Sony HKSR-9003 User manual
RGB 4:4:4 PROCESSOR BOARD
HKSR-9003
INSTALLATION MANUAL
1st Edition
!警告
このマニュアルは，サービス専用です。
お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。
設置や保守，点検，修理などを行う前に，カムコーダー本体に付属している下記マニュアルの「安
全のために」を必ずお読みください。
. SRW-9000
メンテナンスマニュアルおよびオペレーションマニュアル
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
1-1 (E)
HKSR-9003
Section 1
Installation
Purpose of this manual
This manual is an installation manual of RGB 4:4:4 Pro-
cessor Board HKSR-9003.
Intended for use by system and service engineers, this
manual describes information on installation of
HKSR-9003.
Related manual
Besides this installation manual, the following manual is
available for HKSR-9003.
.SRW-9000 Maintenance Manual (available on request)
This manual describes information on the maintenance
and component-based service of the unit.
If you need this manual, please contact your local Sony
Sales Office/Service Center.
1-1. Specifications
General
Dimensions (W/H/D including projections)
:
130 x102 x11 mm
Mass (heatsink +board)
: Approx. 95 g
Power voltages and power consumption: 5.5 W
1-2. Overview of Installation
Components
.PR-318 board
.Heatsink (PR) assembly
.Screw B2 x4 (3)
.Installation Manual
.Installation Guide
Applicable model
SRW-9000
Installation of HKSR-9003
Attach and adjust the unit properly following the proce-
dures in Section 1-3 and later.
Indicator on PR-318 board
PR-318 BOARD (SIDE A)
LED. No. Color Description Normal state at
Power ON
D100 Green Indicates that PR-318
board is running
OFF
D100
A
1
2
3
4
5
BCD
1-2 (E) HKSR-9003
1-3. Installation Procedures
m
.Power off the unit and disconnect the power
cord or battery beforehand to avoid damage to
the circuit of the unit.
.Carry out the work on a protective sheet to
avoid scratches on the cabinet.
1. Loosen the six screws with stopper to detach
the top panel.
2. Disconnect the harness from the connector
CN103 on the SMB-26 board.
3. Loosen the four screws with stopper to detach
the battery panel.
4. Disconnect the harnesses from the connector
CN4 on the CR-51 board and the connector
CN10 on the RE-244 board.
5. Remove the four screws to detach the board
retainer in the arrow direction.
n
When installing the board retainer, insert it
into the two slits of the chassis and secure it
with the four screws.
6. Detach the board spacer.
7. Disconnect the harness (AXM-VPR) from the
connector CN3 on the AXM-37 board.
CN103
CN4
CN10
Screws with stopper
Screws with stopper
Screws with stopper
Battery panel
Top panel
PSW2.6 x5
PSW2.6 x5
Board retainer
CN3
Board spacer
Harness (AXM-VPR)
Slits
1-3 (E)
HKSR-9003
8. Insert the blade of a screwdriver as shown in
the figure and push the screwdriver in the
arrow direction to disconnect the VPR-101
board from the MB-1106 board.
n
The board name and a number of board
removing order are stamped on each board
bracket.
Example) To remove the SS-103 board
Remove the VPR, RE, and SS
boards in this order.
The VDA-69 board need not be
removed.
VPR-101 board
SS-103 board
RE-244 board
VPR-101 board
VDA-69 board
Board name
Number of board
removing order
Screwdriver
1-4 (E) HKSR-9003
VPR-101 board
CN600
Harness
(AXM-VPR)
30 mm
9. Draw the VPR-101 board approximately 30
mm out of the unit, and disconnect the har-
ness (AXM-VPR) from the connector CN600.
10. Loosen the screw with stopper to detach the
cable stopper (30P).
11. Disconnect the fine-wire coaxial cable from
the connector CN2100 on the VPR-101 board
using the cable stopper (30P). (Refer to
Section 1-4-1.)
m
.Disconnect the fine-wire coaxial cable
using the procedure described in Section
1-4-1.
.Never pull the fine-wire coaxial cable.
12. Loosen the screw with stopper to detach the
cable stopper (BNC).
13. Disconnect the fine-wire coaxial cable from
the connector CN2101 on the VPR-101 board
using the cable stopper (30P). (Refer to
Section 1-4-1.)
14. Loosen the screw with stopper to detach the
cable stopper (BNC-2).
15. When the HKSR-9001 is installed in the unit,
disconnect the three coaxial cables from the
connectors CN1012, CN1010, and CN1011
on the TR-139 board using the cable stopper
(BNC). (Refer to Section 1-4-2.)
16. Remove the VPR-101 board from the unit.
n
Be very careful so that the harnesses and
cables are not caught.
Installed in HKSR-9001
TR-139 board
CN1011
coaxial cable
CN1010
CN1012
Blue
Gray
Red
CN2101
Gold
Gold
CN2100
Fine-wire
coaxial cables
Screws with stopper
Screw with stopper
Cable stopper
(BNC)
Cable stopper
(BNC-2)
Coaxial cables
Bainding
bands
Cable stopper (30P)
1-5 (E)
HKSR-9003
17. Remove the two screws to detach the dummy
plate (PR).
18. Remove the two nylon rivets securing the
heatsink (PR) assembly to the PR-318 board.
19. Check that radiation sheets (9 x12) are
attached to IC1000, IC1001, IC1003, IC1200,
and IC1202 on the PR-318 board.
20. Connect the connector CN100 on the PR-318
board to the connector CN2201 on the
VPR-101 board.
