Sony BDX-E1000 User manual

MPEG ENCODER UNIT

BDX-E1000

AUDIO INPUT BOARD

BDKP-E1002

4:2:2 PROFILE UPGRADE BOARD

BDKP-E1003

SCRAMBLER BOARD

BDKP-E1004

SCRAMBLER BOARD

BDKP-E1005

INSTALLATION MANUAL

1st Edition (Revised 4)

BDX-E1000

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

DieAnleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt dieAngaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

BDX-E1000 Serial No. 10001 and Higher

BDKP-E1002 Serial No. 10001 and Higher

BDKP-E1003 Serial No. 10001 and Higher

BDKP-E1004 Serial No. 10001 and Higher

BDKP-E1005 Serial No. 10001 and Higher

1 (P)

For the U.S.A.

Attention-when the product is installed in Rack:

(For BDX-E1000)

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

BDX-E1000

1 (E)

BDX-E1000

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 3 (E)

Related manuals................................................................................................... 3 (E)

Contents ............................................................................................................... 3 (E)

Trademark............................................................................................................ 3 (E)

1. Installation

1-1. Installation Environment.......................................................................1-1 (E)

1-2. Power Supply ........................................................................................1-1 (E)

1-2-1. Power Specifications ............................................................1-1 (E)

1-2-2. Power Cord...........................................................................1-1 (E)

1-3. External Dimensions .............................................................................1-2 (E)

1-4. Rack Mounting......................................................................................1-2 (E)

1-5. Matching Connectors and Cables..........................................................1-5 (E)

1-6. Input and Output Signal of Connector ..................................................1-6 (E)

1-7. Internal Switches and Indicators ...........................................................1-8 (E)

1-7-1. APR-25 Board ......................................................................1-8 (E)

1-7-2. ENC-40 Board......................................................................1-9 (E)

1-7-3. SY-240 Board.....................................................................1-10 (E)

1-7-4. VPR-33 Board ....................................................................1-12 (E)

1-7-5. IO-158 Board .....................................................................1-13 (E)

1-8. Setting of Resume Function ................................................................1-13 (E)

1-9. Setting for Color Frame Information Transmission............................1-14 (E)

2. Installation of Optional Boards

2-1. General Information for Installation .....................................................2-1 (E)

2-2. BDKP-E1002 Installation .....................................................................2-2 (E)

2-3. BDKP-E1003 Installation .....................................................................2-4 (E)

2-4. BDKP-E1004/E1005 Installation..........................................................2-5 (E)

3. Service Overview

3-1. Cleaning ................................................................................................3-1 (E)

3-2. Periodic Replacement............................................................................3-2 (E)

3-3. ISR (Interactive Status Reporting) ........................................................3-3 (E)

3-3-1. ISR Functions Overview ......................................................3-3 (E)

3-3-2. Usage of ISR Functions .......................................................3-3 (E)

3-3-3. Error Messages.....................................................................3-6 (E)

3 (E)

BDX-E1000

Purpose of this manual This manual is the installation manual of the BDX-E1000 MPEG Encoder Unit and

the following optional boards.

.Audio Input Board BDKP-E1002

.4:2:2 Profile Upgrade Board BDKP-E1003

.Scrambler Board BDKP-E1004

.Scrambler Board BDKP-E1005

This manual is intended for use by trained system and service engineers, and

describes information regarding installation.

Related manuals Besides this Installation Manual, the following manuals are available for the BDX-

E1000.

.Operation Manual (Supplied with the BDX-E1000)

This manual explains the overview of the BDX-E1000, and the system configura-

tion examples.

.Maintenance Manual (Not supplied with the BDX-E1000)

This manual describes information that premise the service based on parts replace-

ment (adjustments, board layouts, schematic diagrams, parts list, etc.) and infor-

mation that premise the service based on block and board replacement.

If this manual is required, contact your local Sony Sales Office/Service Center.

Contents The following is a summary of all the sections for understanding the contents of this

manual.

Section 1 Installation

Explains the operating environment, the connector information for peripheral

equipment connections and the switches on the board for setup.

Section 2 Installation of Optional Boards

Explains how to install the optional boards.

Section 3 Service Overview

Explains the periodical replacement parts and summary of ISR.

Trademark

.Ethernet is a registered trademark of Xerox Corporation.

Manual Structure

1-1 (E)

BDX-E1000

Section 1

Installation

1-1. Installation Environment

1. Do not install the BDX-E1000 in the following

locations.

