

over, or the Display Unit may fall. This may cause injury or property damage.

Be careful not to hurt your hands or fingers when assembling the Table-Top

Stand.

Be careful not to hurt your hands or fingers when assembling the Table-Top Stand or when installing the Display

Unit.

Be sure to install the Display Unit securely, following the proper procedure.

Be sure to tighten the screws firmly.

If the Display Unit is not installed securely, it may fall and cause injury.

For Sony Dealers

6(GB)

Check the parts

Name Quantity Name Quantity

Main bracket Countersink screw

Securing screw

Stand 2

1Cable clamper

Prepare a Phillips screwdriver beforehand.

Install the main bracket

Align the main bracket over the screw holes on the stand. Then fasten

the main bracket to the stand using 10 countersink screws.

Be sure that two or more persons hold the parts during this procedure.

Tighten the 10 countersink screws once again after screwing them temporarily.

Note

Be sure to hold the stand firmly and keep it stable.

Caution

When using an electric screwdriver, set the

torque setting to about 2.45N·m.

Do not use an impact driver. If you use an

impact driver or an electric screwdriver with

the torque setting out of the specified range,

screws may be excessively tightened, which

may damage the screws or product. The

stand may fall and serious injury may result.

Countersink

screws

Main bracket

Stand

(GB)7

Install the Display Unit

WARNING

Be sure to complete the installation before connecting the mains lead to the wall socket. If you allow the mains

lead to be pinched under or between pieces of equipment, this may result in a short circuit or an electric shock.

If you stumble over the mains lead or the Display Unit, the stand may topple over and cause injury.

1Install the Display Unit on the Table-Top Stand.

1Connect the mains lead and the Display Interface Cable to the Display Unit.

zTip

See the instruction manual of the Sony

Flat Panel Colour Television for more details on

connecting the mains lead and the Display

Interface Cable.

Notes

•If the weight of the Display Unit is placed on

the speakers, deformation or a loose

connection of the speakers may result. To

avoid this, observe the following. (KE-

61MR1/KE-MR61 only)

– Do not hold the speakers when carrying

the Display Unit.

–When connecting cables to the Display

Unit, place packing material, etc. on the

floor and lay the Display Unit face down

on it so that the speakers on either side of

the Display Unit are clear of the packing

material, etc.

• Be sure to place the Display Unit stably.

•Use soft cloth to protect the screen of the

Display Unit from damage or dirt.

Rear side of the Display Unit

Soft rag

Mains lead

Display

Interface Cable

Soft rag Speaker (right)

Speaker (left)

Packing material,

etc.

Rear side of the

Display Unit

KE-50MR1/KE-MR50

KE-61MR1/KE-MR61

Illustrations without model names that appear from now on are based on the Flat Panel colour television KE-MR50.

8(GB)

2Be sure that two or more persons hold the right and left edges of the top and the under sides of the

Display Unit while fitting the hooks on the rear of the Display Unit into the holes on the fixtures of the

stand. Then confirm that the hooks on the rear of the Display Unit are completely inserted into the four

holes of the fixtures.

Note

Do not stumble over the mains lead or the

Display Interface Cable.

3Slide the Display Unit straight downward until it snaps on.

Notes

•Slide the Display Unit completely down

to the bottom. Confirm that the Display

Unit is installed on the stand

horizontally.

•Be sure to keep the Table-Top Stand

stable while installing the Display Unit.

2Attach the Display Unit to the stand with the two securing screws.

Hook

Securing screws

Side View

Rear side of the

Display Unit

(GB)9

3Route the mains lead and the Display Interface Cable through the stand.

1Attach the cable clamper to the main bracket.

2Draw the mains lead and the Display Interface Cable through the cable clamper and fix them.

3Remove the cable cover from the stand and route the mains lead and the Display Interface Cable inside

the stand.

Cable clamper

Cable cover

10 (GB)

4Reattach the cable cover to the stand.

Anchor attachments

Cable cover

Safety measures to prevent toppling over

WARNING

Be sure to take measures to prevent the stand from toppling over. If you fail to do so, the Table-Top Stand may

topple over during an earthquake and cause injury or property damage. Anchor the Table-Top Stand to a wall,

pillar, etc. to prevent it from toppling over.

Prepare a commercially available rope or chain and wall anchor bracket beforehand.

1Secure the wall anchor bracket to a solid wall or pillar.

2Pass the rope or chain through both holes of the anchor attachments and then tighten the other end of the

rope or chain to the wall anchor bracket.

Wall anchor

bracket

Other manuals for SU-P50T2

Table of contents

Languages:

Other Sony Rack & Stand manuals

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 