21. Install the heatsink (PR) assembly with the
supplied three screws.
B2 x4
VPR-101 board
Dummy plate (PR)
Heatsink (PR) assembly
VPR-101 board
CN100
PR-318 board
B2 x4
B2 x4
Radiation sheet (9 x12)
IC1200
IC1000
IC1202 IC1003
IC1001
CN2201
1-6 (E) HKSR-9003
B
G
R
Cable stopper (BNC-2)
A
Screw with stopper
Coaxial cables
Coaxial cable
Blue
Gray
Red
TR-139 board
Heatsink (TR)
assembly
22. Insert the VPR-101 board along the rails
shown in the figure to the position where the
VPR-101 board is drawn out of the unit about
30 mm.
n
Slowly insert the VPR-101 board straight.
23. When the HKSR-9001 is installed in the unit,
connect the three coaxial cables disconnected
in step 15 to the connectors CN1012,
CN1010, and CN1011 on the TR-139 board.
(Refer to Section 1-4-2.)
n
Match the colors of the coaxial cables with
the silk print R (Red), G (Gray), and B (Blue)
on the TR-139 board.
24. Arrange the three coaxial cables as shown in
the figure.
25. Hook portion A (three locations) of the cable
stopper (BNC-2) to the edge of the heatsink
(TR) assembly, and secure the cable stopper
with a screw with stopper.
SS-103 board
RE-244 board
VPR-101 board
VDA-69 board
VDA-69 board
VPR-101 board
RE-244 board
SS-103 board
1-7 (E)
HKSR-9003
CN2100
CN2101
Hook
Hook
Gold
Fine-wire
coaxial cables
A
Cable stopper (BNC)
Cable stopper
(BNC)
A
Do not put on the connector.
Pushing direction (B)
Arrow B view Arrow B view
A
Fine-wire coaxial cable
CN2101
Screw with
stopper
Screw with
stopper
Cable stopper
(BNC)
Cable stopper
(30P)
A
OK NG
Cable stopper
(BNC)
Gold
A
A
A
A
26. Connect the fine-wire coaxial cable discon-
nected in step 13 to the connector CN2101 on
the VPR-101 board. (Refer to Section 1-4-1.)
n
Connect the fine-wire coaxial cable in the
way described in Section 1-4-1.
27. Hook the cable stopper (BNC) to the hook of
the VPR bracket.
28. While pushing the cable stopper (BNC) in the
arrow direction so that portion A of the cable
stopper is not put on the connector CN2101,
secure the cable stopper (BNC) with a screw
with stopper.
29. Connect the fine-wire coaxial cable discon-
nected in step 11 to the connector CN2100 on
the VPR-101 board. (Refer to Section 1-4-1.)
30. Hook the cable stopper (30P) to the hook of
the VPR bracket.
31. While pushing the cable stopper (30P) in the
arrow direction so that portion A of the cable
stopper is not put on the connector CN2100,
secure the cable stopper (30P) with a screw
with stopper.
1-8 (E) HKSR-9003
CN600
Cable stopper (30P)
Cable stopper (BNC)
Harness (AXM-VPR)
Two coaxial cables
(B, G)
Do not bend the
coaxial cable sharply.
Harness guard A coaxial cable
(R)
Harness clamp
Avoid the connector.
32. Connect the harness (AXM-VPR) to the
connector CN600 on the VPR-101 board.
33. Arrange the harness (AXM-VPR) inside the
hooks of the two cable stoppers as shown in
the figure.
34. Push the VPR bracket to connect the
VPR-101 board to the MB-1106 board.
35. Arrange the harness and coaxial cables as
shown in the figure.
Clamp all the slacks of the coaxial cables
with the harness clamp as shown in the figure.
36. Install the removed parts by reversing steps 1
to 7.
37. Check that the HKSR-9003 has been recog-
nized with the SYSTEM menu. (Refer to Sec-
tion 1-5.)
Table of contents
Other Sony Computer Hardware manuals
Sony
Sony MVS-6530 User manual
Sony
Sony ESBK-7051 User manual
Sony
Sony PCWA-C150S - Wireless Lan Pc Card User manual
Sony
Sony BKM-101C User manual
Sony
Sony PCWA-C700 - Wireless Lan Dual Pc Card User manual
Sony
Sony BPU4000 User manual
Sony
Sony BKPF-L752 User manual
Sony
Sony CMOS CXP854P60 User manual
Sony
Sony PCWA-C800S Read This First Instruction sheet
Sony
Sony PCWA-C800S Read This First Quick start guide
Sony
Sony HKSR-5804 User manual
Sony
Sony PDBK-201 Quick start guide
Sony
Sony BPU-4500A User manual
Sony
Sony DP-IF5100 User manual
Sony
Sony PCWA-C700 - Wireless Lan Dual Pc Card Datasheet
Sony
Sony HR-GP5 User manual
Sony
Sony PCWA-C700 - Wireless Lan Dual Pc Card User manual
Sony
Sony PCWA-C100 User manual
Sony
Sony SDP-EP90ES User manual
Sony
Sony HFBK-SD1 User manual
Popular Computer Hardware manuals by other brands
EMC2
EMC2 VNX Series Hardware Information Guide
Panasonic
Panasonic DV0PM20105 Operation manual
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 user manual
Gigabyte
Gigabyte B660M DS3H AX DDR4 user manual
Raidon
Raidon iT2300 Quick installation guide
National Instruments
National Instruments PXI-8186 user manual
