Sony BKM-101C User manual

Installation Manual for Dealers

特約店様用取付説明書

Monitors Available for BKM-101C and 102

BKM-101Cおよび102 に対応するモニター

PVM-14M2U/14M2E/14M2A/14M4U/14M4E/14M4J/14M4A/14M4B

PVM-20M2U/20M2E/20M4U/20M4E/20M4J/20M4A

PVM-20S1WU/20S1WE/20S1WA（英文のみ／English only)

BVM-14M4E/20M4E

Monitors Available for BKM-102

BKM-102に対応するモニター

BVM-14M4DE/14M4DJ/20M4DE

3-859-887-06 (1)

コンポ−ネントSDIキット<VIDEO>

BKM-101C

コンポ−ネントSDIキット<AUDIO>

BKM-102

1997 by Sony Corporation

WARNING!

When installing the kit, to prevent shock hazard,

do the following:

• Turn off the whole system connected to the

monitor.

• Unplug all cables, the power cable etc., con-

nected to the monitor.

取り付けの際は、感電を防ぐため、次の項目を必

ず守ってください。

•モニターと接続しているシステムの電源をすべ

て切ってください。

•モニターに接続されている電源ケーブルなど、

すべてのケーブルを外してください。

Ground wire (for SDI

module)

Ground wire (with

faston connector, for

BB board)

To prevent fire or shock hazard, do

not expose the unit to rain or mois-

ture.

The component SDI kit <VIDEO> BKM-

101C is designed to be installed into a

monitor alone. It can also be installed

together with the component SDI kit

<AUDIO> BKM-102.

This Installation Manual explains how to

install BKM-101C and BKM-102.

WARNING

BKM-101C

Spacer*

(with adhesive tapes)

BB board

3-pin connecting cable

(Type A: One end is

shielded.)*

12-pin connecting

cable*

3-pin connecting cable

(Type B: Both ends

have connectors.)

* These parts are not used in the monitors shown

on the cover page.

Parts List

Continue

SDI module

Connector label Adaptor fitting for

20-inch monitor

Screw

+BVTT 4 ×8

×5

Cable clamp

(black)

OUT

COMPONENT SDI

ACTIVE THROUGH

Connecting cables Holder

(for 14-inch

monitors)

×1

Ferrite core (small)

BKM-102

BA board 5-pin connecting cable

4-pin connecting

cable

30-pin flat cable

Screw +BVTP 3×8

×4

Ferrite core (large)

Cable clamp (ø11)

Screw

+PS 4 ×8

×1

×2

×1

×2 ×1

×1

English

Installation Continue

1Remove the rear cover of the monitor.

Remove 10 screws.

3Pull out the connector panel.

2Remove the G board and attach it again as

in the illustration.

G board

4(only for 20-inch monitors, except PVM-

20S1WE/20S1WU/20S1WA)

Install the supplied adaptor fitting for 20-

inch monitors.

Adaptor fitting for

20-inch monitors

Supplied screw

(+BVTT 4 ×8)

2Insert the BA board into the SDI

module.

Use the 30-pin

flat cable with

the metal side

facing up.

BA board

3Insert the 30-pin flat cable connector

into the CN5 terminal on the BV board,

and secure the BA board using the

supplied 4 screws with BKM-102.

4Connect the CN1 terminal on the BA

board to the CN3 teminal on the BV

board, and connect the CN2 terminal on

the BA board to the CN4 terminal on

the BV board, using the connecting

cables supplied with BKM-102.

CN2

CN1

CN4

CN3

4-pin

connecting

cable

5-pin

connecting

cable

Installation

5Install BKM-102 (BA board) in the SDI

module of BKM-101C.

If you do not install the BKM-102, skip step

5 and go to step 6.

1Remove the cover of the SDI module.

Remove 8 screws.

Cover

5Position the connecting cables to the

side of the board.

6Attach the cover of the SDI module

using the 8 screws removed in step 1.

6Connect the supplied connecting cables

and the ground wires (for the SDI module)

to the SDI module.

1Remove the screws from the SDI

module, and connect the ground wires

to the SDI module using these screws.

2Insert the connectors of the connecting

cables to the terminals on the SDI

module.

3(for monitors PVM-20S1WE/20S1WU/

20S1WA only)

Attach the supplied ferrite core (small)

to the connecting cables.

Keep the ferrite core away from the SDI

module by fastening the connecting

cables with the cable clamp attached to

the SDI module.

Connecting

cables

Ground wires

Ferrite core (small)

Continue

Installation

5(for monitors except PVM-20S1WE/

20S1WU/20S1WA)

Connect the 12-pin connector of the SDI

module to the CN8 terminal (white) of

the BB board, and connect the 6-pin

connector of the SDI module to the

CN607 terminal (white) on the power

board.

CN607

(white)

6-pin

connector

CN8 (white) 12-pin

connector

Fasten the

cables from the

SDI module

with the cable

clamp.

7Connect the SDI module and the supplied

BB board to the monitor board.

Note

Take care not to touch the pins of the

terminals.

1Connect the connector of the supplied

3-pin connecting cable to the CN10

terminal (white) on the BB board.

2Connect the connector of the supplied

ground wire (for the BB board) to the

TP310 terminal on the BB board.

3Connect the CN9 terminal (grey) on the

BB board to the CN303 terminal (grey)

on the monitor board.

4Connect the 3-pin connecting cable

(type B) to the CN505 terminal on the

monitor board.

Leave the ground wire from the BB board

as it is. It will be connected later, together

with the ground wires for the SDI

module.

