SOLAREVER SE-BAT SYS-HV User manual

SE-BAT Lithium-ion Battery

User Manual

50Ah

The copyright of this manual belongs to Solarever Tecnologia de America S.A.de C.V. Any

corporation or individual should not plagiarize, partially or fully copy it (including software, etc.),

and reproduction or distribution in any form or by any means shall not be allowed. All rights

reserved. Solarever Tecnologia de America S.A.de C.V. reserves the right of nal interpretation. The

information contained herein is subject to change without notice.

www.solarever.com.mx

Solarever Tecnologia de America S.A.de C.V.

Autopista Mexico-Queretaro KM 71.9, S/N Noxtongo Tepeji del

Rio de Ocampo C.P. 42885, Hidalgo Mexico

Tel.: +55 4364 0437

E-mail: contacto@solarever.com.mx 614.00748.00

CONTENTS

1 NOTE ON THIS MANUAL..............................................................................................................................................1

1.1 SCOPE OF VALIDITY............................................................................................................................................1

1.2 TARGET GROUP......................................................................................................................................................1

1.3 SYMBOLS USED.....................................................................................................................................................1

2 SAFETY.......................................................................................................................................................................................2

2.1 SAFETY INSTRUCTIONS..................................................................................................................................2

2.1.1 GENERAL SAFETY PRECAUTIONS..................................................................................................2

2.1.2 EXPLANATION OF SYMBOLS.............................................................................................................3

2.2 RESPONSE TO EMERGENCY SITUATIONS..........................................................................................5

2.2.1 LEAKING BATTERIES..................................................................................................................................5

2.2.2 FIRE........................................................................................................................................................................5

2.2.3 WET BATTERIES AND DAMAGED BATTERIES........................................................................5

2.3 QUALIFIED INSTALLER.....................................................................................................................................6

3 PRODUCT INTRODUCTION......................................................................................................................................7

3.1 PRODUCT OVERVIEW.......................................................................................................................................7

3.1.1 DIMENSION AND WEIGHT..................................................................................................................7

3.1.2 APPEARANCE................................................................................................................................................8

3.2 BASIC FEATURES................................................................................................................................................10

3.2.1 FEATURES......................................................................................................................................................10

3.2.2 CERTIFICATIONS......................................................................................................................................10

3.3 SPECIFICATIONS.................................................................................................................................................11

3.3.1 SE-BAT SYS-HV CONFIGURATION LIST.....................................................................................11

3.3.2 PERFORMANCE.........................................................................................................................................11

4 INSTALLATION..................................................................................................................................................................12

4.1 INSTALLATION PREREQUISITES..............................................................................................................12

4.2 SAFETY GEAR.......................................................................................................................................................12

4.3 TOOLS.......................................................................................................................................................................13

4.4 INSTALLATION.....................................................................................................................................................13

4.4.1 CHECK FOR TRANSPORT DAMAGE..........................................................................................13

4.4.2 UNPACKING.................................................................................................................................................13

4.4.3 ACCESSORIES.............................................................................................................................................14

4.4.4 BATTERY INSTALLATION STEPS....................................................................................................16

1 Note on this Manual

1.1 Scope of Validity

This manual is an integral part of SE-BAT Series. It describes the assembly,

installation, commissioning, maintenance and failure of the product. Please read

it carefully before operating.

SE-BAT SYS-HV

1.2 Target Group

This manual is for qualied ele tricians. The tasks described in this manual may

only be performed by qualied ele tricians.

1.3 Symbols Used

The following types of safety instructions and general information appear in this

document described as below:

DANGER!

“DANGER” indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING!

“WARNING” indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTIOIN!

“CAUTION” indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTE!

“NOTE” provides tips that are valuable for the optimal operation of

your product.

