Siruba 700KT User manual
700KT
使用說明書與零件圖
INSTRUCTION BOOK & PARTS LIST
誌
i
索引 INDEX 頁/PAGE
一般安全事項說明 GENERAL SAFETY INSTRUCTIONS 1
重要安全事項說明 IMPORTANT SAFETY INSTRUCTIONS 3
特別事項 WARNING 7
警告標籤 WARNING TAG 8
護針安全圖說 SAFETY ILLUSTRATION OF THE NEEDLE GUARD 9
搬運縫紉機 MOVING THE SEWING MACHINE 9
縫紉機的安裝位置 THE INSTALLATION POSITION OF THE SEWING MACHINE 10
規格 SPECIFICATIONS 11
各部件名稱 NAMES OF MAJOR PARTS 13
機器安裝 HOW TO INSTALL THE NEW MACHINE 14
新機器使用規定 HOW TO OPERATE THE NEW MACHINE 16
潤滑油之注入與更換 LUBRICATION AND DRAINAGE 16
穿線方式 THREADING THE MACHINE 18
控線調整 ADJUST THREAD TENSION 19
換針方式 REPLACE THE NEEDLE 21
針距調整 ADJUST THE STITCH LENGTH 21
差動比調整 ADJUST THE DIFFERENTIAL FEED RATIO 22
更換切刀 REPLACE THE TRIMMERS 23
包縫寬度調整 ADJUST THE HEM WIDTH 24
針高度之調整 ADJUST THE NEEDLE HEIGHT 24
押具調整 ADJUST THE PRESSER FOOT 25
送具調整 ADJUST THE FEED DOG 27
針與勾針之關係 THE RELATIONSHIP BETWEEN NEEDLE AND LOOPER 29
環勾針運動之調整 ADJUST THE CHAINSTITCH LOOPER MOVEMENT AMOUNT 31
上送具高低行程調整 ADJUSTMENT OF THE HIGH-LOW STROKE OF THE UPPER FEED DOG 32
上送具與差動齒之關係 RELATION BETWEEN THE UPPER FEED DOG AND THE 32
DIFFERENTIAL FEEDER
上送具前後行程調整 ADJUST THE FRONT-REAR STROKE OF UPPER FEEDER 33
定位勾針線挑線凸輪 POSITION THE LOOPER AND TAKE-UP THREAD CAM 34
報廢流程 DEMOLITION PROCEDURE 35
桌板圖 TABLE CUT-OUT 36
規格件表 GAGE PARTS LIST 37
零件圖 PARTS LIST 38
ii
Introduction
場所良好的照明。當有引發火災或爆炸危
險時，勿使用電源工具。
防範於電擊危害
物品
h
Consider environment’s safety
may be caught in moving parts.Wear
object.
cause
-1-
P1
有
-2-
P2
Introduction
-3-
7.Hazardous Voltage will cause injury,
please turn off the power switch or
disconnect it for any one of the
circumstances of the followings:
(1) Turn off the main switch and wait for 5
minutes, before opening this cover to
protect yourself from danger.
(2) When threading needle(s), adjusting
thread Take-up(s),thread
guide(s),and/or replacing bobbin(s).
(3) When replacing needles, presser
feet, needle plates, feed dogs needle
guard, folder, cloth guides and other
parts or accessories.
7.此符號代表高電壓易導致發生危
險，以下情形，請先關閉電源或拔
掉插頭：
(1)若需拆開電控箱蓋時，請先關閉
電源五分鐘後，才能拆開電控箱
蓋，以避免誤觸電壓造成危險。
(2)穿針線﹑線導片﹑天平等以及更換
梭子時。
(3)更換針板押具﹑送具﹑頂針片﹑喇
叭﹑車布導板，以及其他附屬配件
時。
P3
４
５
６
４
５
６
P4
Introduction
有接地線的之插座上。
因私自
標誌
-5-
P5
-6-
P6
Introduction
-7-
)
)
做好接地作業。
ground.
P7
Table of contents
Other Siruba Sewing Machine manuals
Siruba
Siruba NC008 User manual
Siruba
Siruba ASP-EBJ100S User manual
Siruba
Siruba DL7200D-NM1 User manual
Siruba
Siruba VC008B User manual
Siruba
Siruba 700KS User manual
Siruba
Siruba DL7200B User manual
Siruba
Siruba Sew Reach F007KD User manual
Siruba
Siruba ASP-PTA100 User manual
Siruba
Siruba DL720 User manual
Siruba
Siruba 700F User manual
Siruba
Siruba ASL-JBH200C User manual
Siruba
Siruba VC008 VSQ User manual
Siruba
Siruba DL7200 User manual
Siruba
Siruba Siruba HSO-747 User manual
Siruba
Siruba C007K User manual
Siruba
Siruba HSO-747D User manual
Siruba
Siruba T828-TP Datasheet
Siruba
Siruba DT828L User manual
Siruba
Siruba BH780 Datasheet
Siruba
Siruba LZ457A Datasheet
