Socomec Green Power 2.0 User manual

green power 2.0 and Delphys BC

Modbus - TCP / Jbus serial link

Installation and operating manual GB

1. FOREWORD 4

2. SAFETY REQUIREMENT 4

2. 1. Using conditions 4

2. 2. dELPHYs grEEn PowEr oPErating rEfErEncE 4

3. ENVIRONMENT 4

3. 1. rEcYcLing of ELEctricaL ProdUcts and EqUiPmEnt 4

4. INTRODUCTION 5

4. 1. gEnEraL PUrPosE 5

4. 2. modbUs ProtocoL 5

4. 3. data dEcoding 5

5. INSTALLATION OF MODBUS RTU CARD 6

5. 1. ‘com-sLots’ LocaLisation 6

5. 2. modbUs sEriaL intErfacE PLUg in 6

5. 3. modbUs intErfacE in ParaLLEL sYstEm configUration 6

5. 4. connEctions and wiring 7

5. 5. com2 sEriaL Link dEfaULt sEttings 8

5. 6. How to cHangE tHE “sEriaL Link 2” sEttings ? 8

6. INSTALLATION OF MODBUS TCP CARD 9

6. 1. ‘com-sLots’ LocaLisation 9

6. 2. UPs com2 modbUs sEriaL Link dEfaULt sEttings 9

6. 3. dEfaULt sEttings of tHE modbUs tcP intErfacE 10

6. 4. framE Errors managEmEnt 11

7. CONVENTIONS 11

8. MODBUS IN SINGLE UPS UNIT 12

8. 1. How to rEad data 12

8. 2. incoming data strUctUrE 12

8. 3. UPs idEntification 13

8. 4. datE & HoUrs 13

8. 5. UPs configUration 13

8. 6. Unit statUs 14

8. 7. Unit aLarms 16

8. 8. Unit mEasUrEmEnts tabLEs 18

8. 9. Unit EnabLEd controLs tabLE 20

8. 10. controLs sEnd toUPs 20

INDEX

2Delphys green power - Ref.:

IOMDGPJB0910-GB_11

9. MODBUS IN MODULAR PARALLEL SYSTEM CONFIGURATION 21

9. 1. rEmindEr 21

9. 2. modbUs tabLE in modULar ParaLLEL sYstEm 22

9. 3. UPs idEntification 22

9. 4. datE & HoUrs 22

9. 5. UPs configUration 22

9. 6. PrELiminarY rEmarks 22

9. 7. UPs statUs 23

9. 8. UPs aLarms 24

9. 9. UPs mEasUrEmEnts 25

9. 10. UPs EnabLEd controLs tabLE 26

9. 11. tosEnd controL toUPs 26

10. MODBUS IN PARALLEL SYSTEM WITH CENTRALISED BYPASS 27

10. 1. rEmindEr 27

10. 2. modbUs tabLE in ParaLLEL sYstEm witH cEntraLisEd bYPass 28

10. 3. UPs idEntification 28

10. 4. datE & HoUrs 28

10. 5. UPs configUration 28

10. 6. PrELiminarY rEmarks 28

10. 7. UPs statUs 29

10. 8. UPs aLarms 30

10. 9. UPs mEasUrEmEnts 31

10. 10. UPs EnabLEd controLs tabLE 32

10. 11. tosEnd controL toUPs 32

11. BYPASS TABLE 33

11. 1. bYPass statUs 33

11. 2. bYPass aLarms 35

11. 3. bYPass mEasUrEmEnts tabLEs 37

12. MODULE TABLE 39

12. 1. modULE statUs 39

12. 2. modULE aLarms 41

12. 3. modULE mEasUrEmEnts tabLEs 43

13. ANNEXE 45

13. 1. modbUs tcP card wEb PagE 45

13. 2. modbUs tcP ida sPEcification 46

INDEX

Delphys green power - Ref.:

IOMDGPJB0910-GB_11

ENGLISH

We thank you for the trust you have in our Uninterruptible Power Systems.

This equipment is tted with up to date technology. Rectier and inverter subsets are provided with power semicon-

ductors (IGBT) including a digital micro-controller.

Our equipment complies with IEC EN 62040-2 standard.

CAUTION : “This is a product for restricted sales distribution to informed partners. Installation restrictions or addi-

tional measures may be needed to prevent disturbances”.