4.5 OVERALL INSTALLATION.....................................................................................................................................18

4.5.1 CABLE CONNECTION...................................................................................................................................20

4.5.2 CONNECTING POWER CABLES............................................................................................................22

4.5.3 CONNECTING POWER LINES.................................................................................................................26

4.5.4 CONNECTING CAN COMMUNICATION CABLE.......................................................................27

4.5.5 CONNECTING RS485 COMMUNICATION CABLE...................................................................28

4.5.6 CONNECTING GROUND WIRE..............................................................................................................29

4.6 OVERVIEW OF INSTALLATION..........................................................................................................................31

5 COMMISSIONING...................................................................................................................................................................32

5.1 CONFIGURING BATTERY SYSTEM....................................................................................................................32

5.2 COMMISSIONING.........................................................................................................................................................33

5.3 STATUS INDICATORS...............................................................................................................................................35

5.3.1 BMS ............................................................................................................................................................................35

5.3.2 BATTERY PACK....................................................................................................................................................36

5.4 SHUTTING DOWN SE-BAT SYSTEM.............................................................................................................36

6 TROUBLESHOOTING............................................................................................................................................................37

6.1 TROUBLE SHOOTING.............................................................................................................................................37

7 DECOMMISSIONING............................................................................................................................................................40

7.1 DISMANTLING THE BATTERY............................................................................................................................40

7.2 PACKAGING....................................................................................................................................................................40

SE-BAT-MA H 5.8

NOTE: There are 4 models for SE-BAT system, which includes BMS and battery

pack(s). Please refer to section 3.3.1 SE-BAT SYS-HV Conguration List on page 11

for detailed models.

SE-BAT PACK-HV

SE-BAT-SL H 5.8

8 MAINTENANCE AND WARRANTY.............................................................................................................................41

2 Safety

2.1 Safety Instructions

For safety reasons, installers are responsible for familiarizing themselves with the

contents of this manual and all warnings before performing installation.

2.1.1 General Safety Precautions

Observe the following precautions:

ŸRisks of explosion

–Do not subject the battery pack to strong impacts.

–Do not crush or puncture the battery pack.

–Do not dispose of the battery pack in a re.

ŸRisks of re

–Do not expose the battery pack to temperatures in excess of 13 .1℉/55°C.

–Do not place the battery pack near a heat source, such as a replace.

–Do not expose the battery pack to direct sunlight.

–Do not allow the battery connectors to touch conductive objects such as

wires.

ŸRisks of electric shock

–Do not disassemble the battery pack.

–Do not touch the battery pack with wet hands.

–Do not expose the battery pack to moisture or liquids.

–Keep the battery pack away from children and animals.

ŸRisks of damage to the battery pack

–Do not allow the battery pack to get in contact with liquids.

–Do not subject the battery pack to high pressures.

–Do not place any objects on top of the battery pack.

SE-BAT SYS-HV can be used only in the household energy eld. It is not allowed to

be used in other industries, such as the medical equipment and automotive

application.

WARNING!

Please don't crush or impact the battery, and always dispose it

according to the safety regulation.

2.1.2 Explanation of Symbols

This section gives an explanation of all the symbols shown on the SE-BAT system

and on the warning label.

CAUTION!

If the battery is not installed within one month after receiving the battery, the

battery must be charged till the SOC is more than 50% for maintenance.

Wear protecitve glasses

Observe enclosed documentation.

Keep the battery system away from open ames or i nition

sources.

Keep the battery system away from children.

Danger of high voltages.

Danger to life due to high voltages in the battery system!

Danger.

Risk of electric shock!

The battery pack may explode.

Symbol Explanation

The PV inverter is compliant with TUV

The battery system should be disposed of at a proper facility

for environmentally safe recycling.

The battery system should not be disposed together with the

household waste.

Disposal information can be found in the enclosed documentation.

2.2 Response to Emergency Situations

2.2.1 Leaking Batteries

If the battery leaks electrolyte which is corrosive, avoid contact with the leaking

liquid or gas. Direct contact may lead to skin irritation or chemical burns. If one is

exposed to the leaked substance, do these actions:

Accidental inhalation of harmful substances:Evacuate people from the

contaminated area , and seek medical attention immediately.

Eye contact: Rinse eyes with owing water or 15 minutes, and seek medical

attention immediately.

Dermal contact: Wash the aﬀected area thoroughly with soap and water, and

seek medical attention immediately.

Ingestion: Induce vomiting, and seek medical attention immediately.

