Smart-IR smartbell User manual
Smart Wireless Doorbell
User Manual
Version 1
Designed & Engineered
in the United Kingdom
smartbell
Contents
Precautions .............................................................................................. 3
1. Product Overview ................................................................................ 4
1.1. Product Features .................................................................... 4
1.2. Contents ................................................................................. 4
2. Installation ........................................................................................... 5
2.1. DIY Installation ....................................................................... 5
2.2. Professional Installation ......................................................... 6
2.3. Smartbell Overview ................................................................ 8
3. App Setup ........................................................................................... 9
3.1. Installing Smartbell App .......................................................... 9
3.2. Connecting to View Remotely ................................................. 11
4. Software Use ....................................................................................... 13
4.1. Settings ................................................................................... 13
4.2. Software Settings .................................................................... 13
4.2.1 Search for Screenshot .............................................. 13
4.2.2 Video ......................................................................... 14
4.2.3 Unlock the Door ........................................................ 14
4.3. Device Settings ...................................................................... 14
4.3.1 Favourite ................................................................... 15
4.3.2 Change Device Info .................................................. 15
4.3.3 Move Detection ........................................................ 15
4.3.4 Change Device Network ........................................... 15
4.3.5 About Device ............................................................. 16
4.3.6 Alarm ......................................................................... 16
4.3.7 Security Settings ....................................................... 16
4.3.8 SD Formatting ........................................................... 16
4.3.9 Turn Off ..................................................................... 17
5. Ringer ................................................................................................... 18
6. Specifications ...................................................................................... 19
Thank you for purchasing the smartbell smart wireless doorbell.
Before installing your new system, please read the instructions carefully.
3
1. Please install your system according to this manual to avoid any malfunctions or damage.
2. Never open the smartbell, please contact your installer or place of purchase in the event of product
malfunction.
3. Keep the smartbell away from extreme heat sources and water.
4. Never use any cleaning chemicals or wet cloth to clean the unit. Only use a dry, clean and soft
cloth/micro fibre coth.
5. Do not use the product in places where there are explosive hazards
6. Do not drop the unit or submit to heavy shaking
7. Keep chargers and power supplies away from liquids
8. Use your unit in temperature between -20 and 60° C
9. Storage temperature must be between -10 and 60° C
Safety Instructions
Precautions
1.1 Product Features
4
1. Product Overview
See & speak to callers from anywhere in the world
PIR/Conference/Tamper Function (Not supported on
all models, please check with your supplier)
Motion Detection
Weatherproof - IP55
1.2 Contents
1x Power Cable 1x Permanent
Power Lead
5x Screws
5x Wall Plugs
1x User Manual1x Wireless
Outdoor Camera
1x Wireless Doorbell 1x Battery for Wireless
Doorbell
Standard Version:
As well as the standard version, the plus ringer
version includes the following:
Plus Ringer Version:
SmartWireless Doorbell
User Manual
Version1
Designed&Engineered
intheUnitedKingdom
smartbell
4x Screw Plug
Covers
1x Safety Screw &
Cover for Bracket
Electric Door Release Feature Supported (Lock not
supplied)
Visitor Memory
IR LEDs - For low light viewing
As well as the standard version, the Pro version
includes the following:
Pro Version
1x 20m Extension Cable
To complete installation, you will need the following:
Philips Head Screw Driver
Drill (Depending on install location)
Small Flat Head Screw Driver
Patch Ethernet Cable (Length depending on install location from router/home plug/switch)
Terminal Block (Pro Install)
Micro SD Card (For Recording images & video)
Router wifi SSID and Password for Remote Access
Pre Requisites
5
2. Installation
2.1 DIY Installation
1. Remove the smartbell from the bracket. Use the
bracket as a stencil and place where you wish to install
the smartbell. Then, mark out the screw holes to
secure the bracket.
2. Mark a hole for the power and ethernet cable to
run through. Remove the bracket, and then drill the
holes. We recommend any holes you drill in your
walls are sealed water tight after your cables are
thread through.
3. Attach the bracket to the wall using the wall plugs
and screws included.
4. Push the red/black cables of the permanent power
lead through the hole in the wall and connect to the back
of the smartbell. The red wire into the number 1 slot and
black into the number 2 slot. To do this, push and hold
the grey clip in while pushing in the red//black cables.
When pushed in, release the clip to secure the wire.
At this point, please make a note of the unit’s
Access point (AP) name. This can be found on the
sticker at the back of the unit (shown above, right).
