Sonance BPS6 TL User manual
Determine the location of the mounting platform
and subwoofer. Ensure there is adequate space to
accommodate the subwoofer and port tube within the
2 x 4 stud bay or joist, allowing 15” from the front edge
of the BPS6 TL to the center of connector. (See Figure 1).
Box Contents
(1) Quickstart Guide
(1) Bandpass Subwoofer with port tube
(1) Cardboard mounting template
MOUNTING SCREWS & WASHERS:
(4) 5/16” x 3” lag screws
(4) 5/16” washers
BPS6 TL QUICKSTART GUIDE FOR USE WITH
ARCHITECTURAL SERIES BANDPASS CONNECTORS
BANDPASS SUBWOOFER THINLINE (AS)
Place the subwoofer mounting template on the side of a
2 x 4 stud or joist and drill four 1/4” (6mm) holes through
the stud at the locations shown on the mounting template.
(See Figure 2).
Hold the side of the BPS6 TL Subwoofer with the rubber
damping pad up against the side of the stud or joist and
install the four lag screws and washers to secure the
BPS6 TL Subwoofer in place. (See Figure 3).
1
15” (381mm)
BPS6 TL
Architectural Series
mounting platform
Port Tube
NOTE: IF IT IS NOT POSSIBLE TO LOCATE THE BPS6 TL SUBWOOFER
15” AWAY FROM THE 90 DEGREE CONNECTOR OF THE MOUNTING
PLATFORM, EXTRA HOSE MATERIAL (UP TO 3”) MAY BE REMOVED.
WHILE IT IS OKAY TO SHORTEN THE HOSE, NEVER EXTEND THE
HOSE LENGTH.
NOTE: DRILLING FROM THE INSIDE OF THE STUD BAY IS
RECOMMENDED TO ENSURE THAT THE HOLE LOCATIONS
MATCH THE SUBWOOFER SCREW LOCATIONS. (SEE FIGURE 2)
NOTE: BE SURE THAT THE SUBWOOFER TEMPLATE IS FLUSH
WITH THE EDGE OF THE STUD OR SLIGHTLY RECESSED.
Prepare to attach the mounting platform to the stud
or joist. Position the platform with the 90 degree
connector pointed in the direction of the BPS6 TL
port tube. (See Figure 4).
2
3
4
Figure 1
Figure 2
Figure 3
Figure 4
Template
©2017 Sonance. All rights reserved. Sonance and Architectural Series are registered trademarks of Dana Innovations. Due to continuous product improvement,
all features and specications are subject to change without notice. For the latest Sonance product specication information visit our website: www.sonance.com
SONANCE • 991 Calle Amanecer • San Clemente, CA 92673 USA • PHONE: (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (949) 492-7777 10.24.17
The BPS6 TL ships with a foam plug and tether inserted
into the end of the port tube; remove and discard.
Guide the port tube onto the 90 degree connector so
the tube is positioned snugly in place. Tighten the clamp
ring to secure the port tube.
(See Figure 5).
Attach the mounting platform to the stud or joist.
For mounting platform installation details visit
www.sonance.com/in-wall-in-ceiling/
architectural-series/bps6-tl.
BPS6 TL QUICKSTART GUIDE FOR USE WITH ARCHITECTURAL SERIES BANDPASS CONNECTORS
Attach the four conductor speaker wire to the input
terminals; positive wires to red terminals and negative
wires to black terminals. Run a signal test using an
amplied program material for at least 60 seconds.
Secure the speaker wire to the zip tie attached to the
subwoofer cabinet to prevent accidental removal.
(See Figure 6).
For more eManuals and diagrams visit
www.sonance.com/in-wall-in-ceiling/bps6-tl
33-7939
5
LEFT
BPS6TL
RIGHT
MADE IN CHINA
6
Included
zip tie
for wire
Figure 5
Figure 6
Table of contents
Other Sonance Subwoofer manuals
Sonance
Sonance Sonance Landscape Series LS12ESUB User manual
Sonance
Sonance Cinema Series SUB 10-150 User manual
Sonance
Sonance BPS6 User manual
Sonance
Sonance LS47SAT User manual
Sonance
Sonance A800D User manual
Sonance
Sonance BPS8 User manual
Sonance
Sonance BPS-1 User manual
Sonance
Sonance ThinLIne Series User manual
Sonance
Sonance BPS6 User manual
Sonance
Sonance D8 User manual
Sonance
Sonance VP10SUB User manual
Sonance
Sonance LS47SAT User manual
Sonance
Sonance XBW User manual
Sonance
Sonance Cinema Series SUB 10-150 User manual
Sonance
Sonance Virtuoso A800D User manual
Sonance
Sonance i12 User manual
Sonance
Sonance Cinema Series CINEMA SUB User manual
Sonance
Sonance VIRTUOSO A800D User manual
Sonance
Sonance Landscape Series User manual
Sonance
Sonance RK10W User manual