2.2.2 Fire

In case of a re, make sure an ABC or carbon dioxide extinguisher is nearby.

WARNING!

The battery pack may catch re when heated above 150°C.302℉/

If a re breaks out where the battery pack is installed, do

these actions:

1. Extinguish the re before the batterry pack catches re;

2. If the battery pack has caught re, do not try to

extinguish the re. Evacuate people immediately.

WARNING!

If the battery pack catches re, it will produce noxious and poisonous gases.

Do not approach.

2.2.3 Wet Batteries and Damaged Batteries

If the battery pack is wet or submerged in water, do not try to access it.

If the battery pack seems to be damaged, they are not t or use and may pose a

danger to people or property.

Please pack the battery in its original container, and then return it to Solarever or

your distributor.

CAUTION!

CSA certied

CE mark.

The inverter complies with the requirements of the applicable

CE guildlines.

272687

Damaged batteries may leak electrolyte or produce ammable gas. If

you suspect such damage, immediately contact Solarever for advice

and information.

2.3 Qualied nstaller

WARNING!

All operations of SE-BAT SYS-HV relating to electrical connection and

installation must be carried out by qualied personne.

A skilled worker is dened as a trained and qualied electrician or installer who

has all of the following skills and experience:

ŸKnowledge of the functional principles and operation of on-grid systems

ŸKnowledge of the dangers and risks associated with installing and using

electrical devices and acceptable mitigation methods

ŸKnowledge of the installation of electrical devices

ŸKnowledge of and adherence to this manual and all safety precautions and

best practices

3 Product Introduction

3.1 Product Overview

For safety reasons, installers are responsible for familiarizing themselves with the

contents of this manual and all warnings before performing installation.

3.1.1 Demension and Weight

A battery management system (BMS) is any electronic system that manages a

rechargeable battery.

Battery pack is a type of electrical battery which can be charged, discharged into

a load.

A battery system includes BMS and battery pack(s).

SE-BAT-SL H 5.8

(Battery Pack)

SE-BAT-MA H 5.8

Length

Width

Height

Weight

SE-BAT-MA H 5.8 SE-BAT-SL H 5.8

3. Product Introduction

18.66 in/474.00 mm

7.60 in/193.00 mm

27.87 in/708.00 mm

159.2 lbs/72.2 kg

25.47 in/647.00 mm

151.0 lbs/68.5 kg

18.66 in/474.00 mm

7.60 in/193.00 mm

27.87 in/708.00 mm

25.47 in/647.00 mm

18.66 in/474.00 mm

7.60 in

193.00 mm

18.66 in/474.00 mm

7.60 in

193.00 mm

ŸSection view of SE-BAT-SL H 5.8

3. Product Introduction 3. Product Introduction

3.1.2 Appearance

ŸSection view of SE-BAT-MA H 5.8

Object Mark Description

Ⅰ

Ⅱ

Ⅲ

Ⅳ

BAT+/BAT-

CAN

GND

Charge/Discharge Connectors

CAN Connector

GND

Air Valve

Object Mark Description

Ⅰ'

Ⅱ'

Ⅲ'

Ⅳ'

Ⅴ'

XPLUG

RS485 I

GND

Ⅰ

Ⅱ Ⅲ

Ⅳ

Ⅴ Ⅵ

Ⅶ

ⅧPower Connector’ to YPLUG of upper battery pack

RS485 Connector to RS485 II of upper battery pack

GND

RS485 Connector to RS485 I of next battery pack

Power Connector’ to XPLUG of next battery pack, or

to “-” of the same pack

Air valve

BAT+BAT-

CAN

-YPLUG

RS485 II

Ⅲ

XPLUG

RS485 I

-YPLUG

RS485 II

Ⅰ'Ⅱ’'

Ⅲ’'Ⅳ’'

Ⅴ’'

Ⅵ’'Ⅶ'

Ⅷ’'Ⅳ'

