Slinex IP DIRECT Series User manual

DIRECT

SERIES

1. Wiring diagram

Equpment conﬁguration consists of several steps: basic network settings, logical address setting and server IP address

setting for calls redirection. Indoor monitor or outdoor panel parameters can be changed through the Slinex IP Tool

software. Connection schematic diagram described below:

Note:

* Calls redirection server IP address has been taken from the local network: 192.168.1.134, this address must be the

same for all devices inside the system.

** Logical address of the door panel and internal monitor for the current building and entrance must have the same

parameters.

2. Indoor monitor conﬁguration

2.1. Network settings

Network settings conﬁguration can be changed on the next bookmark: File

→

Normal Attribute.

For example, following parameters were applied for the monitor network settings:

Note:

* Following settings can be applied through the monitor interface: date, time, passwords, network settings and the logical

address setting.

** Before monitor will be connected to the local network make sure that computer have the same subnet mask with the monitor.

The default network settings are: IP Address: 192.168.14.252; subnet Mask: 255.255.0.0; gateway number: 192.168.14.254;

{ Design. Uniqueness. Innovations }

QUICK INSTALLATION GUIDE

IP Address: 192.168.1.10

Logical address: 01010001

IP Address: 192.168.1.11

Logical address: 01 01 00

Logical address consists of:

Block –

Building: 01;

(up to 2 digits max);

Unit – Entrance: 01; (up to 2 digits max;

Floor Number – Floor: 00; (up to 2 digits max);

Room Number – Room: 01; (up to 2 digits max) ;

Following logical address of the monitor was seted as an example: 0101 00 01;

2.3. Call redirection server settings

Call redirection server settings can be changed on the next bookmark:

File

→

Advance Attribute.

Following call redirection server settings wwere seted as an example:

2.2. Logical address settings

Logical address settings conﬁguration can be changed on the next bookmark:

File → Advance Attribute →Parameter Setting.

IP address of the server must be the same for all devices inside one system.

UPS

Outdoor panel

Router

Individual panel Indoor monitor

Power supply

{ Design. Uniqueness. Innovations } IP

DIRECT

SERIES

Logical address consists of:

Block –

Building: 01;

(up to 2 digits max);

Unit – Entrance: 01; (up to 2 digits max);

Following logical address of the monitor was seted as an example: 0101;

Leave the other options unchanged.

3.3. Call redirection server settings

Call redirection server settings can be changed on the next bookmark:

File

→

Advance Attribute.

Following call redirection server settings wwere seted as an example:

Safety instructions

Read and keep that manual.

This instruction is additional, interchangeable for operating instructions: indoor monitors, outdoor cameras, guard statiouns.

Instruction can be use to conﬁgurate a group of devices in the same local network. With this tutorial you can change the

parameters of the network, logical addressing, alarm zones, and other settings.

This manual is intended for engineers, installers, of security systems, for installation and mounting when you conﬁgure the

devices for installation and mounting.

Rights and limitation of liability

As a result of continuous upgrades and functionality improvements, technical characteristics of the device can be changed

without any preliminary declaration.

This manual can contain some inaccuracy or misprint. The owner reserves the right to make corrections to the information

described in the user manual and device package.

reproduced in any way including electronic or mechanical.

Document recording and copying is strictly denied without owner permission.

3. Indoor monitor conﬁguration

3.1. Network settings

Network settings conﬁguration can be changed on the next bookmark: File

→

Normal Attribute.

For example, following parameters were applied for the monitor network settings:

Note:

* Following settings can be applied through the monitor interface: date, time, passwords, network settings and the logical

address setting.

** Before monitor will be connected to the local network make sure that computer have the same subnet mask with the monitor.

The default network settings are: IP Address: 192.168.14.252; subnet Mask: 255.255.0.0; gateway number: 192.168.14.254;

IP address of the server must be the same for all devices inside one system. Leave the other options unchanged.

3.2. Logical address settings

Logical address settings conﬁguration can be changed on the next bookmark:

File → Advance Attribute →Parameter Setting.

Other Slinex Intercom System manuals

Popular Intercom System manuals by other brands

Bticino

Bticino LINEA 3000 Installation

MSI

MSI MSI-140 owner's manual

golmar

golmar Stadio Plus instruction manual

CyberData

CyberData 011211 series Installation quick reference

Vidos

Vidos duo M1021 user manual

Vimar

Vimar ELVOX 7539/E Installation and operation manual

SSS Siedle

SSS Siedle BTSV 850-03 operating instructions

Dahua

Dahua VTO Series quick start guide

Elvox

Elvox 5651 Wiring instructions

Videx

Videx VIDEOKIT Series owner's manual

Rocom

Rocom Doortello Business FW T2.05W2.04 user guide

Viking

Viking E-35-EWP product manual

Safeguard Supply

Safeguard Supply LRA-EX1000 user manual

SSS Siedle

SSS Siedle BFCV 850 Series operating instructions

GRD

GRD MAX V2 user manual

Alecto

Alecto ADI-250 user manual

Aiphone

Aiphone IE-8MD Installation & operation manual

Perel

Perel EDB4 user manual