Sony FWD-32LX2F User manual
FLAT WIDE DISPLAY MONITOR
FWD-40LX2F
FWD-40LX2X
FWD-32LX2F
FWD-32LX2X
KLH-W32
KLH-W26
PROTOCOL MANUAL
1st Edition
FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
Table of Contents
1. Communication Parameters .......................................................... 1
2. Pin Assignment ...................................................................................... 1
3. Communication Data Format ......................................................... 1
4. General Function ................................................................................... 3
5. Picture/Sound ........................................................................................ 11
6. Size/Shift .................................................................................................. 13
7. Status Enquiry ....................................................................................... 16
8. User Reset ............................................................................................... 20
9. Service ........................................................................................................ 20
1
FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
1. Communication Parameters
Communication Method RS-232C
Synchronous Method Asynchronous
Baud Rate 9600 bps
Character Length 8bit
Parity None
Start Bit Length 1bit
Stop Bit Length 1bit
Flow Control None
2. Pin Assignment
The control command is not acceptable for 3 seconds after
the power is turned on from the standby state and for 5
seconds after the power is turned on when AC is set to ON
from OFF state. Send the command after waiting each
required time. In the case when the power is turned on
from the standby state, the starting up by using the timer
(KLH-W26/W32 does not have this function), the power
key of main unit or the remote commander is included as
well as the command from RS-232C.
12345
Monitor side : D-sub
_External view _
6789
12345
6789
Host side : D-sub 9pin
_External view _
FWD-40LX2F/40LX2X
FWD-32LX2F/32LX2X
Personal computer
Pin No. Signal
1NC
2 RXD
3 TXD
4NC
5 GND
6NC
7NC
8NC
9NC
Pin No. Signal
1NC
2 RXD
3 TXD
4NC
5 GND
6NC
7NC
8NC
9NC
3. Communication Data Format
(a) Control message
No. Item Value
1 Header 0x8C:Control
2 Category 0xXX
3 Function 0xXX
4 Data1 (Length) 0xXX
5 Data2 (Data1) 0xXX
: : 0xXX
: : 0xXX
X Data (X-3) 0xXX
X+1 Check Sum 0xXX
*Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
*Set the command interval to 500 ms or more when transmitting the
Control command continuously.
*Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
(b) Enquiry message
No. Item Value
1 Header 0x83:Enquiry
2 Category 0xXX
3 Function 0xXX
4 Data1 0xFF
5 Data2 0xFF
6 Check Sum 0xXX
*Check Sum: Sum total of 1 to 5. Lower one-byte data is validated when a
value exceeds 255 (1byte).
2FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
(c) Answer message
1Control answer
No. Item Value
1 Header 0x70:Answer
2 Answer*0x00:Completed
0x01:Limit Over
0x02:Limit Under
0x03:Command Canceled
3 Check Sum 0xXX
*0x00:Completed Packet is correctly received and process is
also correctly completed.
0x01:Limit Over Packet is correctly received, but the data
value is over the upper limit.
0x02:Limit Under Packet is correctly received, but the data
value under the lower limit.
0x03:Command Canceled Packet is correctly received, but the data
value is not correct or the request cannot be
accepted in the current host state.
*Check Sum: Sum total of 1 to 2. Lower one-byte data is
validated when a value exceeds 255 (1byte).
2Enquiry answer (Complete)
No. Item Value
1 Header 0x70:Answer
2 Answer 0x00:Completed
3 Return Data Size 0xXX
4 Return Data1 0xXX
: : 0xXX
: : 0xXX
X Return Data (X-3) 0xXX
X+1 Check Sum 0xXX
*0x00:Completed Packet is correctly received and process is also
correctly completed.
*Return Data: Returns the read value.
*Check Sum: Sum total of 1 to X. Lower one-byte data is validated
when a value exceeds 255 (1byte).