Power Connector to “-” of upper battery pack

Power Connector to + of next battery pack, or to YPLUG

of the same pack

RS485 Connector to RS485 I of next battery pack

Power Button

DIP Switch

Circuit Breaker

Ⅴ

Ⅵ

Ⅶ

Ⅷ

Ⅸ

Ⅹ

YPLUG

RS485 II

POWER

DIP

ON/OFF

Power Connector’ to XPLUG of next battery pack,

or to “-” of the same pack

Power Connector to + of next battery pack, or to

YPLUG of the same pack

Ⅵ'

Ⅶ'

Ⅷ'

YPLUG

RS485 II

3.2 Basic Features

3.2.1 Features

The SE-BAT SYS-HV is one of the advanced energy storage systems on the market

today, incorporating state-of-the-art technology, high reliability, and convenient

control features shown as below:

Ÿ90% DOD

Ÿ99% Faradic charge eﬃciency

Ÿ95% Battery roundtrip eﬃciency

ŸCycle life > 6000 times

ŸSecondary Protection by hardware

ŸIP55 protection level

ŸSafety & Reliability

ŸSmall footprint

ŸFloor or wall mounting

3.2.2 Certications

3. Product Introduction 3. Product Introduction

10 11

SE-BAT system safety

Battery cell safety

UN number

Hazardous materials classication

UN transportation testing requirements

International protection marking

CE, FCC, RCM, TUV (IEC 62619), UL 1973

UL 1642

UN 3480

Class 9

UN 38.3

IP 55

3.3 Specications

3.3.1 SE-BAT SYS-HV Conguration List

3.3.2 Performance

Model Battery Pack Energy(kWh) Voltage (V)

No.

SE-BAT H 5.8

SE-BAT H 11.5

SE-BAT H 17.3

SE-BAT-MA H 5.8*1

SE-BAT-MA H 5.8*1+SE-BAT-SL H 5.8*1

SE-BAT-MA H 5.8*1+SE-BAT-SL H 5.8*2

5.8

11.5

17.3

100-131

200-262

300-393

SE-BAT-MA H 5.8 SE-BAT-SL H 5.8

Dimension (in/mm)

Weight (kg)

Nominal Voltage (V d.c.)

Operating Voltage (V d.c.):

Nominal Capacity (Ah)

Nominal Energy (kWh) :

Recommend Charge/Discharge Current (A d.c.):

Standard Power (kW)

Maximum Power (kW)

72.2

115.2

100-131

5.8

2.9

4.0

68.5

115.2

100-131

5.8

2.9

4.0

Altitude (m)

Faradic Charge Eﬃciency (25°C/77°F)

Battery Roundtrip Eﬃciency (C/3,25°C/77°F)

Expected Lifetime (25°C/77°F)

Cycle Life (90% DOD, 25°C/77°F)

Available Operating Temperature

Optimal Operating Temperature

Storage Temperature

Ingress Protection

≤2000

99%

95%

10 years

6000 cycles

IP55

Test conditions: 100% DOD, 0.5C charge & discharge @+25°C

Discharging: 41 /0 ~5 and /45-55 will be rating 32℉~℉°C °C 113℉~131℉°C

90% DOD; System usable energy may vary with inverter diﬀerent setting

Charging: 32℉~41℉/0°C~5°C and 104℉~122℉/40°C~50°C will be rating

Usable Energy (kWh) :

Max. Сharge/Discharge Current (A d.c.) :

5.2

32℉~131℉/0°C~55°C

59 ~95 15 ~35℉ ℉/ °C °C

-4℉~131℉/-20°C~55°C (3 months)

32℉~104℉/0°C~40°C (1 year)

18.66*7.60*27.87

474.00*193.00*708.00

18.66*7.60*25.47

474.00*193.00*647.00

4 Installation

4.1 Installation Prerequisites

Make sure that the installation location meets the following conditions:

ŸThe building is designed to withstand earthquakes

ŸThe location is far away from the sea, to avoid salt water and humidity

ŸThe oor is at and level

ŸThere are no ammable or explosive mateials nearby

ŸThe ambience is shady and cool, keep away from heat and avoid direct

sunlight.

ŸThe temperature and humidity stays at a constant level.

ŸThere is minimal dust and dirt in the area.

ŸThere is no corrosive gases present, including ammonia and acid vapor.