SOCOMEC reserves the right to modify their specifications at any time as far as this contributes to

technical progress.

2. SAFETY REQUIREMENT

2. 1. Using conditions

Do read carefully these operation instructions before using the JBUS/MODBUS interface.

Whatever the repairs, they must be made only by authorised staffs, which have been suitably trained.

For an optimal operation, it is recommended to maintain the ambient temperature and humidity of the DELPHYS

Green Power environment below the values specied by the manufacturer.

2. 2. dELPHYs grEEn PowEr oPErating rEfErEncE

Respect the safety requirements.

Do read carefully the operation instructions of DELPHYS Green Power.

This equipment meets the requirements of the European directives applied to this product. As a consequence it is

labelled as follows:

3. ENVIRONMENT

3. 1. rEcYcLing of ELEctricaL ProdUcts and EqUiPmEnt

Provision is made in European countries to break up and recycle materials making up the system. The various com-

ponents must be disposed of in accordance with the legal provisions in force in the country where the system is

installed.

1. FOREWORD

4Delphys green power - Ref.:

IOMDGPJB0910-GB_11

4. 1. gEnEraL PUrPosE

This document provides required information of the MODBUS protocol serial link or Ethernet network.

Before connecting a supervision equipment or BMS system (Building management system) to the UPS, it is neces-

sary to install and set up the serial interface or network congurations in the case of a network connection..

4. 2. modbUs ProtocoL

This document does not explain the MODBUS protocol management. Please refer on

www.modbus.org web site for more information.

The DELPHYS Green Power MODBUS uses the following functions :

–function 3 for reading Input Registers (16 bits),

–function 6 for writing single Registers (to control DELPHYS Green Power).

The data eld is composed of 1 word, dened by a MSB (most signicant byte) and a LSB (lowest signicant byte),

and displayed in the following order on the serial link.

1 WORD DATA

b7 MSB b0 b7 LSB b0

b15 b0

4. 3. data dEcoding

Status and alarms Information

This information are coding in bit. This means that 1 word denes 16 information. If the related bit is set to 1, this

information is active or true.

Measurements and counters data

1 word denes a measurement or a counter. Some values are numeric decimal signed or unsigned (0 to 65535 or

from -32767 to 32767), or in hexadecimal (0x0000 to 0xFFFF).

4. INTRODUCTION

Delphys green power - Ref.:

IOMDGPJB0910-GB_11

ENGLISH

5. 1. ‘com-sLots’ LocaLisation

The « Com-Slots » integrates all communication interfaces and it is located on the right side.

Please, see on the manual of the concerned UPS to see the correct localisation of the «com slot 2»

5. 2. modbUs sEriaL intErfacE PLUg in

The serial interface should be plugged in the slot 2, and xed with 2 crews.

5. 3. modbUs intErfacE in ParaLLEL sYstEm configUration

There is only one MODBUS serial link interface for a parallel system configuration. One serial interface

is used for the whole installation. The access to the data of the UPS module or unit is managed by the

table addressing .

In a parallel installation with centralized bypass, it is recommended to install the serial card in slot 2

of the bypass.

5. INSTALLATION OF MODBUS RTU CARD

6Delphys green power - Ref.:

IOMDGPJB0910-GB_11

5. 4. connEctions and wiring

NOTE : there is only one connection per interface (RS232 or RS422 or RS485)

5. 4.1. RS232 connection:

–Standard PC connection

–Sub-D 9 pins connector

–Pin 2 : Rx

–Pin 3 : Tx

–Pin 5 : GND

5. 4.2. Isolated RS485 connection

–2 wires connection

–« dip-switch 1 » allows connecting the terminal resistor

–Insulation via “opto-coupler”

–2 polarization resistors could be removed easily (if needed).

5. 4.3. Isolated RS422 connection

–4 wires connection

–« dip-switch 1 and 2 » allows connecting the terminal

resistor

–Insulation via “opto-coupler”

–4 polarization resistors could be removed easily (if needed).

RTX + RTX -

TX -

RX -

TX +

RX +

Before making any connection, please check the cabling. A wrong connection or cabling can damage

the serial link interface.

the shield should be earthing at one point.

InstallatIon InsIde UPs

Delphys green power - Ref.:

IOMDGPJB0910-GB_11

ENGLISH

5. 5. com2 sEriaL Link dEfaULt sEttings

Baud rate: 9600 bauds

Parity: NONE

Data: 8 bits

Stop: 1 bit

Slave: 1

The serial link settings can be set from the control panel.