You will need this number later.
AP
Name
If you are a professional installer, please go to Section 2.2 on page 6
6
6. Insert your Micro SD Card (if you have purchased
one) to enable recording.
8. Connect the end of the permanent power lead to
the power supply provided and plug the power supply
into a power source. Your DIY install is complete, for
the next step, go to Section 3 ‘App Set Up’.
2.2 Professional Installation
If there is no power source locally, you can use the optional 20m DC extension lead accessory (see page 4). To use the
additional cable, follow the instructions below.
5. If you will using a wired connection to your router,
run your ethernet cable through the hole and connect
to the back of the smartbell. Attach as shown above.
If you are connecting wireless, skip to step 6.
5. If you choose a wired connection to your router/home
plug/switch, run your ethernet cable through the hole
and connect to the back of the smartbell. Attach as
shown above. If you choose a wireless connection skip
this step and proceed to step 6.
1. Remove the smartbell from the bracket. Use the
bracket as a stencil and place where you wish to install
the smartbell. Then, mark out the screw holes to secure
the bracket.
7. Put the screw cap covers in place over the screws at
the back of the smartbell. Attach the smartbell to the
bracket. Secure the unit to the bracket using the provided
screw and place at the bottom of the unit. Then use the
cap to cover (shown above, right).
2. Mark a hole for the power and ethernet cable to
run through. Remove the bracket, and then drill the
holes. We recommend any holes you drill in your
walls are sealed water tight. After threading the
cables through.
7
4. Take the permanent power lead and plug it into the
DC plug on the power supply provided. Please DO
NOT plug the power supply into your power source at
this point.
5. Connect the red/black end of the permanent
power lead to a terminal block and the optional
20m extension lead. Put the same colours from the
20m extension into the matching connections on
the terminal block.
3. Attach the bracket to the wall using the wall plugs
and screws included.
6. Push the red/black cables of the permanent power
lead through the hole in the wall and connect to the back
of the smartbell. The red wire into the number 1 slot and
black into the number 2 slot. To do this, push and hold
the grey clip in while pushing in the red//black cables.
When pushed in, release the clip to secure the wire.
At this point, please make a note of the unit’s
Access point (AP) name. This can be found on the
sticker at the back of the unit (shown above, right).
You will need this number later.
AP
Name
2.3 Smartbell Overview
8
1. Camera
2. Speaker
3. Microphone
4. IR LEDs
7. Doorbell
5. If you will using a wired connection to your router,
run your ethernet cable through the hole and connect
to the back of the smartbell. Attach as shown above.
If you are connecting wireless, skip to step 6.
10. Now, plug the power supply into a power source.
Your smartbell is now ready to configure using the
smartbell app. Proceed to Section 3 ‘App Setup’.
8. Insert your Micro SD Card (if you have purchased
one) to enable recording.
9. Put the screw cap covers in place over the screws at
the back of the smartbell. Attach the smartbell to the
bracket. Secure the unit to the bracket using the provided
screw and place at the bottom of the unit. Then use the
cap to cover (shown above, right).
7. If you choose a wired connection to your router/home
plug/switch, run your ethernet cable through the hole
and connect to the back of the smartbell. Attach as
shown above. If you choose a wireless connection skip
this step and proceed to step 6.
6. Name Tag
5. PIR Sensor
9
3. App Setup
3.1 Installing Smart-i Bell App
Please follow the steps below to install the Smart-i Bell app. The screen shots shown in the examples are taken
from a Samsung Galaxy Note 4, so these may vary depending on which model of Smartphone/Tablet you use.
1. Turn on the wireless on your Smartphone or Tablet by going to your settings and selecting the wifi option
shown below (right).
3. Go to the your App/Google Play store and download the ‘smart-i bell app’.
2. Select the smartbell wifi from the search list. When selected, type in the password (default password is
12345678).
4. Once installed, the app will then appear on your homescreen. Click the icon to open the App.
5. Press on the ‘Add device’ icon.
10
6. Press the Search in LAN option.
7. The device number shown on screen should match with the sticker on the back of the unit.
8. Select the correct device and fill in the details for the smartbell. The default password for this is 88888888.
9.When all the details are entered, press the icon on the top right of the screen. You will be re-directed to
the homesscreen (below).
Home WIFI
Name: Enter any username, for example Smart-i Bell.
Device ID: This is unique to the smartbell you are
adding.
Password: Enter the password of the device you are
trying to add. The default password is 88888888.
Table of contents
