Snap One Araknis Networks User manual
Welcome to Araknis Networks™
Thank you for choosing an Araknis™ Wi-Fi 6 Wireless Access Point (AP). With a circular
housing, an easy mounting system, convenient PoE power, and the latest Wi-Fi 6
wireless technologies, these products are ideal as staples in both residential and
commercial applications.
Features
l802.11AX Wi-Fi 6 Certified
lSleek circular design
l1× 2.5 Gigabit LAN port w/PoE-IN
l1× Gigabit LAN port (data only)
lAN-820-AP-I: 4×4 dual-band 802.11AX
3600Mbps
lAN-520-AP-I: 2x2 dual-band 802.11AX
3000Mbps
lOvrC enabled
1
Unbox the AP
The package contains:
Access point (AP) Mounting bracket Tile ceiling backing
plate
Quick Start Guide
QRcard
Male-to-femaile
category jumper
cable
Tile ceiling
mounting
hardware
Drywall mounting
hardware
Wood surface
mounting
hardware
Note: -__.This guide uses the 820 AP for illustrative purposes.
2
Installing the AP
How to Remove the Cable Bay Cover Ceiling Mount
Note: -__.Use the ceiling back plate on top of acoustic ceiling tiles to prevent the
mounting nuts from pulling through the tile.
3
Positioning the Ceiling Mount
* The center line of the bracket is not necessarily the center line of the AP when it's being
installed. Use the above guide to understand the center line of the AP when installing
the bracket.
4
Using the Jumper Cable
You can mount your access point to the electrical box in one of two positions, shown
below. These options are provided to provide cable bend relief for cables of different
lengths and thicknesses. The illustrations do not reflect pre-install steps. Run the
wire or jumper prior to connecting the access point.
Note: -__.Use the jumper cable when using Cat 6A in Position B.
5
Connections
Note: -__.This AP requires 802.3at (30W) PoE. Do not use 802.3af (15W) or a passive
PoE injector as 15W is only enough to power the device, connect to OvrC, and
broadcast an SSID with minimal throughput.
6
LED Operation and Resets
LED Behavior
APState LED Behavior Description
Operational States
No LED The APis not powered on.
Solid White The AP is in the uboot stage of the startup
process.
Blinking White The AP is at the kernel stage of the startup
process.
SolidBlue The AP started correctly and is running in
an operational state.
Blinking Blue The AP is operational but is
underpowered.
Error States
Blinking
Orange The APis not connected to the internet.
Blinking Green The AP is updating it's firmware.
SolidOrange The APfailed a firmware update and
needs to be recovered.
Solid Red The AP is non-functional.
7
How to Perform a Hardware Factory Default
Press and hold the Reset button for more than 20 seconds. Release the button when the
LED blinks red.
Allow two to four minutes for the AP to restart and load the factory default settings, then
log into the AP using the default username and password (araknis; araknis) and
configure the AP like new, or upload a configuration file.
Reset Button Action LEDState Description
Hold the reset button for 1-9
seconds
Blinking
Green Restarts the AP
Hold the reset button for 10-19
seconds*
Blinking
Orange
Only resets the username and
password
Hold the reset button for more than
20 seconds
Blinking
Red
Resets the AP to factory
defaults
*This action is only available when the Reset Password toggle is disabled in the web
interface.
8
Configuration
Araknis APs can be configured through OvrC or the local interface. The local interface is
accessible using OvrC’s webconnect feature, typing the AP’s DHCP address into your
browser’s address bar, or using the AP’s default IP address.
Configuring the AP in OvrC
OvrC provides Wi-Fi management, remote device management, real-time notifications,
and intuitive customer management, using your computer or mobile device. Setup is
plug-and-play, with no port forwarding or DDNS address required.
To add this device to your OvrC account:
1. Connect the AP to the internet
2. Log into OvrC (www.ovrc.com)
3. Scan the site using an OvrC Pro
device, or add the AP manually by
entering the MAC address and
Service Tag.
4. Click here for our article on Getting
Started With OvrC Wi-Fi
Management.
9
Logging into the Web Interface
1. Log into the AP using the default
credentials:
Username araknis
Password araknis
2. You must update the password after
initial login.
Pro Tip: -_Strong passwords are long and unrelated to the client’s public details. For
example, thepepperonipizzas is stronger and easier to remember than
P@ssword or thesmiths.
10
Table of contents
Other Snap One Wireless Access Point manuals