• Areas where the unit will be exposed to direct sun

light or any other strong lights.

• Dusty areas or areas where it is subject to vibration.

• Areas with strong electric or magnetic fields.

• Areas near heat sources.

• Areas where is subjected to electricity noise.

• Areas where is subjected to static electricity noise.

2. To prevent the temperature rise inside the BDX-

E1000, pay careful attention to circulation of air in the

place where the BDX-E1000 is installed.

The rear side of the BDX-E1000 should be at least

20 cm away from walls for ventilation and

maintenance.

Do not block the ventilation holes.

If the ventilation holes are blocked, the temperature inside

the BDX-E1000 getting rise. This may cause a fire.

1-2. Power Supply

1-2-1. Power Specifications

Power requirements : 100 to 240 V AC

50/60 Hz

Current consumption : maximum 2.0 A (at 100 V)

maximum 1.0 A (at 240 V)

A switching regulator is used for the power supply of the

BDX-E1000. The voltage within the range of 100 V to

240 V can be used without changing the supply voltage.

As the inrush current at turn-on is maximum 20 A (at

100 V)/maximum 40 A (at 240 V), the capacity of the AC

power must be adequate with the inrush current of

maximum 20 A (at 100 V)/maximum 40 A (at 240 V).

If the capacity of the AC power is not the adequately large,

the breaker of the AC power at the supply side will operate

or the BDX-E1000 will abnormal operate.

1-2-2. Power Cord

To avoid a fire or an electric shock, be sure to use the

designated power cord.

And do not damage to the power cord.

For the customer outside of the area as shown above or in a

part of Europe, the above-mentioned power cords con not

be used.

Use the power cord that is applicable to the places in the

world.

1 2

Power cord for the customer in the U.S.A. and Canada.

1Power cord set !1-557-377-11

2Plug holder (Black) 2-990-242-01

Power cord for the customer in the United Kingdom.

1DK-2401 (UK) (approx. 2.4 m)

2Plug holder (Black) 2-990-242-01

Plug holder is included in DK-2401 (UK).

Power cord for the customer in Europe except the

United Kingdom.

1DK-2401 (AE) (approx. 2.4 m)

2Plug holder (Brown) 3-613-640-01

Plug holder is included in DK-2401 (AE).

AC inlet

1-2 (E) BDX-E1000

1-3. External Dimensions

1-4. Rack Mounting

The BDX-E1000 can be mounted in a 19-inch standard rack.

• If the BDX-E1000 or the peripheral equipment is mounted in a 19-inch standard rack, it is recommend-

ed to install a ventilation fan to prevent a temperature rise in the rack.

Make sure that all the units in the rack should be operated within the temperature range of 5°C to 40°C.

• Connect the enough long cables on the rear panel, considering that the BDX-E1000 is pulled out.

• An installation manual is supplied with the RMM-30 rack mount rail. However follow the instructions

in this manual. Because the rack mounting procedures of the BDX-E1000 are different from the

procedures explained in RMM-30 installation manual.

• Be sure to fix the rack to the floor with bolts.

This will prevent the rack from falling when the unit is pulled out from the rack.

1-3. External Dimensions

1-4. Rack Mounting

894

892 475

424

450

304.883.7

57.2

132.4 (3U)14.5

254

101.6

482

465

424

(Front view) (Right side view)

(Top view)

Front panel

Unit : mm

Mass : 14.5 kg

Other manuals for BDX-E1000

This manual suits for next models

Table of contents

Popular Media Converter manuals by other brands

SoundTraxx

SoundTraxx Blunami BLU-2200 user guide

SPROLINK

SPROLINK VA1 user manual

Acclaim Lighting

Acclaim Lighting DDC-1-AC user guide

Nikon

Nikon AF-S TC-20E III user manual

Axis

Axis AXIS Q7406 user manual

Omega

Omega TAC80B-J instruction sheet

Zoom

Zoom Thunderbolt TAC-2R Operation manual

OST

OST iConverter 10/100M quick start guide

Vertiv

Vertiv Netsure user manual

birddog

birddog MINI user guide

Roland

Roland GI-10 owner's manual

Wallenstein

Wallenstein WX310 Operator's manual

Pace

Pace MSS 200-1 Service manual

Solar Converters

Solar Converters EQ 12/24-50 manual

CYP

CYP EL-7400V Operation manual

TIE

TIE MIDI 1i1o user manual

DCS

DCS Vivaldi Upsampler user manual

Westermo

Westermo MCW-211 SERIES user guide