ŸThe ambient temperature is within the range from 32℉113℉45°C, and the /0°C to /

optimal ambient temperature is between ℉ ℉ .9/15°C and 95 /35°C

NOTE!

If the ambient temperature is outside the operating range, the battery pack

stops operating to protect itself. The optimal temperature range for the battery

pack to operate is 15°C to 35°C. Frequent exposure to harsh temperatures may

deteriorate the performance and lifetime of the battery pack.

4.2 Safety Gear

Installation and maintenance personnel must operate according to applicable

federal, state and local regulations as well as the industry standards regarding the

product installation personnel shall wear safety gears, etc. in order to avoid short

circuit and personal injury.

Insulated gloves Safety goggles Safety shoes

4. Installation

12 13

4. Installation

4.3 Tools

These tools are required to install the SE-BAT system.

Torque screw driver Phillips-screw driver Socket nut wrench

Phillips-head screw driver Flat-head screw driver Torque wrench

Tape measure Drill Pencil or Marker

4.4 Installation

4.4.1 Check for Transport Damage

Make sure the battery is intact during transportation. If there are some visible

damages, such as cracks, please contact your dealer immediately.

4.4.2 Unpacking

Unpacking the battery package by cutting the packing tape and make sure the

battery packs and the relevant items are complete. See package items on section

4.4.3, please check the packing list carefully, if there's any item missing, please

contact Solarever or your distributer directly.

CAUTION!

According to regional regulations, several people may be required for

moving equipment.

WARNING!

Please strictly follow the installation steps. Solarever will not answer for

any hurting or loss arising by incorrectly assembling and operation.

NOTE!

The SE-BAT battery pack is rated at IP55 and thus can be installed

outdoors as well as indoors. However, if installed outdoors, do not allow the

battery pack to be exposed to direct sunlight and moisture.

4. Installation 4. Installation

4.4.3 Accessories

The table below lists the number of each component.

SE-BAT-MA H 5.8:

Object

Description

Power line between Inverter and SE-BAT-MA H 5.8 (+) ( )6.56 ft/2.00 m)

Power line between Inverter and SE-BAT-MA H 5.8 (-) ( )6.56 ft/2.00 m

CAN communication cable ( )6.56 ft/2.00 m

Series-connected plug

Cover plate2

M4 screw

Cover plate2

Wall bracket

M5 screw

Expansion bolt

Ring terminal (for grounding)

Power cable disassembling tool

Grounding nut

Quantity

SE-BAT-SL H 5.8:

Quantity Object

Description

Power cable between battery packs ( )259.59 in/650.00 mm

Power cable’ between battery packs ( )259.59 in/650.00 mm

Rs485 communication cable ( )259.59 in/650.00 mm

Cover plate2

M4 screw

Cover plate2

Wall bracket

M5 screw

Expansion bolt

Ring terminal (for grounding)

Grounding nut

A(Red cable)B(Black cable) C

D(Black cable)

B1 C1

G1 H1F1

D1 E1

The table below lists the number of each component.

J1 K1

RS485cable*1

This manual suits for next models

Table of contents

Popular Batteries Pack manuals by other brands

Acumentrics

Acumentrics PACK-POWER SYSTEM Quick reference guide

ACDC Dynamics

ACDC Dynamics SPF12-50 user manual

Aegis

Aegis ABL-72020P user manual

Dyness

Dyness TowerESS user manual

Growatt

Growatt APX 5.0P-S0-US user manual

EGO

EGO BAX1300 Operator's manual

CyberPower

CyberPower BCA Series installation manual

Intermec

Intermec 700 Series quick start guide

Dometic

Dometic PLB40 operating manual

V-TAC

V-TAC VT-48280-W2 instruction manual

Valence

Valence RT user guide

Nikon

Nikon MB-D14 user manual

IOGear

IOGear GBP24V Series user manual

Inventus Power

Inventus Power PROTRXion S-12V100-TRX-HD user manual

Clas Ohlson

Clas Ohlson PW-290A quick start guide

EINHELL

EINHELL MULTI-Ah Power X-Change Plus Original operating instructions

Samsung

Samsung EB-U3300 quick start guide

ECTIVE

ECTIVE LC Series instruction manual