BB board

CN10 (white) 3-pin connecting cable

(type B)

CN9 (grey) on the

BB board

3-pin connecting cable

(type B)

CN303 (grey)

Ground wire

TP310

CN505

5(for PVM-20S1WA)

1 Open the D board to the right.

6-pin

connector

CN5104

(black)

D board

2 Connect the 12-pin connector of the

SDI module to the CN8 terminal

(white) of the BB board, and connect

the 6-pin connector of the SDI

module to the CN5104 terminal

(black) on the D board.

5(for PVM-20S1WE/20S1WU)

Connect the 12-pin connector of the SDI

module to the CN8 terminal (white) of

the BB board, and connect the 6-pin

connector of the SDI module to the

CN5104 terminal (black) on the D

board.

6-pin

connector

CN5104

(black)

Continue

Installation

For 20-inch monitors except PVM-

20S1WE/20S1WU/20S1WA

1Fasten the 2 cables from the SDI

module to the monitor with the

installed cable clamps.

2Fasten the monitor cable (connected to

the CN401 terminal) and the cable from

the SDI module (connected to the CN8

terminal on the BB board) with the

supplied cable clamp (black).

Push the SDI module forwards (to

the display side), and fasten it

with screws.

8Install the SDI module in the monitor.

For 14-inch monitors

1Remove the cable clamp from the

monitor and then the monitor cable.

2Attach the supplied holders (white).

Holder

3Fasten the 2 cables from the SDI

module with the attached holders from

4Fasten the monitor cable (connected to

the CN401 terminal) and the cable from

the SDI module (connected to the CN8

terminal on the BB board) with the

supplied cable clamp (black).

Pull the SDI module

back (to the connector

side), and fasten it with

screws.

Cables

D board

For PVM-20S1WA

1Fasten the cables to the monitor with

the installed cable clamp.

2Close the D board.

3Install the supplied cable clamp (ø11)

and wind the cable connected to the D

board to the supplied ferrite core

(large) by two turns and fasten the

cable with the cable clamp.

The installation method is the same as

that in steps 2and 3for the PVM-

20S1WE/20S1WU on the left column.

Cable clamp (ø11)

Ferrite core

(large)

Wind by

two turns.

For PVM-20S1WE/20S1WU

1Fasten the cables to the monitor with

the installed cable clamp.

2Install the supplied cable clamp (ø11) .

3Wind the cable connected to the D

board to the supplied ferrite core

(large) by two turns and fasten the

cable with the cable clamp.

Continue

(Only for monitors except PVM-20S1WE/

20S1WU/20S1WA)

Fasten the cable connected to the CN607

terminal on the power board.

Make sure that the cable does not loosen, and

fasten it with the cable clamps installed on

the monitor.

For 14-inch monitors

PVM-14M2E

PVM-14M4E

PVM-14M2A

PVM-14M4A

PVM-14M2U

PVM-14M4U

PVM-14M4B

Installation

9Connect the two ground wires attached to

the SDI module and the ground wire from

the BB board together to the ground plate

on the connector panel of the monitor

using the supplied +PS 4 ×8 screw.

Note

Position the ground wire for the BB board as

near as possible to the connecting panel of

the monitor. Then, fasten it using the cable

clamp, together with the cable connecting

between the CN306 terminal on the Q board

and the CN301 on the A board, and the cable

between the CN401 terminal on the A board

and the CN701 on the C board.

PVM-14M2U/14M2E/

14M2A Other monitors

Screw +PS 4 ×8 Screw +PS 4 ×8

Ground

wires for

the SDI

module

Ground

wires for

the SDI

module

Ground

wire for

the BB

board

Ground

wire for

the BB

board

Other manuals for BKM-101C

This manual suits for next models

Table of contents

Other Sony Monitor manuals

Sony

Sony LMD2451MD User manual

Sony

Sony TRIMASTER EL PVM-A250 User manual

Sony

Sony BVM-F250 User manual

Sony

Sony BVM-E251 User manual

Sony

Sony LMD-170W User manual

Sony

Sony LMD-2451MT User manual

Sony

Sony SDM-X52 - DELUXEPRO - 15" LCD Monitor User manual

Sony

Sony LMD-1530MD User manual

Sony

Sony FD Trinitron CPD-E100P User manual

Sony

Sony Trinitron PVM-14L3 User manual

Sony

Sony LUMA LMD-1410 User manual

Sony

Sony CPD-1730 User manual

Sony

Sony BRAVIA FW-85BZ35F User manual

Sony

Sony BRAVIA FW-43BZ35F User manual

Sony

Sony PlasmaPro FWD-42PV1 User manual

Sony

Sony LUMA LMD-4420 User manual

Sony

Sony TRINITRON BVM-20F1U User manual

Sony

Sony GDM-5403 User manual

Sony

Sony SDM-U27M90 Owner's manual

Sony

Sony GDM-20D10-15 User manual

Sony

Sony Trinitron PVM-1271Q User manual

Sony

Sony BVM-E250 User manual

Sony

Sony LMD1751WCC User manual

Sony

Sony LMD-1530MD User manual

Popular Monitor manuals by other brands

Linear Acoustic

Linear Acoustic LQ-1000 user guide

AOC

AOC I2579V user manual

Gateway

Gateway FPD1520 user guide

Furuno

Furuno Mu 120c Operator's manual

Asus

Asus VB171D - 17" LCD Monitor Service manual

Dell

Dell S2230MX Setting up

Philips

Philips 107C64 user manual

Dell

Dell S2409WFP user guide

EverFocus

EverFocus EN-7517E instruction manual

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Service manual

Dell

Dell Precision 7680 Connection guide

LG 50PM1M - - 50" Plasma Panel Service manual

Bosch

Bosch DDU 9 manual

Acer

Acer A231HL user manual

Philips

Philips 86BDL4152T user manual

NEC

NEC AccuSync LCD5V user manual

Emay

Emay SleepO2 user manual

IBM

IBM 6360 Product support manual