5. 6. How to cHangE tHE “sEriaL Link 2” sEttings ?

Available baud rate: 1200 - 2400 - 4800 - 9600 - 19200 bauds

Parity: EVEN - ODD - NONE

Slave number: 1 to 32

Please, see on the manual of the concerned UPS to see the correct localisation of the «com slot»

InstallatIon InsIde UPs

8Delphys green power - Ref.:

IOMDGPJB0910-GB_11

6. 1. ‘com-sLots’ LocaLisation

The « Com-Slots » integrates all communication interfaces and it is located on the right side.

Please, see on the manual of the concerned UPS to see the correct localisation of the «com slot 2»

6. 2. UPs com2 modbUs sEriaL Link dEfaULt sEttings

Baud rate: 9600 bauds

Parity: NONE

Data: 8 bits

Stop: 1 bit

Slave: 1

The serial link settings can be set from the control panel.

These settings are compulsory to make the Modbus TCP communication available

6. INSTALLATION OF MODBUS TCP CARD

Delphys green power - Ref.:

IOMDGPJB0910-GB_11

ENGLISH

6. 3. dEfaULt sEttings of tHE modbUs tcP intErfacE

DEFAULT SETTING

DHCP mode by default. No IP address set by default

Mode MODBUS TCP

Port TCP 502

DISCOVERY TOOL

Download AGILIPLUG utility from SOCOMEC web site.

Unzip the le on your computer (only Windows)

run AGILIPLUG Finder program

SEARCHING UPS CONNECTED

AGILIPLUG Finder lists all IP addresses of MODBUS TCP interface connected to network.

INTERFACE CONFIGURATION

The MODBUS TCP Interface detects automatically the baud arte of serial link.

Opening the web page, allows to change IP settings.

password: public

10 Delphys green power - Ref.:

IOMDGPJB0910-GB_11

Other manuals for Green Power 2.0

This manual suits for next models

Table of contents

Other socomec UPS manuals

socomec

socomec MASTERYS IP Plus User manual

socomec

socomec netis rt User manual

socomec

socomec ITYS User manual

socomec

socomec NeTYS PE 600 VA User manual

socomec

socomec NETYS PR-RT Series User manual

socomec

socomec MASTERYS BC 15 User manual

socomec

socomec MASTERYS BC 60 kVA User manual

socomec

socomec MASTERYS GP4 Series User manual

socomec

socomec MASTERYS GP4 Series User manual

socomec

socomec Green Power 2.0 User manual

socomec

socomec NETYS RT User manual

socomec

socomec Green Power 2.0 60 User manual

socomec

socomec Masterys BC User manual

socomec

socomec DELPHYS MX 250 User manual

socomec

socomec MODULYS GP 25 kVA User manual

socomec

socomec OFYS RT User manual

socomec

socomec NETYS RT User manual

socomec

socomec Masterys BC User manual

socomec

socomec Modulys GP 2.0 Series User manual

socomec

socomec Green Power 2.0 600 kVA User manual

socomec

socomec NETYS PE User manual

socomec

socomec ITYS User manual

socomec

socomec ITYS PRO 10 User manual

socomec

socomec MASTERYS IP+ User manual

Popular UPS manuals by other brands

Pylontech

Pylontech Victron & Pylontech US5000 manual

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 user manual

Mecer

Mecer ME-1000-WTU user manual

Mustek

Mustek PowerMust 530(B) Plus Startup manual

Emerson

Emerson Liebert NXL series Operation and maintenance manual

MAKELSAN

MAKELSAN BOXER SERIES user manual

Block

Block PC-0524-400-0 manual

CyberPower

CyberPower CP585LCD user manual

Eaton

Eaton 3S Advanced user's guide

CyberPower

CyberPower Office Tower Series UPS 1000 user manual

CyberPower

CyberPower BM100 quick start guide

Best Power

Best Power 610 quick start guide

Best Power

Best Power Unity/I UT3K user manual

Mustek

Mustek PowerMust 400 Offline user manual

Xantrex

Xantrex Trace 512 UR-UPS owner's manual

Forza

Forza SL-1501UL user manual

LEGRAND

LEGRAND keor 310081 quick start guide

ABB

ABB Conceptpower DPA 500 operating manual