3Enquiry answer (Command cancel)
No. Item Value
1 Header 0x70:Answer
2 Answer 0x03:Command Canceled
3 Check Sum 0x73
0x03:Command Canceled Packet is correctly received, but the data
value is not correct of the request cannot be
accepted in the current host state.
4Error answer
No. Item Value
1 Header 0xE0:Answer
2 Answer*0x00:No Function Error
0x01:Check Sum Error
0x02:Data Length Error
3 Check Sum 0xXX
*0x00:No Function Error Packet header, category of function code are not
included in this protocol.
0x01:Check Sum Error Check sum value of received packet is not
correct.
0x02:Data Length Error Packet is correctly received, but the data size is
over the upper limit.
*Check Sum: Sum total of 1 to 2. Lower one-byte data is validated
when a value exceeds 255 (1byte).
3
FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
4. General Function
(a) Mode Control
Syntax Header Category Function Data1 Data2 Check Sum
Control 0x8C 0x00 Code Table (1-a)[a] 0x02 Code Table (1-a)[b] 0xXX
Enquiry 0x83 0xFF 0xFF 0xXX
Answer Header Answer Check Sum
Control 0x70 0x00 0x70 Completed
0x70 0x01 0x71 Limit Over
0x70 0x02 0x72 Limit Under
0x70 0x03 0x73 Command Canceled
Answer Header Answer Return to Data Size Return Data1 Check Sum
Enquiry 0x70 0x00 0x02 Code Table(1-a)[b] 0xXX Completed
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x00 Power*10x00 OFF Yes Yes Enable Enable
0x01 ON
0x01 Input Select*30x08 INPUT1 RGB (Analog) Yes Yes Disable Enable
0x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO*2
0x11 OPTION2 S-VIDEO*2
0x12 OPTION2 RGB*2
0x13 OPTION2 COMPONENT*2
0x44 INPUT2 RGB (Digital)
0x45 INPUT2 DTV (Digital)
0x54 INPUT3 RGB (Digital)
0x55 INPUT3 DTV (Digital)
0x02 Force Status Display 0x00 ON Yes Yes Disable Enable
0x01 OFF
0x03 Audio Mute 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x04 Auto Status Display 0x00 ON Yes Yes Enable Enable
0x01 OFF
0x10 Index Number 0x01-0xFF Yes Yes Disable Enable
0x14 Speaker Out 0x00 ON Yes Yes Disable Enable
0x01 OFF
4FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x18 Sync Mode 0x00 H/Comp Yes Yes Disable Enable
0x01 Video
0x1B Clock Display 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x24 Input Detect (Option1) 0x00 FW12 (HD15) No Yes Disable Enable
0x01 FW10 (VIDEO, S-VIDEO) BNC
0x02 FW11 (BNC)
0x03 Reserved
0x04 FW31/32
0x05 FW50 (RGB)
0x06 FW20 (UART +CTRL-S)
0x07 Reserved
0x08 Reserved
0x09 Reserved
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x25 Input Detect (Option2)*20x00 FW12 (HD15) No Yes Disable Enable
0x01 FW10 (VIDEO, S-VIDEO) BNC
0x02 FW11 (BNC)
0x03 Reserved
0x04 Reserved
0x05 Reserved
0x06 FW20 (UART +CTRL-S)
0x07 Reserved
0x08 Reserved
0x09 Reserved
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x30 PAP*20x00 OFF Yes Yes Disable Enable
0x01 P&P
0x31 Active Picture*20x00 Left Yes No Disable Enable
0x01 Right
0x02 Swap
5
FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x32 Picture Size (P&P)*20x00 Large Left Yes Yes Disable Enable
0x01 Even
0x02 Large Right
0x35 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable
(Left)*20x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S-VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x44 INPUT2 RGB (Digital)
0x45 INPUT2 DTV (Digital)
0x54 INPUT3 RGB (Digital)
0x55 INPUT3 DTV (Digital)
0x36 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Disable Enable
(Right)*20x09 INPUT1 YUV (Analog)
0x0C OPTION1 VIDEO
0x0D OPTION1 S-VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S-VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x44 INPUT2 RGB (Digital)
0x45 INPUT2 DTV (Digital)
0x54 INPUT3 RGB (Digital)
0x55 INPUT3 DTV (Digital)
0x45 Control Mode 0x00 Main +Remocon Yes Yes Disable Enable
0x01 Main
0x02 Remocon
0x03 All Off
0x04 Limited*4
0x46 On Off Timer Mode*20x00 Every Day (Repeat) Yes Yes Enable Enable
0x01 Day Of Week
6FWD-40LX2F/40LX2X/32LX2F/32LX2X
KLH-W32/W26
Code Table (1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x47 On Timer Enable*2bit0 Sunday 1:Enable, 0:Disable Yes Yes Enable Enable
bit1
Monday 1:Enable, 0:Disable
bit2 Tuesday 1:Enable, 0:Disable
bit3
Wednesday 1:Enable, 0:Disable
bit4 Thursday 1:Enable, 0:Disable
bit5 Friday 1:Enable, 0:Disable
bit6 Saturday 1:Enable, 0:Disable
bit7 Every day 1:Enable, 0:Disable
0x48 Off Timer Enable*2bit0 Sunday 1:Enable, 0:Disable Yes Yes Enable Enable
bit1 Monday 1:Enable, 0:Disable
bit2 Tuesday 1:Enable, 0:Disable
bit3 Wednesday 1:Enable, 0:Disable
bit4 Thursday 1:Enable, 0:Disable
bit5 Friday 1:Enable, 0:Disable
bit6 Saturday 1:Enable, 0:Disable
bit7 Every day 1:Enable, 0:Disable
0x65 IP Setting Mode 0x00 DHCP Yes Yes Enable Enable
0x01 Manual
0x02 Speed
0x66 IP Setting Execute 0x00 No No Yes Enable Enable
0x01 Yes
0x67 IP Setting Result 0x00 Done Yes No Enable Enable
0x01 Error 1 (UART Commu.)
0x02 Error 2 (Duplication)
0x03 Error 3 (IP Add Setting)
0x04 Error 4 (GW Add setting)
0x05 Error 5 (DNS1 Setting)
0x06 Error 6 (DNS2 Setting)
0x07 Error 7 (Sbnt Msk Setting)
0x68 Speed Setting 0x00 100 Mbps/Full Duplex Yes Yes Enable Enable
0x01 100 Mbps/Half Duplex
0x02 10 Mbps/Full Duplex
0x03 10 Mbps/Half Duplex
0x04 Auto
0x70 Input Skip bit0 HD15 Yes Yes Disable Enable
bit1 HDMI1
bit2 HDMI2
bit3 Reserved
bit4 Reserved
bit5 Reserved
bit6 Reserved
bit7 Reserved
Other manuals for FWD-32LX2F
4
This manual suits for next models
18
Table of contents
Other Sony Monitor manuals
Sony
Sony Trinitron BVM-A14F5M User manual
Sony
Sony Trinitron CPD-G200 User manual
Sony
Sony SDM-X202 User manual
Sony
Sony CPD-G520P User manual
Sony
Sony Trinitron CPD-220GS User manual
Sony
Sony CPD-E200E User manual
Sony
Sony BVM-1911 User manual
Sony
Sony CPD-G22 User manual
Sony
Sony LMD1750W User manual
Sony
Sony SDM-S91 User manual
Sony
Sony FWD-50PX1 (English: pgs. 52-97) User manual
Sony
Sony HMZ-T3 User manual
Sony
Sony CPD-G520P User manual
Sony
Sony FWD 55W802A User manual
Sony
Sony CPD-9090 User manual
Sony
Sony GXDL52H1 - 52" LCD Flat Panel Display User manual
Sony
Sony SDM-S76D User manual
Sony
Sony LDI-100 User manual
Sony
Sony Trinitron CPD-200GS User manual
Sony
Sony Trinitron CPD-G500J User manual
